Emerson Rosemount ET410 Manuel utilisateur

Quick Start Guide

MS-00825-0100-4209, Rev AA

April2023

Rosemount™ Wireless ET410

Corrosion Transmitter

with Rosemount Permasense™

technology

Safety messages

Failure to follow these installation guidelines could result in death or serious injury. Only

qualified personnel should perform the installation.

WARNING

Explosion hazard that could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Review the

approvals section of this manual for any restrictions associated with a safe installation.

Before connecting a CC21 to a sensor, ensure the correct low voltage permits have been

obtained

The power module may be replaced in a hazardous area. Only fit Permasense or Rosemount

approved BP20E power modules.

Magnetic hazard that can result in death or serious injury

This device contains magnets which could be harmful to pacemaker wearers.

The strong magnets used in the magnetic fixture can lead to serious hand injuries unless

personnel are careful.

Electrostatic hazard that can result in death or serious injury

The power module has surface resistivity greater than one gigaohm and must be properly

installed on the wireless device. Care must be taken during transportation to and from the

point of installation to prevent a potential electrostatic charging hazard.

The transmitter’s polymer enclosure has surface resistivity greater than one gigaohm. Care

must be taken during transportation to and from the point of installation to prevent a

potential electrostatic charging hazard.

NOTICE

Shipping considerations for wireless products.

The unit was shipped to you without the power module installed. Remove the power module

prior to any re-shipping.

Each device contains two “D” size primary lithium-thionyl chloride battery cells. Primary

lithium batteries are regulated in transportation by the U.S. Department of Transportation,

and are also covered by IATA (International Air Transport Association), ICAO (International

Civil Aviation Organization), and ARD (European Ground Transportation of Dangerous

Goods). It is the responsibility of the shipper to ensure compliance with these or any other

local requirements. Consult current regulations and requirements before shipping.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or

misconfiguration of end users’ equipment. This could be intentional or unintentional and

needs to be protected against.

Physical security is an important part of any security program and fundamental in protecting

your system. Restrict physical access by unauthorized personnel to protect end users’ assets.

This is true for all systems used within the facility.

Quick Start Guide April2023

2 Emerson.com/Rosemount

Contents

Product overview......................................................................................................................... 5

Preparing for installation............................................................................................................ 8

Mounting the transmitter with a strap................................................................................... 10

Mounting the transmitter with a magnetic fixture................................................................24

Maintenance...............................................................................................................................36

Product certifications................................................................................................................ 41

April2023 Quick Start Guide

Quick Start Guide 3

Quick Start Guide April2023

4 Emerson.com/Rosemount

1 Product overview

A. Antenna

B. Power module

C. Head

D. Strap slot

E. Foot

April2023 Quick Start Guide

Quick Start Guide 5

1.1 What's in the box

Mounting hardware option T01(1) Mounting hardware option B02(2)

Permasense ET410 Sensor (with protective cap)

BP20E Power module

A4 Stainless Steel Strap 138 in (3.5 m) Magnetic mount

Strap tensioner Brackets and fittings (already fitted

to sensor)

Lanyard kit 6.6 ft (2 m) 316 stainless

steel lanyard with looped end and

cable lock.

5 x Lanyard kit (for safety-securing

sensor and magnetic fixture).

(1) Pipe strap up to 40-inch diameter pipe and one strap tensioner.

(2) Magnetic mount, vessel mount

1.2 Required equipment

In order to install the sensor, you need the following equipment from

an IK220 installation kit

•Tablet PC with installation application software

•CC21 interface

WARNING

The tablet PC is not intrinsically safe.

A site-specific permit may be required for its use.

Quick Start Guide April2023

6 Emerson.com/Rosemount

1.3 Required tooling

Separate tooling for Strap option

Tooling is supplied in the IK220 installation kit.

•Tin snips (used to cut the fixing strap to the correct length)

•Flathead screwdriver or wrench and socket (to tighten the fixing

strap)

•2.5 mm hex key (for power module retaining bolts)

Tooling required for magnetic fixture

•Torque wrench with 13mm A/F deep socket

•13mm A/F spanner

•6mm A/F hex key

•2.5mm hex key (for the power module retaining bolts)

1.4 Alternative installation options

Optional tooling

If preferred, an electric screwdriver or wrench may be used instead

of the supplied tools to decrease installation time. This is not

included in IK220 installation kit

April2023 Quick Start Guide

Quick Start Guide 7

2 Preparing for installation

Prerequisites

The Emerson Wireless Gateway should be installed and functioning

properly before commissioning the Rosemount ET410 and powering

it with a BP20E power module.

Note

Wireless devices should be powered up in order of proximity

from the Gateway, beginning with the closest device, then working

outward from the Gateway. This results in a simpler and faster

network formation. Enable Active Advertising on the Gateway to

ensure new devices are able to join the network faster. For more

information, see the Emerson Wireless 1410S Gateway.

Procedure

1. Identify the location where the sensor is to be installed.

2. Ensure that all cladding and insulation is removed around the

circumference of the pipe at the sensor location.

The dimension drawing in Figure 2-1 provides guidance on

how much pipe should be exposed.

Note

Cladding or insulation can be replaced after the sensor

installation is completed, provided that the head of the sensor

remains outside of the insulation. Insulation materials can be

installed around the sensor as desired and according to local

procedures.

Quick Start Guide April2023

8 Emerson.com/Rosemount

Figure 2-1: Transmitter dimensions

Note

Dimensions are in millimeters [Inches].

3. Clean the area where the sensor will touch the pipe to

remove any particles that might keep the transducer away

from the pipe surface or damage the face of the transducer. A

permanent marker may be used to show exactly where each

sensor is to be placed on the pipe.

April2023 Quick Start Guide

Quick Start Guide 9

3 Mounting the transmitter with a strap

3.1 Mounting the transmitter

If you are using the strap mounting option, perform the tasks in this

section.

If you are using the magnetic fixture, skip this section and go to the

Mounting the transmitter with a magnetic fixture.

WARNING

Two people are required for this operation

Personal protective equipment (PPE) of gloves and safety glasses

or full-face visor are recommended.

Cut strap may have sharp edges.

Do not cut the strap while it is under tension because this action

can result in damage or injury.

Procedure

1. Unbox the strap tensioner and the strap from the packaging.

2. Feed the strap into one end of the strap tensioner and using

the screwdriver or wrench and socket provided, turn the screw

on the tensioner until the end of the strap emerges from

under the worm drive (at least 5 turns of the worm-screw are

required).

3. Remove the protective cap from the sensor.

CAUTION

Once the protective cap is removed, the strong magnetic field

at the end of the sensor can suddenly attract other objects,

such as tools. This can cause injury as well as damage to the

sensor.

Only remove the protective cap when necessary and then take

great care. Ensure tools and fastenings are kept away from the

sensor when the cap is removed.

4. Carefully place the sensor on the required location on the

pipe.

5. Check the sensor is on the location correctly and the

thermocouple is in contact with the surface.

Quick Start Guide April2023

10 Emerson.com/Rosemount

Autres manuels pour Rosemount ET410

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson wirelessHART Rosemount Series Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 8712C Guide de configuration

Emerson

Emerson Rosemount 3408 Manuel utilisateur

Emerson

Emerson Rosemount 1066 Manuel utilisateur

Emerson

Emerson Micro Motion 2400S Manuel utilisateur

Emerson

Emerson Rosemount 148 Manuel utilisateur

Emerson

Emerson Micro Motion 2400S Guide rapide

Emerson

Emerson Rosemount 3144P Manuel utilisateur

Emerson

Emerson Fisher 4200 Series Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 5081-T Manuel utilisateur

Emerson

Emerson MICRO MOTION 2700 Guide rapide

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 3051P Manuel utilisateur

Emerson

Emerson Rosemount 2051CF series Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 4600 Manuel utilisateur

Emerson

Emerson Solu Comp Xmt-P-FF/FI Manuel utilisateur

Emerson

Emerson Rosemount 2240S Manuel utilisateur

Emerson

Emerson Rosemount 1408A Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur