Emerson Rosemount 3051S Series Manuel utilisateur
Quick Start Guide
00825-0300-4801, Rev CA
December 2018
Rosemount™ 3051S Series Pressure
Transmitter and 3051SF Series Flow
Meter
with Advanced HART® Diagnostics
Safety messages
NOTICE
This guide provides basic guidelines for Rosemount™ 3051S Series Pressure Transmitters. It also
provides the basic electronic guidelines for the Rosemount 3051SFA Reference Manual, Rosemount
3051SFC Reference Manual, and Rosemount 3051SFP Reference Manual. It does not provide
instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Rosemount 3051S
HART Reference Manual for more instruction. This document is also available electronically on
Emerson.com/Rosemount.
WARNING
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the appropriate
local, national, and international standards, codes, and practices. Review the approvals section of this
manual for any restrictions associated with a safe installation.
•Before connecting a handheld communicator in an explosive atmosphere, make sure the
instruments in the loop are installed in accordance with intrinsically safe or non-incendive field
wiring practices.
•In an explosion-proof/flameproof installation, do not remove the transmitter covers when power
is applied to the unit.
•Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous
locations certifications.
•Use appropriately rate Ex adapters, blanking elements, or glands during installation.
•Keep process insulation at least 1 inch (25 mm) from transmitter connection.
Process leaks could result in death or serious injury.
•Install and tighten process connectors before applying pressure.
•To avoid process leaks, only use the O-ring designed to seal with the corresponding flange
adapter.
Electrical shock could cause death or serious injury.
•Avoid contact with the leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Conduit/cable entries
•Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.
Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all
entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a
compatible thread form when closing these entries.
•When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands,
or adapters in cable/conduit entries.
Contents
System readiness........................................... 5
Mount the transmitter................................... 7
Consider housing rotation............................13
Set the switches and jumpers.......................14
Connect wiring and power up...................... 15
Configuration verification............................ 19
Quick Start Guide December 2018
2 Rosemount 3051S Advanced HART
Trim the transmitter.................................... 21
Safety instrumented systems.......................23
Rosemount 3051S/3051SFx/3051S-ERS
Product Certifications.................................. 24
Rosemount 3051S Declaration of Conformity
.................................................................... 40
China RoHS.................................................. 44
December 2018 Quick Start Guide
Quick Start Guide 3
Quick Start Guide December 2018
4 Rosemount 3051S Advanced HART
1 System readiness
1.1 Confirm HART Revision capability
About this task
Not all systems are capable of communicating with HART® Revision 7
protocol. This transmitter can be configured for either HART Revision 5 or 7.
Note
Before installing the transmitter, confirm the correct device driver is loaded
on the host systems.
Procedure
1. If using HART based control or asset management systems, confirm
the HART capability of those systems prior to transmitter installation.
2. Reference the Rosemount™ 3051S Reference Manual for instructions
on how to change the HART revision of the transmitter.
1.2 Confirm correct device driver
Procedure
1. Verify the latest device driver (DD/DTM™) is loaded on your systems to
ensure proper communications.
2. Download the latest device driver at Emerson.com or
FieldCommGroup.org.
1.3 Device revisions and drivers
Table 1-1 provides the information necessary to ensure you have the correct
device driver and documentation for your device.
Table 1-1: Device Revisions and Files
Identify device Find device driver Review
instructio
ns
Review
functiona
lity
Software
release
date
NAMUR
software
revision(1
)
HART
software
revision(2
)
HART
universal
revision
Device
revision(3
)
Manual
documen
t number
Changes
to
software(
4)
Apr-16 1.0.0 20 7 4 00809-01
00-4801
See (4) for
list of
changes.
5 3
December 2018 Quick Start Guide
Quick Start Guide 5
Table 1-1: Device Revisions and Files (continued)
Identify device Find device driver Review
instructio
ns
Review
functiona
lity
Oct-10 N/A 12 5 3 00809-01
00-4801
Added
Power
Advisory,
mA
Output,
Power
Consumpt
ion,
Coefficien
t of
Variation
May-07 N/A 7 5 2 00809-01
00-4801
Update
Statistical
Process
Monitorin
g
Capability
Sep-06 N/A 4, 5, 6 5 1 00809-01
00-4801
N/A
(1) NAMUR software revision is located on the hardware tag of the device. In
accordance with NE53, revisions of the least significant level X (of 1.0.X) do not
change functionality or operation of the device and will not be reflected in the
review functionality column.
(2) HART software revision can be read using a HART capable configuration tool.
(3) Device driver file names use Device and DD Revision, e.g. 10_01. HART Protocol is
designed to enable legacy device driver revisions to continue to communicate with
new HART devices. To access new functionality, the new device driver must be
downloaded. It is recommended to download new device driver files to ensure full
functionality.
(4) HART Revision 5 and 7 selectable.
Quick Start Guide December 2018
6 Rosemount 3051S Advanced HART
2 Mount the transmitter
If the transmitter requires the use of a mounting bracket, use the images for
instructions on how to properly mount the transmitter using the Emerson™
provided mounting brackets. Use only bolts provided with the transmitter or
sold as Emerson spare parts
2.1 Liquid flow applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Mount the transmitter so that the drain/vent valves are oriented
upward.
A
A. Direction of flow
2.2 Gas flow applications
Procedure
1. Place taps in the top or side of the line.
2. Mount beside or above the taps.
A
December 2018 Quick Start Guide
Quick Start Guide 7
A. Direction of flow
2.3 Steam flow applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Fill impulse lines with water.
A
A. Direction of flow
2.4 Mounting brackets
Figure 2-1: Mounting Bracket – Coplanar Flange
Panel mount Pipe mount
Quick Start Guide December 2018
8 Rosemount 3051S Advanced HART
Figure 2-2: Mounting Brackets – Traditional Flange
Panel mount Pipe mount
Figure 2-3: Mounting Brackets – In-line
Panel mount Pipe mount
2.5 Bolting considerations
About this task
If the transmitter installation requires assembly of a process flange, manifold,
or flange adapters, follow these assembly guidelines to ensure a tight seal for
optimal performance characteristics of the transmitter. Only use bolts
supplied with the transmitter or sold by Emerson™ as spare parts. Figure 2-4
illustrates common transmitter assemblies with the bolt length required for
proper transmitter assembly.
December 2018 Quick Start Guide
Quick Start Guide 9
Figure 2-4: Common Transmitter Assemblies
A
4 × 1.75-in.
(44 mm)
D
4 × 1.75-in.
(44 mm)
4 × 2.25-in.
(57 mm)
C
4 ×1.75-in.
(44 mm) 4 ×1.50-in.
(38 mm)
B
4 × 2.88-in.
(73 mm)
A. Transmitter with coplanar flange
B. Transmitter with coplanar flange and optional flange adapters
C. Transmitter with traditional flange and optional flange adapters
D. Transmitter with coplanar flange and optional Rosemount Conventional
Manifold and flange adapters
Note
For all other manifolds, contact Customer Central technical support.
Bolts are typically carbon steel or stainless steel. Confirm the material by
viewing the markings on the head of the bolt and referencing Table 2-1 . If
bolt material is not shown in Table 2-1, contact the local Emerson
representative for more information.
Use the following bolt installation procedure:
Procedure
1. Carbon steel bolts do not require lubrication and the stainless steel
bolts are coated with a lubricant to ease installation. However, no
additional lubricant should be applied when installing either type of
bolt.
2. Finger-tighten the bolts.
3. Torque the bolts to the initial torque value using a crossing pattern.
See Table 2-1 for initial torque value.
4. Torque the bolts to the final torque value using the same crossing
pattern. See Table 2-1 for final torque value.
Quick Start Guide December 2018
10 Rosemount 3051S Advanced HART
Autres manuels pour Rosemount 3051S Series
23
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Emerson Émetteur
Emerson
Emerson Rosemount 2051 Manuel utilisateur
Emerson
Emerson Rosemount 2051G Manuel utilisateur
Emerson
Emerson Rosemount 1199 Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson MICRO MOTION 2700 Manuel du propriétaire
Emerson
Emerson Rosemount 644 Manuel utilisateur
Emerson
Emerson Rosemount OCX 8800 Manuel utilisateur
Emerson
Emerson Micro Motion 3700 Manuel utilisateur
Emerson
Emerson Rosemount 3101 Manuel utilisateur
Emerson
Emerson Rosemount 4600 Manuel utilisateur
Emerson
Emerson MICRO MOTION 2700 Manuel utilisateur
Emerson
Emerson CSI 9420 Manuel utilisateur
Emerson
Emerson Rosemount 3095FB MultiVariable MODBUS Manuel utilisateur
Emerson
Emerson ROSEMOUNT 5081-A Manuel utilisateur
Emerson
Emerson MICRO MOTION 2700 Guide rapide
Emerson
Emerson Rosemount 3051 CF Series Manuel utilisateur
Emerson
Emerson Rosemount 3408 Manuel utilisateur
Emerson
Emerson Rosemount 8750W Manuel utilisateur
Emerson
Emerson Rosemount 3051S Series Mode d’emploi
Emerson
Emerson Rosemount 848T Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
