Cisco ONS 15540 ESPx Mode d’emploi
CHAPTER
2-1
Cisco ONS 15540 ESPx Hardware Installation Guide
78-16436-01
2
Installing the Cisco ONS 15540 ESPx
This chapter describes the installation procedures for the Cisco ONS 15540 ESPx
chassis and its components. This chapter includes the following sections:
•Before Installing, page 2-2
•Rack-Mounting the Chassis, page 2-3
•Installing the Chassis, page 2-6
•Installing the Drawers, page 2-10
•Installing the Adapters in the Cross Connect Panels, page 2-12
•Installing the Vertical Cable Guides, page 2-16
•Grounding the Chassis, page 2-18
•Installing and Removing Motherboards and Processor Cards, page 2-21
•Installing and Removing Modules, page 2-23
•Installing and Removing the Fan Assembly, page 2-34
•Powering Up the Shelf, page 2-39
•Using Y-Cable, page 2-60
Note Before you install, operate, or service the system, read the Regulatory
Compliance and Safety Information for the Cisco ONS 15500 Series for important
safety information you should know before working with the system.
Chapter 2 Installing the Cisco ONS 15540 ESPx
Before Installing
2-2
Cisco ONS 15540 ESPx Hardware Installation Guide 78-16436-01
Note To ensure that your hardware is supported by your release of Cisco IOS software,
see the “New and Changed Information” section on page xii. Also refer to the
“Hardware Supported” section of the latest release notes for the
Cisco ONS 15540 ESPx.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the
card. Do not directly touch the backplane with your hand or any metal tool, or
you could shock yourself.
Before Installing
Before you install the chassis, you must complete the following tasks:
•Unpack and inspect the chassis.
•Maintain a network record.
•Mount the chassis.
Caution Use extreme care when removing or installing connectors so you do not damage
the connector housing or scratch the end-face surface of the fiber. Always install
protective covers or dust covers on unused or disconnected components to prevent
contamination. Always clean fiber connectors before installing them.
Unpacking and Inspecting the Cisco ONS 15540 ESPx
The Cisco ONS 15540 ESPx ships with 19-inch mounting brackets. The chassis
is thoroughly inspected before shipment. If any damage has occurred during
transportation or if any item is missing, notify your Cisco customer service
representative immediately.
Upon receipt, inspect the equipment as follows:
Step 1 Take inventory.
2-3
Cisco ONS 15540 ESPx Hardware Installation Guide
78-16436-01
Chapter 2 Installing the Cisco ONS 15540 ESPx Rack-Mounting the Chassis
Compare the equipment inside with the packing slip and the equipment list
provided by customer service. If there are any discrepancies, notify the Customer
Service Center.
Step 2 Check for external damage.
Visually check all components and immediately report any shipping damage to
your customer service representative. Have the following information ready:
•Invoice number of shipper (see packing slip)
•Model and serial number of the damaged unit
•Description of damage
•Effect of damage on the installation
Keep a record of all of your hardware, configuration options, and network
settings.
Mounting the Chassis
The unit is designed for mounting in a rack. Use star-type lock washers on the
rack screws to ensure a good conductive connection between the chassis and the
rack. For information about installing the units in a customer cabinet, see the
instructions from the cabinet manufacturer.
Rack-Mounting the Chassis
You can install the Cisco ONS 15540 ESPx chassis in a standard 19-inch rack, a
21-inch rack, or a 23-inch rack. Table 2-1 lists the correct L bracket part number
required for each installation.
Table 2-1 L Bracket Part Numbers
Rack L Bracket Part Number
19-inch 700-15196-01
Chapter 2 Installing the Cisco ONS 15540 ESPx
Rack-Mounting the Chassis
2-4
Cisco ONS 15540 ESPx Hardware Installation Guide 78-16436-01
21-inch 700-15176-01
23-inch 700-18074-01
Table 2-1 L Bracket Part Numbers
Rack L Bracket Part Number
2-5
Cisco ONS 15540 ESPx Hardware Installation Guide
78-16436-01
Chapter 2 Installing the Cisco ONS 15540 ESPx Rack-Mounting the Chassis
To rack-mount the chassis, follow these steps:
Step 1 Place the L brackets on the sides of the chassis.
Step 2 Secure the L brackets to the chassis using the number 12-24 screws provided in
the rack-mount kit. (See Figure 2-1.) Use seven screws on each L bracket on the
sides of the chassis. Start with the first screw at the top of the chassis and use a
screw every 2 RU to equally space the screws out and safely secure the chassis in
the rack.
Figure 2-1 Attaching L Brackets
73368
Left mounting
bracket Right mounting
bracket
Chapter 2 Installing the Cisco ONS 15540 ESPx
Installing the Chassis
2-6
Cisco ONS 15540 ESPx Hardware Installation Guide 78-16436-01
Installing the Chassis
Warning
Only trained and qualified personnel should be allowed to install, replace, or
service this equipment.
To install the chassis in the rack, follow these steps:
Step 1 Grasp the bottom edge of the chassis with one hand near the front and the other
on the handles. With one person at each side of the chassis, use the handles on the
chassis to slowly lift the chassis in unison.
Step 2 Position the chassis in the rack.
Step 3 Align the mounting holes in the L bracket with the mounting holes in the
equipment rack. (See Figure 2-2.)
2-7
Cisco ONS 15540 ESPx Hardware Installation Guide
78-16436-01
Chapter 2 Installing the Cisco ONS 15540 ESPx Installing the Chassis
Figure 2-2 Installing the Chassis in the Rack
Step 4 Use the number 12-24 screws shipped with the chassis to mount the chassis in the
rack. (See Figure 2-2.) Use seven screws on each L bracket on the sides of the
chassis. Start with the first screw at the top of the chassis and use a screw every 2
RU to equally space the screws out and safely secure the chassis in the rack.
Step 5 Place the cable management tray over the fan assembly, ensuring that the tray is
just under the chassis slots.
Left mounting
rail
Mounting
screws (14)
Right mounting
rail
73369
Chapter 2 Installing the Cisco ONS 15540 ESPx
Installing the Chassis
2-8
Cisco ONS 15540 ESPx Hardware Installation Guide 78-16436-01
Step 6 Secure the cable management tray to the rack with four number 12-24 screws, two
on each side. To ensure correct placement of the tray, install the second of the two
screws in the sixth slot from the bottom of the chassis rack up on each side of the
cable management tray. (See Figure 2-3.)
Note Test the cable management tray placement before cabling up the system.
Step 7 Attach the top cable management guide to the chassis just above the slots using
the number 12-24 screws. Make sure the grounding holes are visible through the
top cable management guide.
2-9
Cisco ONS 15540 ESPx Hardware Installation Guide
78-16436-01
Chapter 2 Installing the Cisco ONS 15540 ESPx Installing the Chassis
Figure 2-3 Installing the Cable Management Tray
79721
Sixth mounting
hole above bottom
of chassis
mounting rails
Sixth mounting
hole above bottom
of chassis
mounting rails
Chapter 2 Installing the Cisco ONS 15540 ESPx
Installing the Drawers
2-10
Cisco ONS 15540 ESPx Hardware Installation Guide 78-16436-01
Installing the Drawers
The process for installing the cable storage and cross connect drawers is the same.
The order of placement beneath the chassis is important and should be installed
in the following order from top to bottom:
1. Cable storage drawer
2. Cross connect drawer
3. Cross connect drawer
4. Cable storage drawer
5. Cross connect drawer
6. Cross connect drawer
The first cable storage drawer can be used for direct connections and storage for
connections made using the first and second cross connect drawers. Each cable
storage drawer stores cables for two cross connect drawers.
The cross connect and cable storage drawers ship with the rack mount ears already
installed. To install the cross connect and cable storage drawers into the rack,
follow these steps:
Step 1 Hold the drawer with both hands and position the drawer in the rack beneath the
chassis. (See Figure 2-4.) All drawers following this first one can be stacked
directly underneath each other.
Autres manuels pour ONS 15540 ESPx
1
Table des matières
Autres manuels Cisco Unité de contrôle
Cisco
Cisco Catalyst 3110G Manuel
Cisco
Cisco 3600 Series Guide de démarrage rapide
Cisco
Cisco HPNA Manuel utilisateur
Cisco
Cisco Catalyst WS-X3001 Manuel de l'opérateur
Cisco
Cisco GS7000 Manuel de l'opérateur
Cisco
Cisco CSS 11500 Manuel de service
Cisco
Cisco MGX RPM-XF Manuel utilisateur
Cisco
Cisco ATUC-4DMT-ISDN Instructions d'utilisation et d'entretien
Cisco
Cisco 6015 Manuel d'utilisation et d'entretien
Cisco
Cisco WS-SVC-ASA-SM1-K7 Manuel d'installation et d'exploitation
Cisco
Cisco SM-X-1T3/E3 Manuel utilisateur
Cisco
Cisco Catalyst 5000 Series Manuel utilisateur
Cisco
Cisco GS7000 Mode d'emploi
Cisco
Cisco WS-G5484 Manuel utilisateur
Cisco
Cisco CGM-WPAN-OFDM-FCC Manuel utilisateur
Cisco
Cisco Beacon Point Module Manuel
Cisco
Cisco Firepower 4110 Manuel utilisateur
Cisco
Cisco TelePresence Touch10 Manuel utilisateur
Cisco
Cisco 3110 Manuel utilisateur
Cisco
Cisco MEM-CIP-64M Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
