Danfoss Type CFR Manuel utilisateur

RoomThermostat

User Guide

Type CFR

Temperature setting

Set room temperature on the thermostat dial.

On the right-hand side of the thermostat is a

function switch with 3 possible settings:

The room temperature will be as set

on the thermostat.

The control system must have a CFZ

programmer, put thermostat switch

into this position to engage the pro-

grammer. The temperature will be as

set on the room thermostat, but in ac-

cordance with the consumption pattern

entered.

The heating pattern in the programmer

can be overridden by moving the

switch to or .

The room temperature will be as set

on the thermostat less a setback of

5°C/9°F.

Limitation of the setting range

Behind the dial for temperature setting are two lock-

rings. These can be moved as shown if the thermo-

stat setting range is to be narrowed.

Warning: Changes or modifications to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

(70°F)

FCC ID: PGBTYPE-CFR , CAN 3934104209

This device complies with Part 15 of the FCC Rules and

with RSS-210 of Industry Canada:

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Setback

5°C (9°F)

088R0228

Li 3,6V/1,9Ah

088R0228 DKCD 03/01

Registration field in

CFM

RoomThermostat

Instructions for Installation

Type CFR

Each room thermostat has a unique ID number

preventing conflicts with other thermostats. A single

room thermostat is capable of regulating several

heating outputs, provided these outputs are assigned to

the thermostat.

Assigning thermostats to output(s)

-The installation cable between room thermostat and

CFM (fig. 1) must be connected in assigning each

thermostat to the respective output(s).

-IntheLED array the firstavailable position will flash.

Outputs already assigned will not be lit (fig. 2). By

pressing OK the thermostat will be assigned to that

output. If the room thermostat is to be assigned under

another lit output, scroll to the output bymeansof the+/-

keys,then press OK.

-When the installation cable is removed, the red LED

underneath the battery cover (fig. 1) will flash for at

least one minute (Test mode).

Removal of assigned thermostat

-It is not necessary to have the installation cable in

place when removing an assigned thermostat. Once a

thermostat has been removed, it may be reassigned to

another output.

-Removal of room thermostat is done by pressing OK

for 5 seconds, then the entire LED array will be lit.

Scroll to the specific room thermostat to be removed

with the +/- button,and press OK for 5 seconds. The

thermostat has now been removed.

Test of room thermostat

If a defect in a room thermostat is suspected, the fol-

lowing test may be carried out:

- Set the thermostat to the highest temperature.

- Move the function switch on the side of the room ther-

mostat to a new position.

- If the LED underneath the battery cover (fig. 1) flashes

quickly for 3 minutes, the room thermostat is OK.

Table des matières

Autres manuels Danfoss Thermostat

Danfoss

Danfoss ECtemp 550 Manuel utilisateur

Danfoss

Danfoss DEVI DEVIreg Touch Manuel utilisateur

Danfoss

Danfoss ECtemp 330 Manuel utilisateur

Danfoss

Danfoss 088U0212 Manuel utilisateur

Danfoss

Danfoss HP75-1 Manuel utilisateur

Danfoss

Danfoss REPI Series Manuel utilisateur

Danfoss

Danfoss RA 2000 valve Manuel utilisateur

Danfoss

Danfoss RT1-RF Manuel utilisateur

Danfoss

Danfoss GET B-RF Mode d’emploi

Danfoss

Danfoss living connect Manuel utilisateur

Danfoss

Danfoss FH-WT Manuel utilisateur

Danfoss

Danfoss TP75-RF Manuel utilisateur

Danfoss

Danfoss RET B Mode d'emploi

Danfoss

Danfoss WT-DR Manuel utilisateur

Danfoss

Danfoss EFIT 540 Manuel utilisateur

Danfoss

Danfoss RET230P Manuel utilisateur

Danfoss

Danfoss DEVIreg Smart Manuel utilisateur

Danfoss

Danfoss RET 230 HC-1 Manuel utilisateur

Danfoss

Danfoss RESD Series Manuel utilisateur

Danfoss

Danfoss REP24 Manuel utilisateur

Danfoss

Danfoss 088U0212 Manuel utilisateur

Danfoss

Danfoss TP75M Manuel utilisateur

Danfoss

Danfoss ECtemp Next Plus HW Manuel utilisateur

Danfoss

Danfoss ECtemp Next Plus Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur