Cisco WS-G5484 Manuel utilisateur

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Gigabit Interface Converter (GBIC) Module and

Small Form-Factor Pluggable (SFP) GBIC Module

Installation Information and Specifications

GBIC Product Numbers: WS-G5484, WS-G5486, WS-G5487, CWDM-GBIC-1470=, CWDM-GBIC-1490=,

CWDM-GBIC-1510=, CWDM-GBIC-1530=, CWDM-GBIC-1550=, CWDM-GBIC-1570=, CWDM-GBIC-1590=,

CWDM-GBIC-1610=

SFP Product Numbers: SFP-GE-F=, SFP-GE-S=, SFP-GE-L=, SFP-GE-Z=, GLC-SX-MM=, GLC-LH-SM=, GLC-ZX-SM=,

GLC-T=, CWDM-SFP-1470=, CWDM-SFP-1490=, CWDM-SFP-1510=, CWDM-SFP-1530=, CWDM-SFP-1550=,

CWDM-SFP-1570=, CWDM-SFP-1590=, CWDM-SFP-1610=.

Revision History Table

The Document Revision History table below, beginning with OL-5007-06, records technical changes to

this document.

Introduction

This document provides information about Gigabit Interface Converter (GBIC) modules and small

form-factor (SFP) GBIC modules on the Cisco 7200VXR routers, the Cisco 7201 router, the Cisco 7301

router, the Cisco 7304 router, the Cisco 7401ASR router, the Cisco 7500 series routers, the Cisco 7600

series routers, the Cisco 10008 router, the Cisco 12000 series routers, and the Cisco uBR7246VXR cable

Document Version Date Change Summary

OL-5067-08 August, 2008 This version adds SFP module SFP-GE-F information.

OL-5067-07 April, 2007 This version adds Cisco 7201 support.

OL-5067-06 December, 2006 This version adds SFP module SFP-GE-S, SFP-GE-L,

and SFP-GE-Z information.

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

Contents

router and Cisco uBR10012 cable router. The GBIC modules and SFP modules are input/output devices

that plug into a Gigabit Ethernet (GE) port, linking the port with a 1000BASE-X fiber-optic network.

The devices are used on Cisco platforms that have Gigabit Ethernet interfaces.

Also see the documentation that shipped with the GBIC module or SFP module or the installation guide

for your router, I/O controller, processor engine, or port adapter.

Contents

This document contains the following sections:

•Related Documentation, page 2

•GBIC Module and SFP Module Overview, page 4

•Cisco 1000BASE-T SFP Modules, page 9

•CWDM GBIC Module and SFP Module Description and Information, page 9

•Mode-Conditioning Patch Cord Description, page 13

•Installation Prerequisites, page 15

•Installing and Removing the GBIC Module or SFP Module, page 16

•Installing a GBIC Module, page 17

•Installing an SFP Module, page 18

•Installing the GBIC Module or SFP Module Interface Cables, page 20

•Fiber-Optic Cleaning Information, page 22

•Obtaining Documentation and Submitting a Service Request, page 23

Related Documentation

Cisco 7401ASR Router Documentation Roadmap

•Cisco 7500 series routers:

Cisco 7500 Series Routers Documentation Roadmap

•Cisco 7600 series routers:

–

Cisco 7600 Series Internet Router Installation Guide

–

Cisco 7609 Internet Router Installation Guide

•Cisco 10000 ESR routers:

Cisco 10000 Series Routers Line Card Hardware Installation Guide

Cisco 12000 series routersCisco 12000 Series Internet Router Install and Upgrade Guides

•Cisco uBR7246VXR cable router and Cisco uBR10012 cable router:

–

Cisco uBR10012 Universal Broadband Router Hardware Installation Guide

–

Cisco uBR7246VXR Universal Broadband Router Quick Start Guide

•For international agency compliance, safety, and statutory information for WAN interfaces:

–

Site Preparation and Safety Guide

–

Regulatory Compliance and Safety Information for the Cisco 7200 Series Routers

–

Regulatory Compliance and Safety Information for the Cisco 7301 Internet Router

–

Regulatory Compliance and Safety Information for Cisco 7304 Internet Router

–

Regulatory Compliance and Safety Information for the Cisco 7401ASR Internet Router

–

Regulatory Compliance and Safety Information for Cisco 7500 Series Routers

–

Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers

–

Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers

•To view Cisco documentation or obtain general information about the documentation, refer to the

“Obtaining Documentation and Submitting a Service Request” section on page 23.

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

GBIC Module and SFP Module Overview

The following topics are in this section:

•SFP and GBIC Short Wavelength Modules, page 7

•SFP and GBIC Long Wavelength Modules, page 7

•SFP and GBIC Extended Wavelength Modules, page 7

•GBIC Module and SFP Module Cabling and Connection Equipment, page 8

The GBIC module and SFP module are input/output (I/O) devices that plug into a Gigabit Ethernet port,

linking the port with a 1000BASE-X fiber-optic network. A GBIC module is shown in Figure 1, and an

SFP module in Figure 2.

Note Other GBIC modules and SFP modules exist for technologies other than Gigabit Ethernet. However, the

information in this document is for GBIC modules and SFP modules that plug in to only Gigabit Ethernet

ports.

Figure 1 GBIC Module

Figure 2 SFP Module

The GBIC module and SFP module have a receiver port (RX) and a transmitter port (TX) that make up

one optical interface.

1Receiver (RX) 2Transmitter (TX)

101308

1 2

101310

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

GBIC Module and SFP Module Overview

The following tables provide information and specifications:

•Table 1, “GBIC Module and SFP Module Options”

•Table 2, “GBIC Module and SFP Module Transmit Power, Receive Power, and Power Budget”

•Table 3, “SFP-GE-F, SFP-GE-L, SFP-GE-S, and SFP-GE-Z Module Transmit Power, Receive

Power, and Power Budget”

•Table 4, “GBIC Module Specifications”

•Table 5, “SFP Module Specifications”

Table 1 GBIC Module and SFP Module Options

GBIC Module

Product Number

SFP Module

Product Number GBIC Module or SFP Module Description

WS-G5484 GLC-SX-MM Short wavelength

(1000BASE-SX)

Contains a Class 1 laser of 850 nm for

1000BASE-SX (short wavelength) applications.

WS-G5486 GLC-LH-SM Long wavelength/long haul

(1000BASE-LX/LH)

Contains a Class 1 laser of 1300 nm for

1000BASE-LX/LH (long wavelength)

applications.

WS-G5487 GLC-ZX-SM Extended distance

(1000BASE-ZX)

Contains a Class 1 laser of 1550 nm for

1000BASE-ZX (extended wavelength)

applications.

Table 2 GBIC Module and SFP Module Transmit Power, Receive Power, and Power Budget

GBIC Module

and SFP Module

Transmit Power Receive Power Power Budget

Minimum Maximum Minimum Maximum

WS-G5484 and

GLC-SX-MM

–9.5 dB1

1. For fiber types 50/125 μm, NA = 0.20 fiber and 62.5/125 μm, NA = 0.275 fiber.

–3 dB1–17 dB 0 dB 7.5 dB2

2. For fiber types 50/125 μm MMF and 62.5/125 μm MMF.

WS-G5486 and

GLC-LH-SM

–9.5 dB3

–11.5 dB4

3. For fiber types 9/125 μm SMF.

4. For fiber types 62.5/125 μm MMF and 50/125 μm MMF.

–3 dB5

5. For fiber types 9/125 μm SMF, 62.5/125 μm MMF, and 50/125 μm MMF.

–20 dB –3 dB 8.5 dB6and 10.5 dB7

6. For fiber types 50/125 μm MMF and 62.5/125 μm MMF.

7. For fiber type 10 μm SMF.

Note For more information on Link budget, refer to the following Cisco document:

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd803

3f885.html

WS-G5487 and

GLC-ZX-SM

0 dB 5.2 dB –24 dB –3 dB –24 dB

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

GBIC Module and SFP Module Overview

Table 3 provides power budget information for the SFP-GE-F, SFP-GE-L, SFP-GE-S, and SFP-GE-Z

modules.

Table 4 lists the GBIC module physical specifications and Table 5 lists the SFP module physical

specifications.

Table 3 SFP-GE-F, SFP-GE-L, SFP-GE-S, and SFP-GE-Z Module Transmit Power, Receive Power, and Power Budget

SFP Modules Transmit Power Receive Power Power Budget

Minimum Maximum Minimum Maximum

SFP-GE-F=

For 50/125 cabling

For 62.5/125 cabling

-23.5

-20

-14

-33.5

-11.8

10 dB

13.5 dB

SFP-GE-L -9.5 dB1

-11.5 dB2

1. For fiber types 9/125 mm SMF.

2. For fiber types 62.5/125 mm MMF and 50/125 mm MMF.

-3 dB3

3. For fiber types 9/125 mm SMF, 62.5/125 mm MMF, and 50/125 mm MMF.

-20 dB -3 dB 8.5 dB4 and 10.5 dB5

4. For fiber types 50/125 mm MMF and 62.5/125 mm MMF.

5. For fiber type 10 mm SMF.

SFP-GE-S -9.5 dB6

6. For fiber types 50/125 mm, NA = 0.20 fiber and 62.5/125 mm, NA = 0.275 fiber.

-3 dB -17 dB 0 dB 7.5 dB7

7. For fiber types 50/125 mm MMF and 62.5/125 mm MMF.

SFP-GE-Z 0 dB 5 dB -23 dB 0 dB -24 dB

Table 4 GBIC Module Specifications

Specification Description

Dimensions (H x W x D) 0.39 in. x 1.18 in. x 2.56 in.

(1 cm x 3 cm x 6.5 cm)

Connectors Multimode fiber-optic: SC-type connector

Single-mode fiber-optic: SC-type connector

Wavelength WS-G5484: 850 nm

WS-G5486: 1300 nm

WS-G5487: 1550 nm

Cabling distance

(maximum)

WS-G5484: 1804 feet (550 m)

WS-G5486: 6.2 miles (10 km)

WS-G5487: 43.5 to 62.1 miles (70 to 100 km)

Table 5 SFP Module Specifications

Specification Description

Dimensions (H x W x D) 0.33 in x 0.53 in x 2.22 in (8.5 mm x 13.4 mm x

56.5 mm)

Connectors Multimode fiber-optic: LC-type connector

Single-mode fiber-optic: LC-type connector

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

GBIC Module and SFP Module Overview

SFP and GBIC Short Wavelength Modules

The 1000BASE-SX (short wavelength) GBIC module operates on standard multimode fiber-optic link

spans of up to 1804 feet (550 m). (See Table 6.)

The 100BASE-FX SFP module is a hot-swappable device that plugs into a Gigabit Ethernet SFP port. It

provides full-duplex 100-Mbps connectivity over multimode fiber (MMF) infrastructures. The

100BASE-FX SFP operates on ordinary MMF optical link spans of up to 1.2428 miles (2 km) in length.

SFP and GBIC Long Wavelength Modules

The 1000BASE-LX/LH (long wavelength/long haul) GBIC module interfaces fully comply with the

IEEE 802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach

6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard.

SFP and GBIC Extended Wavelength Modules

The 1000BASE-ZX (extended wavelength) GBIC module operates on ordinary single-mode fiber-optic

link spans of up to 43.5 miles (70 km). Link spans of up to 62.1 miles (100 km) are possible using

premium single-mode fiber or dispersion-shifted single-mode fiber (premium single-mode fiber has a

lower attenuation per unit length than ordinary single-mode fiber; dispersion-shifted single-mode fiber

has both lower attenuation and less dispersion).

The 1000BASE-ZX GBIC module must be coupled to single-mode fiber-optic cable, which is the type

of cable typically used in long-haul telecommunications applications. The 1000BASE-ZX GBIC module

will not operate correctly when coupled to multimode fiber, and it is not intended to be used in

environments where multimode fiber is frequently used (for example, building backbones, or horizontal

cabling).

The 1000BASE-ZX GBIC module is intended to be used as a Physical Medium Dependent (PMD)

component for Gigabit Ethernet interfaces found on various switch and router products. It operates at a

signaling rate of 1250 Mbaud, transmitting and receiving 8B/10B encoded data.

When shorter lengths of single-mode fiber are used, it may be necessary to insert an in-line optical

attenuator in the link to avoid overloading the receiver.

•Insert a 10-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port

on the 1000BASE-ZX GBIC module at each end of the link whenever the fiber-optic cable span is

less than 15.5 miles (25 km).

Wavelength GLC-SX-MM: 850 nm

GLC-LH-SM: 1300 nm

GLC-ZX-SM: 1550 nm

GLC-GE-FX: 1300 nm

Cabling distance

(maximum)

GLC-SX-MM: 1804 feet (550 m)

GLC-LH-SM: 6.2 miles (10 km)

GLC-ZX-SM: 43.5 to 62.1 miles (70 to 100 km)

GLC-GE-FX: 1.2428 miles (2 km)

Table 5 SFP Module Specifications (continued)

Specification Description

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

GBIC Module and SFP Module Overview

•Insert a 5-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port on

the 1000BASE-ZX GBIC module at each end of the link whenever the fiber-optic cable span is equal

to or greater than 15.5 miles (25 km) but less than 31 miles (50 km).

GBIC Module and SFP Module Cabling and Connection Equipment

The GBIC module port is a 1000-Mbps optical interface in the form of an SC-type duplex port (see

Figure 1) that supports IEEE 802.3z interfaces compliant with the 1000BASE-X standard.

Table 6 provides cabling specifications for the GBIC modules and SFP modules that you install in

Gigabit Ethernet devices. Note that all GBIC module ports have SC-type connectors and all SFP ports

have LC-type connectors.

The minimum cable distance for the WS-G5484 or GLC-SX-MM and WS-G5486 or GLC-LH-SM

(multimode fiber [MMF] and single-mode fiber [SMF]) is 6.5 feet (2 m), and the minimum link distance

for the WS-G5487 or GLC-ZX-SM is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of

the link. Without attenuators, the minimum link distance for the WS-G5487 or GLC-ZX-SM is 24.9

miles (40 km).

Table 6 GBIC and SFP Module Port Cabling Specifications

GBIC Module SFP Modules

Wavelength

(nm) Fiber Type

Core Size

(micron)

Modal

Bandwidth

(MHz-km)

Maximum

Cable Distance

WS-G5484 or

GLC-SX-MM

SFP-GE-S or

GLC-SX-MM

850 MMF1

1. Multimode fiber (MMF) only.

62.5 160 722 ft (220 m)

62.5 200 902 ft (275 m)

50.0 400 1640 ft (500 m)

50.0 500 1804 ft (550 m)

WS-G5486 or

GLC-LH-SM

SFP-GE-L or

GLC-LH-SM

1300 MMF2and

SMF

2. A mode-conditioning patch cord is required.

When using the WS-G5486 or GLC-LH-SM with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord between the GBIC module

or SFP module and the MMF cable on both the transmit and the receive ends of the link when link distances are greater than 984 ft (300 m).

We do not recommend using the WS-G5486 or GLC-LH-SM and MMF with no patch cord for very short link distance (tens of meters). The result could

be an elevated bit error rate (BER).

62.5 500 1804 ft (550 m)

50.0 400 1804 ft (550 m)

50.0 500 1804 ft (550 m)

9/10 — 6.2 miles (10 km)

WS-G54873or

GLC-ZX-SM

SFP-GE-Z or

GLC-ZX-SM

1550 SMF 9/10 — 43.5 miles

(70 km)

SMF48 — 62.1 miles

(100 km)

GLC-GE-100FX SFP-GE-F 1270 (min),

1300 (avg),

1380 (max)

MMF 62.5

62.5

50.0

500 1.4 miles (6562

ft)

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

Cisco 1000BASE-T SFP Modules

Note The 1000BASE-ZX GBIC module and SFP modules provide an optical power budget of 21.5 dB. You

should measure your cable plant with an optical loss test set to verify that the optical loss of the cable

plant (including connectors and splices) is less than or equal to 21.5 dB. The optical loss measurement

must be performed with a 1550-nm light source.

Cisco 1000BASE-T SFP Modules

The 1000BASE-T (GLC-T) SFP module is compliant with IEEE 802.3:2000 and plugs into a standard

Gigabit Ethernet SFP module port. It operates on standard Category 5 wiring and has an RJ-45

connector.

See your router installation and configuration guide to determine which routers support the GLC-T SFP

module.

CWDM GBIC Module and SFP Module Description and

Information

Coarse Wavelength-Division Multiplexing (CWDM) GBIC modules and Coarse Wavelength-Division

Multiplexing (CWDM) SFP modules are supported on a variety of Cisco products. For more

information, see the Cisco CWDM GBIC Compatibility Matrix and the Cisco Coarse

Wavelength-Division Multiplexing SFP Compatibility Matrix.

3. You can have a maximum of 12 1000BASE-ZX GBIC modules or SFP modules per system to comply with EN55022 Class B and 24 1000BASE-ZX

GBIC modules or SFP modules per system to comply with FCC Class A regulations.

4. Dispersion-shifted single-mode fiber-optic cable.

Table 7 GLC-T SFP Module Specifications

Specification Description

Dimensions (H x W x D) .055 in. x .054 in. x 2.8 in (14.0 mm. x 13.7 mm.

x 71.1 mm)

Cabling Distance (maximum) 328 feet (100 m)

Power consumption 1.1W

Product number GLC-T=

Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications

OL-5067-08

CWDM GBIC Module and SFP Module Description and Information

Figure 3 CWDM GBIC Module

Figure 4 CWDM SFP Module

The Cisco CWDM GBIC module and SFP modules enables the transport of up to eight channels (Gigabit

Ethernet over single-mode fiber strands. (They also support the transport of up to eight channels [Fiber

Channel] over single-mode strands, although Fiber Channel is not discussed in this document.) Cisco

CWDM GBIC modules have SC-type connectors, and Cisco CWDM SFP modules have LC-type

connectors. They are compatible with 1000BASE-X standard as specified in IEEE 802.3z. The Cisco

CWDM GBUC modules and SFP modules are passive and require no power nor configuration. The Cisco

CWDM modules support online insertion and removal (OIR).

1Color band on label 5Optical bore dust plug

2Alignment groove 6Receive optical bore

3Spring clip 7Color dot

4Transmit optical bore

SINGLE-MODE

1000BASE-CWDM GBIC

CWDM-GBIC-1550=

84472

1Color arrow on label 4Color coded bale clasp

2Receive optical bore 5Optical bore dust plug

3Transmit optical bore

94071

CWDM-SFP-1470-2G

Class 1 21CFR1040.10

LN#50 7/01 03-13

S/N: OH1233456

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Unité de contrôle

Cisco

Cisco ATUC-4DMT-ISDN Instructions d'utilisation et d'entretien

Cisco

Cisco NM-1E2W Guide de démarrage rapide

Cisco

Cisco ASA5506-AP702 Manuel utilisateur

Cisco

Cisco LightStream 1010 Guide de démarrage rapide

Cisco

Cisco CSS 11500 Manuel de service

Cisco

Cisco TelePresence MCU 4500 Series Manuel utilisateur

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuel d'installation et d'exploitation

Cisco

Cisco MEM-NP8F Series Guide de démarrage rapide

Cisco

Cisco Catalyst 9400 Series Manuel d'installation et d'exploitation

Cisco

Cisco Firepower 4112 Manuel

Cisco

Cisco Catalyst WS-X3001 Manuel de l'opérateur

Cisco

Cisco Catalyst 3110G Manuel

Cisco

Cisco PA-4T+ Instructions d'utilisation et d'entretien

Cisco

Cisco FlexWAN Manuel utilisateur

Cisco

Cisco ONS 15540 ESPx Mode d’emploi

Cisco

Cisco Catalyst 5000 Series Manuel utilisateur

Cisco

Cisco 3600 Series Guide de démarrage rapide

Cisco

Cisco 7300-1OC12POS-MM Instructions d'utilisation et d'entretien

Cisco

Cisco WS-SVC-WISM2-1-K9 Guide de démarrage rapide

Cisco

Cisco GS7000 Mode d'emploi

Cisco

Cisco TelePresence MCU 4200 Series Manuel utilisateur

Cisco

Cisco NCS 1010 Feuille d'instructions

Cisco

Cisco Firepower 4110 Manuel utilisateur

Cisco

Cisco 3110 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur