Emerson Rosemount 3051HT Manuel utilisateur

Quick Start Guide

00825-0200-4091, Rev CA

June 2020

Rosemount™ 3051HT Hygienic Pressure

Transmitter

with FOUNDATION™ Fieldbus Protocol

NOTICE

This guide provides basic guidelines for the Rosemount 3051HT Transmitter. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or intrinsically safe (I.S.) installations.

WARNING

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,

national, and international standards, codes, and practices.

In an explosion-proof/flameproof installation, do not remove the transmitter covers when power is

applied to the unit.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the gasket designed to seal with the corresponding flange adapter.ph>

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end

users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Conduit/cable entries

Unless otherwise marked, the conduit/cable entries in the housing enclosure use a ½–14 NPT form.

Only use plugs, adapters, glands, or conduit with a compatible thread form when closing these entries.

Contents

System readiness......................................................................................................................... 3

Transmitter installation................................................................................................................ 4

Product certifications................................................................................................................. 21

Quick Start Guide June 2020

2 Emerson.com/Rosemount

1 System readiness

Note

Before installing the transmitter, confirm that the correct device driver is

loaded on the host systems.

1.1 Confirm correct device driver

•Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

•Download the latest device driver at Emerson.com or

FieldCommGroup.org.

Rosemount 3051 device revisions and drivers

Table 1-1 provides the information necessary to ensure you have the correct

device driver and documentation for your device.

Table 1-1: Rosemount 3051 Device Revision 8 and Drivers

FOUNDATION™ Fieldbus device revision can be read using a FOUNDATION Fieldbus capable

configuration tool.

Host Device driver (DD)(1) Obtain at Device driver

(DTM)

Manual

document

number

All DD4: DD Rev 1 FieldCommGroup.org Emerson.com 00809-0100-47

74, Rev CA or

newer

All DD5: DD Rev 1 FieldCommGroup.org

Emerson AMS Device Manager V

10.5 or higher: DD Rev 2

Emerson.com

Emerson AMS Device Manager V

8 to 10.5: DD Rev 1

Emerson.com

Emerson 375/475: DD Rev 2 Easy Upgrade Utility

(1) Device driver file names use device and DD revision. To access functionality, the correct

device driver must be installed on your control and asset management hosts, and on your

configuration tools.

June 2020 Quick Start Guide

Quick Start Guide 3

2 Transmitter installation

Figure 2-1: Installation Flowchart

2.1 Mount the transmitter

Place the transmitter to the desired orientation before mounting.

Transmitter must not be securely mounted or clamped in place when

changing transmitter orientation.

Conduit entry orientation

When installing a Rosemount 3051HT, it is recommended installing so a

conduit entry faces downward or parallel to the ground to maximize

drainability when cleaning.

Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a watertight/dustproof conduit seal and meets requirements of

NEMA® Type 4X, IP66, IP68, and IP69K. Consult factory if other Ingress

Protection ratings are required.

Note

IP69K rating only available on units with a SST housing and option code V9 in

the model string.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

In-line gauge transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located on the neck of the transmitter via a protected gage

vent (See Figure 2-2).

Keep the vent path free from obstructions including but not limited to paint,

dust, and viscous fluids by mounting the transmitter so the process can drain

away.

Quick Start Guide June 2020

4 Emerson.com/Rosemount

Figure 2-2: In-line Protected Gage Vent Low Side Pressure Port

Aluminum Polished 316 SST

A. Low side pressure port (atmospheric reference)

Clamping

When installing clamp, follow recommended torque values provided by

gasket manufacturer.

Note

To maintain performance, torquing a 1.5-in. Tri Clamp beyond 50 in-lb. is

not recommended on pressure ranges below 20 psi.

June 2020 Quick Start Guide

Quick Start Guide 5

2.2 Commissioning (paper) tag

To identify which device is at a particular location use the removable tag

provided with the transmitter. Ensure the physical device tag (PD Tag field)

is properly entered in both places on the removable commissioning tag and

tear off the bottom portion for each transmitter.

Figure 2-3: Commissioning Tag

Commissioning Tag

DEVICE ID:

001151AC00010001440-121698091725

DEVICE REVISION:

PHYSICAL DEVICE TAG

DEVICE ID:

001151AC00010001440-121698091725

DEVICE REVISION:

S / N :

PHYSICAL DEVICE TAG

Device Barcode

A. Device revision

Note

The device description loaded in the host system must be at the same

revision as this device. The device description can be downloaded from the

host system website, from Emerson.com/Rosemount, or from

FieldCommGroup.org.

Quick Start Guide June 2020

6 Emerson.com/Rosemount

2.3 The security and simulate switches

The security and simulate switches are located on the electronics.

Figure 2-4: Transmitter Electronics Board

Aluminum Polished 316 SST

A. Simulate switch

B. Security switch

2.3.1 Setting the security switch

The security switch allows ( ) or prevents ( ) any configuration of the

transmitter.

Note

Default security is off ( ).

Setting the simulate switch

The security switch can be enabled or disabled in the software.

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side.

WARNING

Explosions could result in death or serious injury.

In an explosion-proof/flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

June 2020 Quick Start Guide

Quick Start Guide 7

3. Slide the security switch into the preferred position.

4. Reattach the transmitter housing cover.

Tighten the cover until there is no gap between the cover and

housing to comply with explosion proof requirements.

2.3.2 Setting the simulate switch

The simulate switch is used in conjunction with the transmitter simulate

software to simulate process variables and/or alerts and alarms.

Note

The simulate switch enables or disables simulated alerts and simulated AI

Block status and values. The default simulate switch position is enabled.

•To simulate variables and/or alerts and alarms, the simulate switch must

be moved to the enable position and the software enabled through the

host before installation of the transmitter.

•To disable simulation, the switch must be in the disable position or the

software simulate parameter must be disabled through the host.

Procedure

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side.

WARNING

Explosions could result in death or serious injury.

In an explosion-proof/flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

3. Slide the simulate switch into the preferred position.

4. Reattach the transmitter housing cover.

Tighten the cover until there is no gap between the cover and

housing to comply with explosion proof requirements.

2.4 Connect the wiring and power up

Procedure to connect the wiring and power up the transmitter.

Prerequisites

•Use copper wire of sufficient size to ensure the voltage across the

transmitter power terminals does not drop below 9 Vdc. A minimum of

12 Vdc under normal operating conditions is recommended. Shielded

twisted pair Type A cable is recommended.

Quick Start Guide June 2020

8 Emerson.com/Rosemount

•Power supply voltage can be variable, especially under abnormal

conditions such as when operating on battery backup.

Procedure

1. To power the transmitter, connect the power leads to the terminals

indicated on the terminal block label.

Note

The Rosemount 3051 power terminals are polarity insensitive, which

means the electrical polarity of the power leads does not matter

when connecting to the power terminals. If polarity sensitive devices

are connected to the segment, terminal polarity should be followed.

When wiring to the screw terminals, the use of crimped legs is

recommended.

2. Ensure full contact with terminal block screw and washer. When

using a direct wiring method, wrap wire clockwise to ensure it is in

place when tightening the terminal block screw. No additional power

is needed.

Note

The use of a pin or a ferrule wire terminal is not recommended as the

connection may be more susceptible to loosening over time or under

vibration.

3. Ensure proper grounding. It is important the instrument cable shield

be:

a) Trimmed close and insulated from touching the transmitter

housing.

b) Connected to the next shield if cable is routed through a

junction box.

c) Connected to a good earth ground at the power supply end.

4. If transient protection is needed, refer to section Signal ground

wiring for grounding instructions.

5. Plug and seal unused conduit connections.

6. Reattach the transmitter covers.

a) The covers must only be capable of being released or

removed with the aid of a tool to comply with applicable

ordinary locations requirements.

Figure 2-5: Wiring

Aluminum Polished 316 SST

June 2020 Quick Start Guide

Quick Start Guide 9

A. Minimize distance

B. Trim shield and insulate

C. Protective grounding terminal (do not ground cable shield at the

transmitter)

D. Insulate shield

E. Connect shield back to the power supply ground

2.4.1 Signal ground wiring

Do not run signal wiring in conduit or open trays with power wiring, or near

heavy electrical equipment. Grounding terminations are provided on the

outside of the electronics housing and inside the Terminal Compartment.

These grounds are used when transient protect terminal blocks are installed

or to fulfill local regulations.

Procedure

1. Remove the field terminals housing cover.

2. Connect the wiring pair and ground as indicated in Figure 2-5

a) Trim the cable shield as short as practical and insulate from

touching the transmitter housing.

Note

Do NOT ground the cable shield at the transmitter; if the

cable shield touches the transmitter housing, it can create

ground loops and interfere with communications.

b) Continuously connect the cable shields to the power supply

ground.

c) Connect the cable shields for the entire segment to a single

good earth ground at the power supply.

Quick Start Guide June 2020

10 Emerson.com/Rosemount

Autres manuels pour Rosemount 3051HT

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 248 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Manuel utilisateur

Emerson

Emerson Rosemount 3408 Manuel utilisateur

Emerson

Emerson Rosemount Wireless Permasense WT210 Manuel utilisateur

Emerson

Emerson Rosemount X-well 648 Manuel utilisateur

Emerson

Emerson Rosemount 8782 Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Micro Motion 3700 Manuel utilisateur

Emerson

Emerson Fisher 4200 Series Manuel utilisateur

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Rosemount ET410 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson 6081-P Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount Analytical HART SMART 5081C-HT Manuel utilisateur

Emerson

Emerson Rosemount 644 with HART Protocol Manuel utilisateur

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Rosemount5081 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Fisher 4200 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson ROSEMOUNT 5081-A Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 3408 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur