Cisco Firepower 4110 Manuel utilisateur

Installation, Maintenance, and Upgrade

•Install, Remove, and Replace the Network Module, on page 1

•Remove and Replace the Fan Module, on page 4

•Remove and Replace the SSD, on page 6

•Remove and Replace the Power Supply Module, on page 9

•Connect the DC Power Supply Module, on page 13

•Secure the Power Cord on the AC Power Supply Module, on page 19

•Install the FIPS Opacity Shield, on page 22

Install, Remove, and Replace the Network Module

Hot Swapping

Starting with FXOS 2.3.1, the Firepower 10-Gb and 40-Gb network modules (without hardware bypass

support) support hot swapping, but you must hot swap with an identical network module, that is, a network

module with the same PID. See Product ID Numbers for the network module PIDs. You must bring the

network module offline using the appropriate CLI commands before removing the network module from

the chassis so that all network module configuration is saved. See the “Taking a Network Module Offline

or Online” topic in the Security Module/Engine Management chapter in the Cisco FXOS Firepower

Chassis Manager Configuration Guide.

We do not recommend that you remove the network module without bringing it properly offline using

the appropriate CLI commands.

Caution

You must have ROMMON 1.0.10 or later on the Supervisor to support hot swapping. For the ROMMON

upgrade procedure, see the "Firmware Upgrade" topic in the Image Management chapter in the Cisco

FXOS Firepower Chassis Manager Configuration Guide for your software version.

Note

To remove and replace the network modules that do not currently support hot swapping, power off the

chassis, replace the network module, and then power the chassis back on.

Acknowledgment is necessary if you decommission and physically remove a network module and do

not replace it, or if you replace it with another PID. See the "Acknowledging a Security Module/Engine”

Installation, Maintenance, and Upgrade

topic in the Security Module/Engine Management chapter in the Cisco FXOS Firepower Chassis Manager

Configuration Guide.

Safety Warnings

Take note of the following component replacement safety warnings:

Statement 1028—More Than One Power Supply

This unit might have more than one power supply connection. To reduce risk of electric shock, remove

all connections to de-energize the unit.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1073—No User-Serviceable Parts

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1089—Instructed and Skilled Person Definitions

An instructed person is someone who has been instructed and trained by a skilled person and takes the

necessary precautions when working with equipment.

A skilled person or qualified personnel is someone who has training or experience in the equipment

technology and understands potential hazards when working with equipment.

Warning

Statement 1090—Installation by Skilled Person

Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089

for the definition of a skilled person.

Warning

Statement 1091—Installation by an Instructed Person

Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.

See statement 1089 for the definition of an instructed or skilled person.

Warning

Installation, Maintenance, and Upgrade

Install, Remove, and Replace the Network Module

This procedure describes how to install a network module into an empty slot that has never contained a network

module, and how to remove an installed network module and replace it with another network module.

Step 1 To install a new network module for the first time into an empty slot, do the following:

a) Power down the chassis by moving the power switch to the OFF position.

See Rear Panel for more information about the power switch.

b) Follow Steps 4 through 7 to install the new network module.

c) Power on the chassis by moving the power switch to the ON position.

The state for the new network module is OIR Failed.

d) To change the status of the network module to Online, reboot the chassis. See the "Rebooting the Firepower 4100/9300

Chassis" topic in the System Administration chapter in the FXOS Configuration Guide for your software version.

Step 2 To remove and replace an existing network module, do one of the following:

a) Save your configuration.

b) Power down the chassis by moving the power switch to the OFF position (if removing a network module that does

not support hot swapping).

See Rear Panel for more information about the power switch.

c) Bring the network module offline using the appropriate CLI command (if removing a network module that supports

hot swapping). All network module configuration is saved. See the “Taking a Network Module Offline or Online”

topic in the Security Module/Engine Management chapter in the FXOS Configuration Guide for your software version.

d) Continue with Step 3.

Step 3 To remove a network module from the chassis, loosen the captive screw on the lower left side of the network module

and pull out the handle that is connected to the screw. This mechanically ejects the network module from the slot.

Figure 1: Remove the Network Module

Installation, Maintenance, and Upgrade

Install, Remove, and Replace the Network Module

If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;

otherwise, install another network module.

Step 4 To replace a network module, hold the network module in front of the network module slot on the right of the chassis

and pull the network module handle out.

Step 5 Slide the network module into the slot and push it firmly into place until the handle is flush with the front of the network

module.

Step 6 Tighten the captive screw on the lower left side of the network module.

Step 7 Do one of the following:

a) Power up the chassis so that the new network module is recognized (if the new network module does not support hot

swapping).

b) Bring the new network module online using the appropriate CLI command (if the new network module supports hot

swapping). The saved network module configuration is automatically reapplied when the network module is back

online.

If you install a network module that is a different PID than the original network module, the saved

configuration is deleted and the default configuration is applied. You must enter the acknowledge command

to confirm the network module PID change:

Note

What to do next

Follow the procedures in the FXOS Configuration Guide to connect to the network module and make sure

that it has been discovered correctly by the Firepower 4100.

Remove and Replace the Fan Module

You can remove and replace fan modules while the system is running. The air flow moves from front to back.

If you remove a fan or a fan fails, the other fans operate at full speed, which can be noisy.

The system supports operation with a single fan failure (N+1 fan redundancy), but do not run the system for

an extended amount of time without all fan modules installed. Keep removal and replacement time at three

minutes. Remove and replace one fan module at a time.

Note

Safety Warnings

Take note of the following component replacement safety warnings:

Installation, Maintenance, and Upgrade

Remove and Replace the Fan Module

Statement 1028—More Than One Power Supply

This unit might have more than one power supply connection. To reduce risk of electric shock, remove

all connections to de-energize the unit.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1073—No User-Serviceable Parts

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1089—Instructed and Skilled Person Definitions

An instructed person is someone who has been instructed and trained by a skilled person and takes the

necessary precautions when working with equipment.

A skilled person or qualified personnel is someone who has training or experience in the equipment

technology and understands potential hazards when working with equipment.

Warning

Statement 1090—Installation by Skilled Person

Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089

for the definition of a skilled person.

Warning

Statement 1091—Installation by an Instructed Person

Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.

See statement 1089 for the definition of an instructed or skilled person.

Warning

Step 1 To remove a fan module, face the rear of the chassis, and grasp the handle of the fan module.

Step 2 Squeeze the handle to disengage the latches on the left and right of the fan module.

Step 3 Pull the fan module out of the chassis.

Installation, Maintenance, and Upgrade

Remove and Replace the Fan Module

Figure 2: Remove the Fan Module

Step 4 To replace a fan module, hold the fan module in front of the fan slot.

Step 5 Push the fan module into the chassis until it is properly seated and the latches snap into place.

If the system is powered on, listen for the fans. You should immediately hear the fans operating. If you do not hear the

fans, make sure the fan module is inserted completely into the chassis and the faceplate is flush with the outside surface

of the chassis.

Step 6 Verify that the fan is operational by checking the fan module LED. See Front Panel LEDs for a description of the fan

LEDs.

Remove and Replace the SSD

Although the hardware supports removing and replacing SSDs while the system is running, the software does

not currently support hot swapping. You must power down the chassis to remove and replace SSDs.

If your Firepower 4100 is running Firepower Threat Defense software, we recommend that you upgrade to

the latest version to take advantage of software updates that enhance SSD management performance and

longevity.

Note

You storage SSD must be installed in slot 1 and must be present. Only an optional MSP can be installed in

the second SSD slot (SSD slot 2). The MSP stores threat detection results for use in future analysis. It supports

Installation, Maintenance, and Upgrade

Remove and Replace the SSD

the Advanced Malware Protection software feature. The MSP is supported beginning in FXOS 2.0.1. It is

used as both storage and as the Malware application repository. RAID is not supported.

Do not switch the two SSDs. The storage SSD must be installed in slot 1. The optional MSP SSD must be

installed in slot 2. If you remove it and install it in slot 1, all stored file capture data is lost.

Caution

Safety Warnings

Take note of the following component replacement safety warnings:

Statement 1028—More Than One Power Supply

This unit might have more than one power supply connection. To reduce risk of electric shock, remove

all connections to de-energize the unit.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1073—No User-Serviceable Parts

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1089—Instructed and Skilled Person Definitions

An instructed person is someone who has been instructed and trained by a skilled person and takes the

necessary precautions when working with equipment.

A skilled person or qualified personnel is someone who has training or experience in the equipment

technology and understands potential hazards when working with equipment.

Warning

Statement 1090—Installation by Skilled Person

Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089

for the definition of a skilled person.

Warning

Installation, Maintenance, and Upgrade

Remove and Replace the SSD

Statement 1091—Installation by an Instructed Person

Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.

See statement 1089 for the definition of an instructed or skilled person.

Warning

Step 1 Save your configuration.

Step 2 Power down the chassis by moving the power switch to the OFF position. See Features for more information about the

power switch.

Step 3 To remove an SSD, face the front of the chassis, loosen the two captive screws on the SSD, and gently pull it out of slot

1 of the chassis.

Figure 3: Remove the SSD

Step 4 To replace the SSD, make sure the power switch is still in the OFF position, and then hold the SSD in front of slot 1 and

push it in gently until it is seated.

Step 5 To install the MSP SSD, make sure the power switch is still in the OFF position and then remove the blank faceplate in

slot 2 by loosening the captive screws on either side of the faceplate.

Step 6 Hold the MSP SSD in front of slot 2 and push it in gently until it is seated.

Do not switch the two SSDs. Only the optional MSP SSD can be installed in slot 2. If you remove it and install

it in slot 1, all stored file capture data is lost.

Caution

Step 7 Tighten the captive screws on either side of the SSD.

Step 8 Verify that the SSD is operational by checking the SSD LED. See Front Panel LEDs for a description of the fan LEDs.

Installation, Maintenance, and Upgrade

Remove and Replace the SSD

Remove and Replace the Power Supply Module

You can remove and replace power supply modules while the system is running.

Safety Warnings

Take note of the following power and component removal safety warnings:

Statement 347—Failure to Secure the Expansion Module

To reduce the risk of electric shock, secure the modules with the provided screws.

Warning

Statement 1003—DC Power Disconnection

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Warning

Statement 1005—Circuit Breaker

This product relies on the building’s installation for short-circuit (overcurrent) protection. To reduce risk

of electric shock or fire, ensure that the protective device is rated not greater than:

AC: 20A

DC: 40A

Warning

Statement 1017—Restricted Area

This unit is intended for installation in restricted access areas. Only skilled, instructed, or qualified

personnel can access a restricted access area.

Warning

Statement 1018—Supply Circuit

To reduce risk of electric shock and fire, take care when connecting units to the supply circuit so that

wiring is not overloaded.

Warning

Statement 1022—Disconnect Device

To reduce risk of electric shock and fire, you must incorporate a readily accessible two-poled disconnect

device in the fixed wiring.

Warning

Installation, Maintenance, and Upgrade

Remove and Replace the Power Supply Module

Statement 1025—Use Copper Conductors Only

To reduce risk of fire, use copper conductors only.

Warning

Statement 1028—More Than One Power Supply

This unit might have more than one power supply connection. To reduce risk of electric shock, remove

all connections to de-energize the unit.

Warning

Statement 1029—Blank Faceplates and Cover Panels

Blank faceplates and cover panels serve three important functions: they reduce the risk of electric shock

and fire, they contain electromagnetic interference (EMI) that might disrupt other equipment, and they

direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates,

front covers, and rear covers are in place.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1073—No User-Serviceable Parts

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1046—Installing or Replacing the Unit

To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always

be made first and disconnected last.

Warning

Installation, Maintenance, and Upgrade

Remove and Replace the Power Supply Module

Autres manuels pour Firepower 4110

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Unité de contrôle

Cisco

Cisco MEM-NP8F Series Guide de démarrage rapide

Cisco

Cisco TelePresence Touch10 Manuel utilisateur

Cisco

Cisco T1 Manuel utilisateur

Cisco

Cisco NM-1CT1 Guide de démarrage rapide

Cisco

Cisco GS7000 Mode d'emploi

Cisco

Cisco CGM-WPAN-OFDM-FCC Manuel utilisateur

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuel d'installation et d'exploitation

Cisco

Cisco Firepower 4112 Manuel

Cisco

Cisco EHWIC-3G-EVDO Manuel utilisateur

Cisco

Cisco GS7000 Manuel de l'opérateur

Cisco

Cisco TelePresence MCU 4200 Series Manuel utilisateur

Cisco

Cisco 3600 Series Guide de démarrage rapide

Cisco

Cisco 7300-1OC12POS-MM Instructions d'utilisation et d'entretien

Cisco

Cisco Catalyst 5000 Series Manuel utilisateur

Cisco

Cisco FlexWAN Manuel utilisateur

Cisco

Cisco CSS 11500 Manuel de service

Cisco

Cisco MGX RPM-XF Manuel utilisateur

Cisco

Cisco WS-G5484 Manuel utilisateur

Cisco

Cisco ONS 15200 Manuel utilisateur

Cisco

Cisco NM-1E2W Guide de démarrage rapide

Cisco

Cisco LightStream 1010 Guide de démarrage rapide

Cisco

Cisco SCE8000 GBE Manuel utilisateur

Cisco

Cisco MEM-CIP-64M Manuel utilisateur

Cisco

Cisco T3 Guide de démarrage rapide

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur