Cabletron Systems WPIM-DI Instructions d'installation et d'entretien

WPIM-DI

Local Management Guide

9031709-01

WPIM-DI Local Management Guide i

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FORANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR

THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.



Printed in the United States of America

Order Number: 9031709-01 May 1998

Cabletron Systems

is a registered trademark and

CSX400

HSIM-W6

BRIM-W6

and

WPIM

are

trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

Only qualiﬁed personnel should perform installation

procedures.

Printed on Recycled Paper

Notice

ii WPIM-DI Local Management Guide

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

VCCI NOTICE

This is a Class A product based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,

radio disturbance may arise. When such trouble occurs, the user may be required to take corrective

actions.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in ﬁrmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME

BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND

THE LIMITATION OF WARRANTYAND DISCLAIMER OF LIABILITY. IFYOU DO NOT

AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED

PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

Notice

WPIM-DI Local Management Guide iii

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the

Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in

writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including

its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO

YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING

BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE

ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,

INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)

ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR

ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO

YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

Notice

iv WPIM-DI Local Management Guide

DECLARATION OF CONFORMITY

Application of Council Directive(s):

89/336/EEC

73/23/EEC

Manufacturer’s Name:

Cabletron Systems, Inc.

Manufacturer’s Address:

35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name:

Mr. J. Solari

European Representative Address:

Cabletron Systems Limited

Nexus House, Newbury Business

Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment:

Networking Equipment, for use

in a Commercial or Light

Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged

with this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

WPIM-DI Local Management Guide v

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 Using This Manual.......................................................................1-1

1.2 WPIM-DI Features.......................................................................1-2

1.3 Document Conventions...............................................................1-3

1.4 Related Manuals..........................................................................1-3

1.5 Getting Help.................................................................................1-4

CHAPTER 2 LOCAL MANAGEMENT

2.1 The WAN Physical Configuration Screen....................................2-2

2.1.1 WAN Physical Configuration Screen Fields....................2-2

2.1.2 WPIM-DI Line Configuration Fields ................................2-3

2.1.2.1 WPIM-DI Timeslot Configuration Table..........2-5

2.2 The WAN Interface Configuration Screen...................................2-9

2.2.1 WAN Interface Configuration Screen Fields...................2-9

2.3 WPIM-DI Configuration..............................................................2-11

2.3.1 WPIM-DI Physical Configuration ..................................2-12

2.3.2 WPIM-DI Interface Configuration..................................2-14

APPENDIX A WPIM-DI SPECIFICATIONS

A.1 WPIM-DI Specifications...............................................................A-1

A.2 WPIM-DI Interface Cables...........................................................A-2

A.3 Cable Assemblies and Pinouts....................................................A-2

APPENDIX B TYPICAL CONFIGURATIONS

B.1 Telco Timing................................................................................B-1

B.2 Tail Circuit Timing........................................................................B-1

B.3 Internal Timing.............................................................................B-2

APPENDIX C FCC PART 68 - USER’S INFORMATION

APPENDIX D WANTERMS AND ACRONYMS

Contents

vi WPIM-DI Local Management Guide

WPIM-DI Local Management Guide 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

WPIM-DI

Local Management

Guide

The WPIM-DI resides in and provides connectivity/functionality

to Cabletron Systems Wide Area Network (WAN) devices such as the

CSX400.

Before using this manual you must perform the following:

• Install the WPIM-DI in aWideArea Network host device. Refer to the

appropriate manual (i.e., the

CSX400 and CSX400-DC User’s Guide

)

for installation and troubleshooting procedures.

• Set up and access Local Management. Refer to the appropriate

standalone device or module User’s Guide for instructions on setting

up and accessing Local Management.

1.1 USINGTHIS MANUAL

Read through this guide completely to become familiar with the content

and to gain an understanding of the features and capabilities of the

WPIM-DI.You should have a general working knowledge of the

following data communications networks and their physical layer

components before using the WPIM-DI.

•WAN

• Ethernet and IEEE 802.3

The following brieﬂy summarizes each chapter of the WPIM-DI manual.

Chapter 1,

Introduction

, outlines the contents of this guide, describes

WPIM-DI features, provides a list of related manuals, and concludes with

instructions for obtaining help from Cabletron Systems Technical

Support.

Chapter 2,

Local Management

, describes how to use Local Management

to set up the WPIM-DI.

Chapter 1:

Introduction

1-2 WPIM-DI Local Management Guide

Appendix A,

WPIM-DI Specifications

, provides speciﬁcations for the

WPIM-DI and also gives Cabletron Systems part numbers and connector

information for WPIM-DI interface cables.

Appendix B,

Typical Configurations

, presents common conﬁgurations

for the WPIM-DI.

Appendix C,

FCC Part 68 - User’s Information

, explains the FCC rules

governing the WPIM-DI.

Appendix D,

WAN Terms and Acronyms

, provides a brief glossary of

the terms used in this book.

1.2 WPIM-DI FEATURES

The WPIM-DI extends the functionality of a Wide Area Network module

to allow remote connectivity using WAN services such as T-1, or

Fractional T-1.

The WPIM-DI provides a T-1 interface that includes a built-in Channel

Service Unit/Digital Service Unit (CSU/DSU) for direct connection to a

T-1 line. This WPIM supports both Full T-1 or Fractional T-1 using 56 or

64 Kbps timeslots.

The WPIM-DI also provides a Drop and Insert (DI) interface which

allows for a second WAN module (e.g., WPIM-T1) to utilize any

timeslots that are not used for host data. The WPIM-DI is capable of T1

multiframe alignment.

WAN Protocols

The module in which the WPIM-DI is installed supports the following

WAN protocols (refer to the Release Notes included with the host MIM or

standalone device for a list of current protocols):

• Point-to-Point Protocol (LCP) as deﬁned by RFC 1661

• Point-to-Point Protocol (BNCP) as deﬁned by RFC 1638

• Point-to-Point Protocol LAN Extender (PPP/LEX)

• Frame Relay as deﬁned by RFC 1490

MIB Support

Refer to the Release Notes included with the host MIM or standalone

device for a list of all MIBs supported by the WPIM-DI. For information

about how to extract and compile individual MIBs, contact Cabletron

Systems Technical Support (refer to Section 1.5,

Getting Help

Table des matières

Autres manuels Cabletron Systems Matériel réseau

Cabletron Systems

Cabletron Systems MMAC-M3FNB Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9A128-01 Manuel utilisateur

Cabletron Systems

Cabletron Systems SPECTRUM FRX6000 Manuel utilisateur

Cabletron Systems

Cabletron Systems EPIM-3PS Manuel utilisateur

Cabletron Systems

Cabletron Systems 1082 Manuel utilisateur

Cabletron Systems

Cabletron Systems SWPIM-E1 Manuel utilisateur

Cabletron Systems

Cabletron Systems BRIM-W6 Manuel utilisateur

Cabletron Systems

Cabletron Systems HSIM HSIM-A6DP- Manuel utilisateur

Cabletron Systems

Cabletron Systems 9A426-01 Manuel utilisateur

Cabletron Systems

Cabletron Systems W85 Manuel utilisateur

Cabletron Systems

Cabletron Systems Netlink FRX8000 Instructions de montage

Cabletron Systems

Cabletron Systems 3Com PortSwitch Hub Manuel utilisateur

Cabletron Systems

Cabletron Systems SSIM-T5-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems Expansion module DELHE-UA Manuel utilisateur

Cabletron Systems

Cabletron Systems SSIM-T8-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Instructions d'installation et d'utilisation

Cabletron Systems

Cabletron Systems KBU64 Rackmount Manuel utilisateur

Cabletron Systems

Cabletron Systems TRFMIM-22 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 6000 Manuel de programmation

Cabletron Systems

Cabletron Systems MMAC-5FNB Manuel utilisateur

Cabletron Systems

Cabletron Systems TPMIM-22 Manuel utilisateur

Cabletron Systems

Cabletron Systems SPECTRUM FRX6000 Manuel d'utilisation

Cabletron Systems

Cabletron Systems MMAC-Plus 9G536-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems DLM6C-AA Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur