Emerson Rosemount Wireless Permasense WT210 Manuel utilisateur

Quick Start Guide

00825-0100-4210, Rev BA

December 2020

Rosemount™ Wireless Permasense

WT210 Corrosion Transmitter

NOTICE

This guide provides basic guidelines for the installation of the Rosemount Wireless Permasense

Corrosion Transmitter. It does not provide instructions for configuration, diagnostics, maintenance,

service, troubleshooting or intrinsically safe (I.S.) installations. Refer to the Rosemount Wireless

Permasense Corrosion Transmitter Reference Manual for more instruction. The manual and this guide

are also available electronically on Emerson.com\Rosemount.

Shipping considerations

Each device contains two “D” size primary lithium-thionyl chloride battery cells. Primary lithium

batteries are regulated in transportation by the U.S. Department of Transportation, and are also

covered by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the responsibility

of the shipper to ensure compliance with these or any other local requirements. Consult current

regulations and requirements before shipping.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of this

manual for any restrictions associated with a safe installation.

Before connecting a CC21 in an explosive atmosphere, make sure the instruments in the segment are

installed in accordance with intrinsically safe or non-incendive field wiring practices.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

This device must be installed to ensure a minimum antenna separation distance of 8-in. (20 cm) from

all persons.

The power module may be replaced in a hazardous area.

The power module has surface resistivity greater than one gigaohm and must be properly installed on

the wireless device. Care must be taken during transportation to and from the point of installation to

prevent a potential electrostatic charging hazard.

Polymer enclosure has surface resistivity greater than one gigaohm.

Care must be taken during transportation to and from the point of installation to prevent a potential

electrostatic charging hazard.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end

users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Quick Start Guide December 2020

2 Emerson.com/Rosemount

Contents

Overview......................................................................................................................................5

Wireless considerations................................................................................................................7

Field communicator connections................................................................................................. 8

Physical installation...................................................................................................................... 9

Commissioning device............................................................................................................... 12

Additional hardware...................................................................................................................17

Product certifications................................................................................................................. 20

December 2020 Quick Start Guide

Quick Start Guide 3

Quick Start Guide December 2020

4 Emerson.com/Rosemount

1 Overview

Figure 1-1: Rosemount Wireless Permasense WT210 Corrosion

Transmitter

A. Antenna

B. Power module

C. Head

D. Waveguide

E. Waveguide spacer

F. Stabilizer

G. Foot

H. Thermocouple

December 2020 Quick Start Guide

Quick Start Guide 5

1.1 Required equipment

Measuring tape

Standard tools (e.g., screwdriver,

wrench, pliers)

IK220

1.2 Hardware not supplied

•Full plain nuts, to suit welded stud thread and metallurgy:

—Thread: M8 or 5/16-in.

—Material: Stainless steel — or suitable other corrosion resistant steel

•Socket for 5/16-in. nuts

1.3 What's in the box

•Rosemount Wireless Permasense WT210 transmitter

•Rosemount Permasense BP20E power module, including two M3 x 16

mm stainless steel retaining bolts

•Stainless steel circular heat shield

•M8 (compatible with 5/16-in. studs) Nord-Lock anti vibration washers,

two per sensor

•Lanyard kit, 316 stainless steel lanyard 6.5 ft. (2 m) in length, gripple

No.2, release key

Quick Start Guide December 2020

6 Emerson.com/Rosemount

2 Wireless considerations

Power up sequence

The Emerson Wireless Gateway should be installed and functioning properly

before any wireless devices are powered. Commission the Rosemount

Wireless Permasense WT210 and install the BP20E power module to power

the device only after the gateway has been installed and functioning. This

results in a simpler and faster network installation. Enabling active

advertising on the Gateway ensures new devices are able to join the network

faster. For more information see the Emerson Wireless 1420 Gateway

Reference Manual.

Antenna position

The antenna is internal to the Rosemount Wireless Permasense WT210

transmitter. The antenna should also be approximately 3 ft. (1 m) from any

large structure, building, or conductive surface to allow for clear

communication to other devices.

December 2020 Quick Start Guide

Quick Start Guide 7

3 Field communicator connections

The CC21 commissioning cable is connected and removed from the

transmitter in the same way as the Rosemount BP20E power module. The

USB connector is plugged in to the tablet PC as shown in Figure 3-1.

Figure 3-1: IK220 Commissioning Kit

A. Tablet PC

B. CC21

C. USB cable plugged into USB port

D. Rosemount Wireless Permasense WT210/ET210 sensor

Quick Start Guide December 2020

8 Emerson.com/Rosemount

4 Physical installation

The corrosion transmitter is connected directly to the piping being

measured.

Mounting considerations

Procedure

1. When mounting sensors on pipe bends and elbows, studs must be

aligned as follows

a) Fit two nuts to the stud, the first at the top of the thread and

the second 15-20 mm down the thread as shown in Figure

4-1.

b) Use M13 deep hex socket with extension bar to bring the

studs parallel to each other and perpendicular to the pipe

surface at the center point between the two studs.

c) Correct stud alignment will ensure the correct orientation of

the nut and washer with respect to the sensor foot.

Figure 4-1: Orientation

2. Observe the sensor contact from the side. As shown in the following

illustrations, check that:

a) Sensor feet are parallel to the pipe surface.

b) Studs are perpendicular to the pipe surface.

c) Sensor tip is in the middle of the two studs.

December 2020 Quick Start Guide

Quick Start Guide 9

Figure 4-2: Improper Installations of the Metal Standoffs

4.1 Mounting

For pipe clamp mounting, see clamp installation guide.

Procedure

1. On painted pipe-work, remove a singular patch of the coating about

1-in. (25 mm) diameter midway between the studs to allow

waveguides to contact pipe directly.

2. On straight pipes, ensure the studs are perpendicular to the sensor

contact point.

3. Apply Loctite® 8009 anti-seize compound to the threads.

4. Record the installation location, sensor ID, MAC address of the

sensor, and power module serial number.

Quick Start Guide December 2020

10 Emerson.com/Rosemount

Autres manuels pour Rosemount Wireless Permasense WT210

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Rosemount 2051G Manuel utilisateur

Emerson

Emerson Micro Motion 800 Manuel utilisateur

Emerson

Emerson CSI 9420 Manuel utilisateur

Emerson

Emerson Rosemount 708 Manuel utilisateur

Emerson

Emerson MICRO MOTION 1500 Manuel utilisateur

Emerson

Emerson Rosemount CX1100 Manuel utilisateur

Emerson

Emerson PT5N FLR Series Manuel utilisateur

Emerson

Emerson Rosemount Oxymitter 4000 Manuel utilisateur

Emerson

Emerson Micro Motion 3500 Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 1066 Manuel utilisateur

Emerson

Emerson Rosemount 1208C Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount CX1100 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 3152 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 3095FC MultiVariable Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 3051N Manuel utilisateur

Emerson

Emerson Bristol 2808 Series Manuel utilisateur

Emerson

Emerson Micro Motion 2400S Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur