Emerson Rosemount 3051P Manuel utilisateur

Quick Start Guide

00825-0200-4007, Rev AD

May 2019

Rosemount™ 3051P Pressure Transmitter

with 4-20 mA HART® Protocol (Revision 5

and 7)

Contents

About this guide...........................................................................................................................3

System readiness......................................................................................................................... 4

Mount the transmitter..................................................................................................................6

Set the switches......................................................................................................................... 10

Connect the wiring and power up...............................................................................................11

Verify transmitter configuration.................................................................................................14

Trim the transmitter...................................................................................................................20

Safety instrumented systems..................................................................................................... 23

Product Certifications.................................................................................................................24

Quick Start Guide May 2019

2 Emerson.com/Rosemount

1 About this guide

This installation guide provides basic guidelines for Rosemount™ 3051P

Transmitters. It does not provide instructions for configuration, diagnostics,

maintenance, service, troubleshooting, Explosion-Proof, Flame-Proof, or

intrinsically safe (I.S.) installations. Refer to the Rosemount 3051P Reference

Manual for more instruction. This manual is also available electronically on

Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in

accordance with the appropriate local, national, and international

standards, codes, and practices. Review the approvals section of the

Rosemount 3051P Reference Manual for any restrictions associated with

a safe installation.

Do not remove the transmitter cover in explosive atmospheres when the

circuit is live.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the O-ring designed to seal with the

corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

Conduit/cable entries

Unless otherwise marked, the conduit/cable entries in the housing

enclosure use a ½–14 NPT form. Only use plugs, adapters, glands, or

conduit with a compatible thread form when closing these entries.

Physical access

Unauthorized personnel may potentially cause significant damage to

and/or misconfiguration of end users’ equipment. This could be

intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for all

systems used within the facility.

May 2019 Quick Start Guide

Quick Start Guide 3

2 System readiness

2.1 Confirm HART revision capability

•If using HART® based control or asset management systems, confirm the

HART capability of those systems prior to transmitter installation. Not all

systems are capable of communicating with HART Revision 7. This

transmitter can be configured for either HART Revision 5 or 7.

•For instructions on how to change the HART revision of your transmitter,

see Switch HART revision mode.

2.2 Confirm correct device driver

Procedure

1. Verify the latest Device Driver (DD/DTM™) is loaded on your systems

to ensure proper communications.

2. Reference Emerson.com or FieldCommGroup.org for the lated DD.

3. Select desired product and download the DD.

a) Reference Table 1, for the correct DD.

Table 2-1: Device Revisions and Files

Identify device Find device driver

files

Review

instructions

Review

functionality

Software

release

date

NAMUR

hardware

revision

(1)

NAMUR

software

revision

(1)

HART®

software

revision

(2)

HART

universal

revision

Device

revision

(3)

00809-0100

-4007

Changes to

software(4)

August

2016

1.1.xx 1.0.xx 03 7 10 Rosemount™

3051P In-

line Pressure

Transmitter

with HART

Protocol

Reference

Manual

(4)

5 9

(1) NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes,

signified above by xx, represent minor product changes as defined per NE53. Compatibility

and functionality are preserved and product can be used interchangeably.

(2) HART software revision can be read using a HART capable configuration tool. Value shown

is minimum revision that could correspond to NAMUR revisions.

(3) Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed

to enable legacy device driver revisions to continue to communicate with new HART devices.

To access new functionality, the new device driver must be downloaded. It is recommended

to download new device driver files to ensure full functionality.

Quick Start Guide May 2019

4 Emerson.com/Rosemount

(4) HART Revision 5 and 7 selectable, Local Operator Interface (LOI), scaled variable,

configurable alarms, expanded engineering units. Updated electronics hardware design.

Intrinsic Safety temperature classification change.

May 2019 Quick Start Guide

Quick Start Guide 5

3 Mount the transmitter

Mount directly to the impulse line without using an additional mounting

bracket or mount directly to a wall, panel, or two-inch pipe using an optional

mounting bracket.

Figure 3-1: Transmitter Direct Mounting

Do not apply torque directly to the electronics housing. To avoid damage,

apply torque only to the hex-shaped process connection.

A. Process connection

Figure 3-2: Panel and Pipe Mounting

Panel mount Pipe mount

Quick Start Guide May 2019

6 Emerson.com/Rosemount

3.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 3-3: Mounting the Transmitter in Liquid Applications

In-line

3.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 3-4: Mounting the Transmitter in Gas Applications

Inline

May 2019 Quick Start Guide

Quick Start Guide 7

3.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 3-5: Mounting the Transmitter in Steam Applications

In-line

3.4 Environmental seal for housing

Thread sealing (PFTE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seals and meets requirements of NEMA®

Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings

are required.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

3.5 Gage transmitter orientation

The low side pressure port (atmospheric reference) on the inline gage

transmitter is located in the neck of the transmitter, behind the housing. The

vent path is 360° around the transmitter between the housing and sensor.

(See Figure 3-6.)

Quick Start Guide May 2019

8 Emerson.com/Rosemount

CAUTION

Keep the vent path free of any obstruction, including but not limited to

paint, dust, and lubrication by mounting the transmitter so the

contaminants can drain away.

Figure 3-6: Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

May 2019 Quick Start Guide

Quick Start Guide 9

4 Set the switches

Set alarm and security switch configuration before installation as shown in

Figure 4-1.

•The alarm switch sets the analog output alarm to high or low. Default

alarm is high.

•The security switch allows ( ) or prevents ( ) any configuration of the

transmitter. Default security is off ( ).

Use the following procedure to change the switch configuration:

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not

remove the instrument cover in explosive atmospheres when the

circuit is live.

3. Slide the security and alarm switches into the preferred position

using a small screwdriver.

4. Reattach the transmitter cover. The cover must be fully engaged to

comply with explosion-proof requirements.

Figure 4-1: Transmitter Electronics Board

Without LCD display With LOI/LCD display

A. Alarm

B. Security

Quick Start Guide May 2019

10 Emerson.com/Rosemount

Autres manuels pour Rosemount 3051P

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 1408A Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 3051N Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 4600 Manuel utilisateur

Emerson

Emerson Micro Motion 4200 Manuel utilisateur

Emerson

Emerson MICRO MOTION 2700 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Guide de configuration

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Rosemount 3051 CF Series Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 3051G Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Micro Motion 3500 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Micro Motion 3700 Manuel utilisateur

Emerson

Emerson Rosemount 2051G Manuel utilisateur

Emerson

Emerson Rosemount 3300 Series Manuel utilisateur

Emerson

Emerson Rosemount CX1100 Manuel utilisateur

Emerson

Emerson Rosemount 3144P Manuel utilisateur

Emerson

Emerson Rosemount OCX 8800 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Rosemount 248 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur