Cisco ASA5506-AP702 Manuel utilisateur

Kenton WLAN module

User Guide

Model name: ASA5506-AP702

1 Purpose

The purpose of this document is to give an overall description of the hardware requirements of

the WLAN module used in Kenton project.

1.1 Scope

This document contains the requirements for the subject system and its top-level or architectural

design for an ODM partner. This document should only contain information needed to design

the system, since this document will go to multiple ODM vendors during the RFQ process.

The requirements specify the behavior of the system, both hardware and software. They do not

specify "how" the system will be built except for necessary constraints on the design such as

needed interfaces to other systems or valid constraints on size, shape, processor and memory

utilization, power consumption, etc. The behavior may be described in terms of how the system

enables the end user to perform work (i.e., the functions, performance, quality requirements, etc).

The architectural design describes the components of the system, their individual functions and

performance, and how they interface with each other.

Development considerations such as schedule, cost, development process, and staffing are not

included in this specification.

2 Functional Overview

2.1 System Overview

The Kenton WLAN module is designed f to be a pluggable module assembly to the wireless

version of Kenton Desktop Security Appliance. It will provide the following functionalities:

2x2 100mW

Dual Radios,

802.11n

Internal Antennas

Compliance to standards based Dual Radio, 2x2, 802.11n

 Dual Radio, 2x2, 100mW, Internal Antenna

Shall support Dual Concurrent Radios

 Dual Radio, 2x2, 100mW, Internal Antenna

Shall support limited lifetime warranty

Operating Temp: 0ºC to 40ºC

Storage Temp: -30ºC to 70ºC

Operating Humidity: 10% to 90% Non-condensing

Storage Humidity: 5% to 95% Non-condensing

The PCB must include a printed “Manufactured for Cisco” marking

(using the Cisco Logo as shown in EDCS-775872. The minimum width

of the Cisco logo is ½”. The location is preferable on the top of the PCB,

but the back is acceptable if spacing doesn’t allow it to be on the top. It

cannot be underneath a soldered component (but can be underneath a

mini-PCI card if one exists).

FCC Statement:

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

This device and its antenna(s) must not be co-located with any other transmitters except in

accordance with FCC multi-transmitter product procedures.

Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated

simultaneously without C2P.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in

indoor environment only.

Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap

the 5600 - 5650 MHz band.

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is responsible for the

compliance to all the rules that apply to the product into which this certified RF module is

integrated.

Additional testing and certification may be necessary when multiple modules are used.

20cm minimum distance has to be able to be maintained between the antenna and the

users for the host this module is integrated into. Under such configuration, the FCC

radiation exposure limits set forth for an population/uncontrolled environment can be

satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least

20cm separation with the antenna while this end product is installed and operated. The

end user has to be informed that the FCC radio-frequency exposure guidelines for an

uncontrolled environment can be satisfied. The end user has to also be informed that

any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment. If the size of the end product is smaller than

8x10cm, then additional FCC part 15.19 statement is required to be available in the

users manual: This device complies with Part 15 of FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX

FCC ID: LDKASA-AP702". If the size of the end product is larger than 8x10cm, then the

following FCC part 15.19 statement has to also be available on the label: This device

complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and (2) this device must accept any

interference received, including interference that may cause undesired operation.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d'en compromettre le fonctionnement.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être

exploités. Sélection d'autres canaux n'est pas possible.

This device and its antenna(s) must not be co-located with any other transmitters except in

accordance with IC multi-transmitter product procedures.

Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated

simultaneously without reassessment permissive change.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une

autre antenne ou transmetteur.

Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350

MHz,

5470-5600 MHz and 5650-5725 MHz

Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350

MHz, 5470-5600 MHz et 5650-5725 MHz

The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for

harmful interference to co-channel mobile satellite systems.

les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites

mobiles utilisant les mêmes canaux.

The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and

5470-5725 MHz) to comply with the e.i.r.p. limit.

le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et

5470-5725 MHz doit se conformer à la limite de p.i.r.e.;

Users should also be advised that high-power radars are allocated as primary users (i.e.

priority

users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could

cause interference and/or damage to LE-LAN devices.

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont

désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et

5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs

LAN-EL.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de

distance entre la source de rayonnement et votre corps.

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for

the IC compliance requirement of the end product, which integrates this module.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least

20cm separation with the antenna while this end product is installed and operated. The

end user has to be informed that the IC radio-frequency exposure guidelines for an

uncontrolled environment can be satisfied. The end user has to also be informed that

any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX

IC : 2461B-ASAAP702 ".

Under Industry Canada regulations, this radio transmitter may only operate using an

antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry

Canada. To reduce potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.

Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut

choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne

dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

This radio transmitter (ASA5506-AP702) has been approved by Industry Canada to

operate with the antenna types listed below with the maximum permissible gain and

required antenna impedance for each antenna type indicated. Antenna types not

included in this list, having a gain greater than the maximum gain indicated for that type,

are strictly prohibited for use with this device.

Le présent émetteur radio (ASA5506-AP702) a été approuvé par Industrie Canada pour fonctionner avec

les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour

chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au

gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Antenna list:

Band Ant. Brand Model Name Antenna Type Connector Gain (dBi)

1 WNC EAAH-N32 PIFAAntenna I-PEX 2.97

2.4G 2 WNC EAAH-N32 PIFAAntenna I-PEX 2.97

1 WNC EAAH-N32 PIFAAntenna I-PEX 3.89

5G 2 WNC EAAH-N32 PIFAAntenna I-PEX 3.89

Note: Beamforming Gain=10*Log(2)=3.01dBi

Telec Statement:

5GHz product for indoor use only.

CE Statement:

This equipment complies with EU radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

Table des matières

Autres manuels Cisco Unité de contrôle

Cisco

Cisco Beacon Point Module Manuel

Cisco

Cisco WS-G5484 Manuel utilisateur

Cisco

Cisco 6015 Manuel d'utilisation et d'entretien

Cisco

Cisco FlexWAN Manuel utilisateur

Cisco

Cisco T3 Guide de démarrage rapide

Cisco

Cisco TelePresence MCU 4200 Series Manuel utilisateur

Cisco

Cisco NCS 1010 Feuille d'instructions

Cisco

Cisco ONS 15540 ESPx Mode d’emploi

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuel d'installation et d'exploitation

Cisco

Cisco 7300-1OC12POS-MM Instructions d'utilisation et d'entretien

Cisco

Cisco C3850-NM-4-1G Mode d’emploi

Cisco

Cisco 3110 Manuel utilisateur

Cisco

Cisco Firepower 4112 Manuel

Cisco

Cisco T1 Manuel utilisateur

Cisco

Cisco MEM-CIP-64M Manuel utilisateur

Cisco

Cisco ATUC-4DMT-ISDN Instructions d'utilisation et d'entretien

Cisco

Cisco PA-VXA Series Instructions d'utilisation et d'entretien

Cisco

Cisco NCS 1004 Manuel utilisateur

Cisco

Cisco SM-X-1T3/E3 Manuel utilisateur

Cisco

Cisco CSS 11500 Manuel de service

Cisco

Cisco NM-1CT1 Guide de démarrage rapide

Cisco

Cisco MGX RPM-XF Manuel utilisateur

Cisco

Cisco 3600 Series Guide de démarrage rapide

Cisco

Cisco HPNA Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur