BestScope BS-6000B Manuel utilisateur
Inverted Metallurgical
Microscope
Model Number
BS-6000B
User Manual
This manual is written for Inverted Metallurgical Microscope BS-6000B. Toensurethesafety,obtain optimum
performance and to familiarize yourself fully with the microscope, it is strongly recommended that you readthis
manual carefully before operating the microscope.
BestScope International Limited
1
Contents
User Notice.............................................................................................................................................2
I. Safety Precautions...............................................................................................................................2
II. Maintenance and Care....................................................................................................................... 2
III. Safety Symbols.................................................................................................................................3
1. Name of Components.........................................................................................................................4
2. Assembly Procedures......................................................................................................................... 5
3. Adjustment Set Diagram.................................................................................................................. 10
4. Adjustment Procedures.....................................................................................................................12
4-1 Microscope Base............................................................................................................................ 12
4-2 Mechanical Stage........................................................................................................................... 14
4-3 The Viewing Tube.......................................................................................................................... 15
5. Microscope Video and Photography................................................................................................ 16
5-1 Microscope Video.......................................................................................................................... 16
5-2 Microscope Photography............................................................................................................... 17
6．Technical Specification.................................................................................................................. 19
6-1 Main Technical Specification.........................................................................................................19
6-2 Objectives Specification................................................................................................................ 19
7．Trouble Shooting............................................................................................................................ 20
BestScope International Limited
2
User Notice
I. Safety Precautions
1. Be careful when moving the microscope, to avoid the lenses dropped or damaged.
2. Do keep the microscope out of direct sunlight, high temperature or humidity, dusty and easy shaking
environment. Make sure the stage is smooth, horizontal and firm enough.
3. When moving the instrument, grip two sides of the bottom of the microscope with your two hands.
4. When running, the lamp house and nearby parts will be very hot. Please ensure there is enough cooling
room for them.
5. Make sure the instrument is earthed, to avoid lighting strike.
6. For safety, be sure the main switch is in “O”(off) state and cut off the power supply before replacing the
bulb or the fuse. If you replace the bulb during use or right after use, allow the lamp bulb and the lamp
house to cool completely before touching.
(Designated bulb: 6V30W Halogen Lamp)
7. Check the input voltage: be sure the input voltage which is signed in the back of the microscope is
consistent with the power supply voltage, or it will bring a serious damage to the instrument.
II. Maintenance and Care
1. All the lenses have been adjusted properly; do not dismount them by yourself please.
2. The nosepiece and coarse and fine focusing parts are so delicate that it is forbidden to disassemble them
carelessly by yourself.
3. Keep the instrument clean ,and do not pollute the optical element when wiping away the dust on the
instrument.
4. The contamination on the prism, like fingerprints and oil smudges, could be gently wiped with a piece
of soft cloth or tissue paper, gauze which has been immersed in pure alcohol or ether. (Note that the
alcohol and ether are highly flammable, do keep them away from the fire or potential sources of
electrical sparks, and use them in a drafty room as possible as you can.)
5. Do not attempt to use organic solvents to clean the microscope components other than the glass
components. To clean them, use a lint-free, soft cloth slightly moistened with a diluted neutral
detergent.
6. When using, if the microscope is splashed by liquid, cut off the power at once, and wipe away the
splash.
7. Do not disassemble any parts of the microscope, as this will affect the function or reduce the
！Make sure that the input voltage is consistent with the power
supply voltage, or it will bring a serious damage to the instrument.
BestScope International Limited
3
performance of the microscope.
8. Place the instrument in a cool, dry position. After using the microscope, remember to cover it with dust
helmet. Do wait for the lamp house cooling completely before cover.
III. Safety Symbols
Symbol Explanation
Indicates that the surface becomes hot, and should not be touched with bare hands.
Before use, carefully read the user manual .Improper use could result in personal injury to
the user and/or damage to the equipment.
Indicates that the main switch is ON.
Indicates that the main switch is OFF.
BestScope International Limited
4
1. Name of Components
Fig.1
Trinocular
Viewing Head
Microscope Body
Stage Stage center plate
NosepieceObjectiveMetallurgical
Illumination System
eyepiece
BestScope International Limited
5
2. Assembly Procedures
Fig.3
Fig.2
2-1 Mounting the Objectives
(Fig.2 and Fig.3)
1. Turning the coarse focusing knob①as the figure shows
till the nosepiece gets to its lower limit.
★For ensuring the safety of the instrument during
transportation, the nosepiece is located in the lowest
position and the tension adjustment collar②is adjusted
to an appropriate tension while leaving the factory.
2. Screw the lowest magnification objective on to the
nosepiece from the nearside, then turn the
nosepiece clockwise, mount other objectives according the
magnification sequence of low to high.
◎Mounting objective in this way will make it easier to
change magnification.
◎The objective can also be mounted through the opening
on the stage.
★Clean the objective periodically, for the objectives used in
the inverted microscope are susceptible to dust.
★Do cover all the unused holes③on the nosepiece with
dust caps, to prevent the dirt and dust from getting inside.
★When operating, use the low magnification objective
(4X or 10X) to search and focus the specimen at first, then
replace with the higher magnification objective if
necessary.
★When replacing the objective, turn the nosepiece slowly
until you hear “clicked”, that means the objective enters
into the right position, center of the light path.
①②
③
BestScope International Limited
6
Fig.5
Fig.6
2-2 Mounting Auxiliary Stage and the
Mechanical Ruler
◎Auxiliary stage can be installed in either side of the
stage to enlarge the stage surface. But you can’t install
the mechanical ruler at the same side.
◎Generally, the mechanical ruler will be installed at
the right side for comfortable operation.
1. Installing the auxiliary stage
First, Screw the clamping bolts into to the auxiliary
stage, then into the main mechanical stage from below
on right or left side; Tighten it with a screwdriver until
the auxiliary stage is securely attached.
2. Installing the mechanical ruler
Please install the ruler in the same way as the
auxiliary stage.
2-3 Installing and Replacing the Bulb
(Fig.4-Fig.7)
Please use the specified halogen Lamp 6V30W.
1. Pull out the lamp house①asshowninfig.4
2. Holding the bulb ①with a piece of gauze or other
protection materials, insert the bulb pins straight and
fullyintothepinholes③on the lamp house. (Fig.5)
3. Bulb replacement during use or right after use. The
bulb, the lamp house and nearby parts will be very hot.
Please set the main switch to “O” (off), disconnect the
power cord, and make sure the bulb, the lamp house
and periphery are all cool. Then, you can do your
replacing.
Fig.4
BestScope International Limited
7
Fig.7
Fig.8
Fig.9
Please insert the lamp gently, or it will be damaged
by excessive extrusion.
Do not touch the halogen bulb with bare hands. It
will shorten the service life or cause it to burst. If you
leave fingerprints on the surface carelessly, clean it
withapieceofdrysoftcloth.
4. Align the socket①with pins③,and the bolts②with the
jacks④.then push the lamp-house all the way into
place.(Fig.6-7)
2-4 Installing the Stage Center Plate
（Fig.8）
1. When using the glass stage ①, there is no special
requirement, you just need to place it in the center of the
mechanical plain stage.
2. Install the stage center plate on to the stage opening.
2-5 Installing the Eyepiece (Fig.9)
1. Remove the cap of the eyepiece tube.
2. Insert the eyepiece into eyepiece tube until they are
against each other.
2-6 Mounting the video (photography)
adapter(Fig.10,11,12)
Insert the video (photography) adapter tube (Fig.10)
into the trinocular viewing head (Fig.11), and screw down
the bolt to fix it, as shown in Fig.12.
Fig.10 Fig.11
①
BestScope International Limited
8
Fig.13
Fig.12
Fig.14
①
②
①
2-7 Mounting Filters and Polarizer
(Fig.13)
Insert the filter①into the corresponding jack.
For polarization observation, insert the polarizer②
into the right jack, as shown in Fig.13.
★Standard filters include blue, yellow and green
filters.
2-8 Mounting Analyzer (Fig.14)
Insert the analyzer①into the jack under the
trinocular viewing head if necessary, as shown in
Fig.14
★Analyzer can be used alone or matched with the
polarizer.
BestScope International Limited
9
④
Fig 15
Fig.16
2-10 Replacing the Fuse (Fig.15-16)
Do remember to set the main switch①to the
state of “O” (OFF) and unplug the power cord
before replacing the fuse. Rotate the fuse⑦kits out
of the holder⑧with the “--”type screwdriver,
replacewithanewfuse,thenrotateitbacktothe
holder again.
★Fuse rating: 250V, 500mA.
2-9 Connecting the Power Cord
(Fig.15, Fig.16 and Fig.17)
★The cable and cords are vulnerable when
bent or twisted, never subject the power cord to
excessive force.
1. Set the main switch①to “O” (off) state before
connecting the power cord.
2. Insert the plugs into the power jack②of the
microscope safely.
3. Plug the power cord ③into the power supply
receptacle④. Make sure the connection is well.
4. Insert aviatic BNC connector plugs⑥into aviatic
BNC connector jack⑤.
★Do use the supplied power cord all the
time. If lost or damaged, select the same
standard cord, please.
★Connect the power cord correctly, to
ensure the instrument is grounded.
①
②
⑧
⑦
⑤
⑥
③
Fig.17
Table des matières
Autres manuels BestScope Microscope
BestScope
BestScope BS-3035 Series Manuel utilisateur
BestScope
BestScope BS-2005 Series Manuel utilisateur
BestScope
BestScope BS-6045 Manuel utilisateur
BestScope
BestScope BS-2030MH4B Manuel utilisateur
BestScope
BestScope BS-2080MH10 Manuel utilisateur
BestScope
BestScope BS-2052BDBD Manuel utilisateur
BestScope
BestScope BS-6004 Series Manuel utilisateur
BestScope
BestScope BS-2030MH4A Manuel utilisateur
BestScope
BestScope BS-5040B Manuel utilisateur
BestScope
BestScope BS-2092 Manuel utilisateur
BestScope
BestScope BS-2023B Manuel utilisateur
BestScope
BestScope BS-2081 Manuel utilisateur
BestScope
BestScope BS-2020B Manuel utilisateur
BestScope
BestScope BS-2081L Manuel utilisateur
BestScope
BestScope BS-3001 Series Manuel utilisateur
BestScope
BestScope BS-6012 Series Manuel utilisateur
BestScope
BestScope BS-2081F Manuel utilisateur
BestScope
BestScope BS-2076 Series Manuel utilisateur
BestScope
BestScope BS-2094 Series Manuel utilisateur
BestScope
BestScope BS-6023 Series Manuel utilisateur
Manuels Microscope populaires d'autres marques
VWR
VWR VisiScope 384 Series Manuel utilisateur
Nikon
Nikon ECLIPSE E200 POL Manuel utilisateur
Leica
Leica DI C800 Manuel
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manuel utilisateur
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manuel utilisateur
Olympus
Olympus SZ61 Manuel utilisateur