Emerson Rosemount 2090P Manuel utilisateur

Quick Start Guide

00825-0100-4108, Rev CA

January 2018

Rosemount™2088, 2090F, and 2090P

Pressure Transmitter

with 4–20 mA HART®and 1–5 Vdc Low Power

HART Protocol (Revision 5 and 7)

00825-0100-4108_RevCA.fm Page 1 Monday, January 15, 2018 6:21 AM

January 2018

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 2088, 2090F, and 2090P Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or intrinsically safe (I.S.) installations. See the Rosemount 2088 Reference Manual for more

information. This manual is also available electronically on Emerson.com/Rosemount.

Explosions could result in death or serious injury.

Installation of these transmitters in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Review the approvals section of the Rosemount

2088 Reference Manual for any restrictions associated with a safe installation.

Before connecting a HART-based communicator in an explosive atmosphere, make sure the instruments in

the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power is applied

to the unit.

Process leaks may cause harm or result in death.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause electrical

shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread form. Entries

marked “M20” are M20 x 1.5 thread form. On devices with multiple conduit entries, all entries will have the same

thread form. Only use plugs, adapters, glands or conduit with compatible thread form when closing these

entries.

Contents

System readiness . . . . . . . . . . . . . . . . . . . . . . . . 3

Mount the transmitter . . . . . . . . . . . . . . . . . . . 4

Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connect the wiring and power up . . . . . . . . . . . 8

Verify transmitter configuration . . . . . . . . . . . . . .10

Trim the transmitter . . . . . . . . . . . . . . . . . . . . . . . . 14

Safety instrumented systems installation . . . . . .16

Product certifications . . . . . . . . . . . . . . . . . . . . . . 17

00825-0100-4108_RevCA.fm Page 2 Monday, January 15, 2018 6:21 AM

Quick Start Guide

January 2018

1.0 System readiness

1.1 Confirm HART revision capability

If using HART-based control or asset management systems, confirm the

HART capability of those systems prior to transmitter installation. Not all

systems are capable of communicating with HART Revision 7 Protocol. This

transmitter can be configured for either HART Revision 5 or 7.

For instructions on how to change the HART revision of the transmitter, see

page 14.

1.2 Confirm correct device driver

Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communication.

Note

The Rosemount 2088, 2090F, and 2090P Transmitters all use Rosemount 2088 Device

Revisions and Drivers.

1. Download the latest DD at Emerson.com or FieldCommGroup.org.

2. In the Browse by Member dropdown menu, select Emerson.

3. Select desired product.

a. Reference Table 1 and Table 2, Find Device Driver Files column to find the

correct device driver.

Table 1. Rosemount 2088 and 2090 with 4–20 mA HART Protocol Device Revisions

and Files

Release

date

Device identification Device driver

identification Review instructions Review

functionality

NAMUR

hardware

revision(1)

1. NAMUR revision is located on the hardware tag of the device. Differences in level 3 changes, signified above by

xx, represent minor product changes as defined per NE53. Compatibility and functionality are preserved and

product can be used interchangeably.

NAMUR

software

revision1

HART

software

revision (2)

2. HART software revisioncan be read using a HART capable configuration tool. Value shown is minimum revision

that could correspond to NAMUR revisions.

HART

universal

revision

Device

revision (3)

3. Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed to enable legacy

device driver revisions to continue to communicate with new HART devices. To access new functionality, the

new device driver must be downloaded. It is recommended to download new device driver files to ensure full

functionality.

Reference manual Change

description(4)(5)

4. HART Revision 5 and 7 selectable, Local Operator Interface (LOI), scaled variable, configurable alarms,

expanded engineering units.

5. Updated electronics hardware design. Intrinsic Safety temperature classification change.

Aug-16 1.1.xx 1.0.xx 3

710

Rosemount 2088

Reference Manual

Rosemount 2090

Reference Manual

(5)

5 9

Jan-13 N/A 1.0.xx 1

710 (4)

5 9

Jan-98 N/A N/A 178 5 3 N/A

00825-0100-4108_RevCA.fm Page 3 Monday, January 15, 2018 6:21 AM

January 2018

Quick Start Guide

2.0 Mount the transmitter

2.1 Rosemount 2088

Mount directly to the impulse line without using an additional mounting bracket

or mount directly to a wall, panel, or 2-in. pipe using an optional mounting

bracket.

2.2 Rosemount 2090P

Mount directly to the process pipe using an existing weld spud, or have a skilled

welder install a new weld spud using a TIG welder. See Rosemount 2088

Reference Manual for complete welding instructions. Improper installation may

result in weld spud distortion. Upright or horizontal position mounting is

recommended to allow proper draining of vent.

2.3 Rosemount 2090F

Mount directly to the process pipe using a standard sanitary fitting (either a 1.5-

or 2-in.Tri-Clamp®connection). Upright or horizontal position mounting is

recommended to allow proper draining of vent.

Table 2. Rosemount 2088 with 1–5 Vdc Low Power HART Protocol Device Revisions

and Files

Release

date

Device identification Device driver

identification Review instructions Review

functionality

NAMUR

hardware

revision(1)

1. NAMUR Revision is located on the hardware tag of the device. Differences in level 3 changes, signified above by

xx, represent minor product changes as defined per NE53. Compatibility and functionality are preserved and

product can be used interchangeably.

NAMUR

software

revision1

HART

software

revision (2)

2. HART software revision can be read using a HART capable configuration tool. Value shown is minimum revision

that could correspond to NAMUR revisions.

HART

universal

revision

Device

revision (3)

3. Device driver file names use device and DD revision, e.g. 10_01. HART Protocol is designed to enable legacy

device driver revisions to continue to communicate with new HART devices. To access new functionality, the new

device driver must be downloaded. It is recommended to download new device driver files to ensure full

functionality.

Reference manual Change

description(4)

4. HART Revision 5 and 7 selectable, LOI, scaled variable, configurable alarms, expanded engineering units.

Jan-13 N/A 1.0.2 3

710 Rosemount 2088

Reference Manual

Rosemount 2090

Reference Manual

(4)

5 9

Jan-98 N/A N/A 178 5 3 N/A

00825-0100-4108_RevCA.fm Page 4 Monday, January 15, 2018 6:21 AM

Quick Start Guide

January 2018

Figure 1. Transmitter Direct Mounting

Figure 2. Panel and Pipe Mounting

2.4 Environmental seal for housing

Thread sealing (PTFE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seal and meets requirements of NEMA®Type

4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

Do not apply torque directly to the electronics housing.

To avoid damage, apply torque only to the hex-shaped

process connection.

Rosemount 2088 Rosemount 2090P Rosemount 2090F

A. 1/2–14 NPT female process connection

B. Vessel wall

C. Weld spud

D. O-ring

E. 11/2- or 2-in. Tri-Clamp connection

Panel mount Pipe mount

2.5 Liquid flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent

valves are oriented upward.

1.5 in.

1.0 in.

00825-0100-4108_RevCA.fm Page 5 Monday, January 15, 2018 6:21 AM

January 2018

Quick Start Guide

2.8 Gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located in the neck of the transmitter, behind the housing. The

vent path is 360° around the transmitter between the housing and sensor (see

Figure 3).

Figure 3. Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

2.6 Gas flow applications

1. Place taps in the top or side of the line.

2. Mount level or above the taps.

2.7 Steam flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Keep the vent path free of any obstruction, including but not limited to paint, dust, and lubrication

by mounting the transmitter so the contaminants can drain away.

00825-0100-4108_RevCA.fm Page 6 Monday, January 15, 2018 6:21 AM

Quick Start Guide

January 2018

3.0 Set the switches

Set alarm and security switch configuration before installation as shown in

Figure 4.

The alarm switch sets the analog output alarm to high or low. Default alarm

is high.

The security switch allows ( ) or prevents ( ) any configuration of the

transmitter. Default security is off ( ).

Use the following procedure to change the switch configuration:

1. If the transmitter is installed, secure the loop, and remove power.

2. Remove the housing cover opposite the field terminal side. Do not remove

the instrument cover in explosive atmospheres when the circuit is live.

3. Slide the security and alarm switches into the preferred position using a small

screwdriver.

4. Reattach the transmitter cover. The cover must be fully engaged to comply

with explosion-proof requirements.

Figure 4. Transmitter Electronics Board

A. Alarm

B. Security

3.1 Electronics board

The Rosemount 2088 and 2090 electronics board should not be tampered with

or removed from the housing as it could cause permanent damage to the

transmitter.

3.2 LOI/LCD display

The LOI/LCD display can be removed and rotated as needed by following the

“Rotating LCD display/LOI display” instructions in the Rosemount 2088

Reference Manual.

Without LCD display With LOI/LCD display

00825-0100-4108_RevCA.fm Page 7 Monday, January 15, 2018 6:21 AM

January 2018

Quick Start Guide

4.0 Connect the wiring and power up

Shielded twisted pair cable should be used for best results. Use 24 AWG or larger

wire that does not exceed 5000 ft. (1500 m) in length. If applicable, install wiring

with a drip loop. Arrange the drip loop so the bottom is lower than the conduit

connections and the transmitter housing.

Figure 5. Wiring the Transmitter (4–20 mA HART)

A. Vdc supply

B. RL≥250 (necessary for HART Communication only)

Figure 6. Wiring the Transmitter (1–5 Vdc Low Power)

A. Power supply

B. Voltmeter

C. Field terminals

Installation of the transient protection terminal block does not provide transient protection

unless the transmitter case is properly grounded.

Do not run signal wiring in conduit or open trays with power wiring, or near heavy electrical

equipment.

Do not connect the powered signal wiring to the test terminals. Power could damage the test

diode in the terminal block.

00825-0100-4108_RevCA.fm Page 8 Monday, January 15, 2018 6:21 AM

Quick Start Guide

January 2018

Use the following steps to wire the transmitter:

1. Remove the housing cover on the FIELD TERMINALS side.

2. Connect the leads as shown in Figure 5 or Figure 6.

3. Tighten the terminal screws to ensure full contact with the terminal block

screw and washer. When using a direct wiring method, wrap wire clockwise

to ensure it is in place when tightening the terminal block screw.

Note

The use of a pin or ferrule wire terminal is not recommended as the connection may be

more susceptible to loosening over time or under vibration.

4. Ground housing to fulfill local grounding regulations.

5. Ensure proper grounding. It is important that the instrument cable shield:

Be trimmed close and insulated from touching the transmitter housing

Be connected to the next shield if cable is routed through a junction box

Be connected to a good earth ground at the power supply end

6. If transient protection is needed, refer to Grounding for transient terminal

block for grounding instructions.

7. Plug and seal unused conduit connections.

8. Replace the housing cover.

Figure 7. Grounding

4.1 Grounding for transient terminal block

Ground termination is provided on the outside of the electronics housing and

inside the terminal compartment. These grounds are used when the transient

protection terminal blocks are installed. It is recommended that 18 AWG or

larger wire is used to connect housing ground to earth ground (internal or

external).

A.Trim shield and insulate

B. Insulate shield

C. Terminate cable shield drain wire to earth ground

D. Internal ground location

E. External ground location

00825-0100-4108_RevCA.fm Page 9 Monday, January 15, 2018 6:21 AM

January 2018

Quick Start Guide

If the transmitter is currently not wired for power up and communication (follow

steps in “Connect the wiring and power up” on page 8. When the transmitter is

properly wired, refer to Figure 7 for internal and external transient grounding

locations.

5.0 Verify transmitter configuration

Verify the configuration using any HART capable configuration tool or LOI -

option code M4. Configuration instructions for a Field Communicator and LOI

are included in this step. See Rosemount 2088 Reference Manual for

configuration instructions using AMS Device Manager.

5.1 Verifying configuration with a Field Communicator

A Rosemount 2088 DD must be installed on the Field Communicator to verify

configuration. Fast Key sequences vary depending on device and DD revisions.

Use the Determine Fast Key sequence table process below to identify the

appropriate Fast Key sequences.

5.2 Field Communicator User Interface

Determine Fast Key sequence table

1. Connect Field Communicator to Rosemount 2088, 2090F, or 2090P.

2. If Home screen matches Figure 8, refer to Table 3 for Fast Key sequences.

3. If Home screen matches Figure 9:

a. Perform Fast Key sequence 1,7,2 to identify Field Revision and HART

Revision.

b. Refer to Table 4 and the appropriate column based on your Field Revision

and HART Revision for Fast Key sequences.

Note

Emerson recommends installing the latest DD to access the complete functionality. Visit

Emerson.com or FieldCommGroup.org.

Figure 8. Traditional Interface

00825-0100-4108_RevCA.fm Page 10 Monday, January 15, 2018 6:21 AM

Autres manuels pour Rosemount 2090P

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Rosemount 2051HT Manuel utilisateur

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson MICRO MOTION 2700 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Series Manuel utilisateur

Emerson

Emerson Rosemount 2051 Manuel utilisateur

Emerson

Emerson Rosemount 326T Manuel utilisateur

Emerson

Emerson Rosemount 1056 Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Rosemount 1199 Manuel utilisateur

Emerson

Emerson Rosemount 1208A Manuel utilisateur

Emerson

Emerson Rosemount 2240S Manuel utilisateur

Emerson

Emerson Magtech LTM-350 Series Manuel

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 1151 Manuel utilisateur

Emerson

Emerson Rosemount ET410 Manuel utilisateur

Emerson

Emerson Rosemount 848T Manuel utilisateur

Emerson

Emerson Rosemount 3051S Series Manuel utilisateur

Emerson

Emerson Rosemount 8712C Guide de configuration

Emerson

Emerson Rosemount 5600 Series Manuel utilisateur

Emerson

Emerson Rosemount 708 Manuel utilisateur

Emerson

Emerson Rosemount 644 with HART Protocol Manuel utilisateur

Emerson

Emerson Rosemount OCX 8800 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur