Belden Hirschmann MAMMUTHUS MTS2600 Manuel utilisateur

Installing MAMMUTHUS SWITCH

Published on

1/2020

Technical support

://

hirschmann

it.support.belden.com

User manual

Installation

MAMMUTHUS ACCESS LAYER & DISTRIBUTION

LAYER SWITCH – MTS2600/2700/2800

MAMMUTHUS POWER MODULE –

MTM2700-PSU500/PSU120

MAMMUTHUS MEDIA MODULE – MTM2700-2X

MAMMUTHUS SWITCH

Even if not specifically stated, the copyrighted trademark names in this manual shall not be deemed free of

charge in the sense of the trademark and trade name protection act and thus freely available to anyone.

shall be prohibited from being reproduced, copied, translated or converted into any electronic media or

machine-scannable form, except in the case that you make a copy of the software for your own use.

The performance characteristics described herein shall be binding only upon the express consent of the

parties at the time of signing the contract. This paper is produced by Belden within its capacity. Belden

reserves the right to change the contents of this manual without prior notice. Belden does not guarantee the

correctness or accuracy of the information in this manual.

Belden shall not be liable for damages caused by the use of network components or related operating

software. And the conditions of use specified in the license contract are referred to in this manual.

You may access the latest version of this manual at the product website of Hirschmann IT:

https://hirschmann-it.support.belden.com

Installing MAMMUTHUS SWITCH

Published on 01

01/2020

Contents

Safety guidelines 6

About the manual 13

Legend 14

1 Description 15

1.1 General equipment description 15

1.2 Equipment name and product code 19

1.2.1 Basic device 19

1.2.2 Power module 20

1.2.3 Media module 20

1.3 Equipment view 21

1.3.1 MTS2624-4X-B 21

1.3.2 MTS2724-4X-FP-S 21

1.3.3 MTS2724-6X-MP-E 22

1.3.4 MTS2748-6X-MP-E 23

1.3.5 MTS2824-4X-S 24

1.3.6 MTS2824-6X-E 25

1.3.7 MTS2824F-4X-S 26

1.3.8 MTS2832TF-4X-E 27

1.3.9 MTS2848-6X-E 28

1.3.10 MTS2848-6X-S 29

1.3.11 Power module 30

1.3.12 Media module 32

1.4 Power supply 33

1.5 Ethernet port 34

1.5.1 100/1000 Mbit/s F/O port 34

1.5.2 10 Gbit/s F/O port 34

1.5.3 10/100/1000 Mbit/s twisted pair port 34

4 Installing MAMMUTHUS SWITCH

Published on 01

01/2020

1.5.4 PoE(+) support 34

1.5.5 Out-of-band management port 35

1.6 Display unit 36

1.6.1 Equipment status 36

1.6.2 Port Status 37

1.7 Management interface 38

1.7.1 DC0 interface (external management) 38

1.7.2 USB interface 38

2 Installation 39

2.1 Unpack the box for inspection 39

2.2 Install power module (optional) 39

2.2.1 Install power module 39

2.3 Install equipment and ground 40

2.4 Install SFP transceiver (optional) 41

2.5 Operate equipment 42

2.6 Connect data cable 42

2.7 Fill in the Device Label 42

3 Make basic settings 43

4 Monitor ambient air temperature 44

5 Maintenance and repair 45

6 Remove 46

6.1 Remove power module 46

6.2 Remove media module 46

6.3 Remove SFP transceiver 47

6.4 Remove device 48

7 Technical data 49

7.1 General technical data 49

7.2 Dimension drawing 51

7.3 EMC and immunity 63

Installing MAMMUTHUS SWITCH

Published on 01

01/2020

7.4 Network range 66

7.5 Power consumption / power output 67

8 Delivery item, order number and accessories 68

9 Basic technical standards 69

A More support 71

6 Installing MAMMUTHUS SWITCH

Published on 01

01/2020

Safety guidelines

Warning

Uncontrolled machine action

To avoid uncontrolled machine action due to data loss, configure all data

transfer devices separately.

Before start

ing any machine controlled by data transfer, be sure to complete

the configuration of all data transfer devices.

Failure to comply with these guidelines may result in death, serious

injury or equipment damage.

 General safety guidelines

Hot-line work is required for the equipment. Improper use of the equipment

may result in personal injury or great destruction of property. The proper

and safe operation of the equipment depends on proper handling during

transportation, reasonable storage and installation, as well as careful

establishment and strict adherence to the operation and maintenance

procedures.

 Please read this manual as well as safety guidelines and warnings

before connecting any cable.

 Only operate the equipment without any damaged components.

 Make sure there is no component to be repaired in the equipment. In

case of any damage or failure to the equipment, switch off the power

and return the equipment to Belden for inspection.

 Qualification requirements for operators

 Only qualified personnel are allowed to operate the equipment.

Qualified personnel have the following characteristics:

 They shall receive appropriate training. Training and required practical

knowledge and experience are prerequisites to be qualified for product

operation. Only when these prerequisites are met can operators

perform grounding and labeling operations on circuits, equipment and

systems in accordance with current safety technical standards.

 Qualified personnel shall be aware that there is danger in their work.

 Qualified personnel shall know well how to deal with these hazards to

reduce risks posed to themselves and others.

 Qualified personnel shall receive training on a regular basis.

Installing MAMMUTHUS SWITCH

Published on 01

01/2020

 Correct use

Use the equipment only for the purposes specified in the catalog and

technical instructions. Only external devices and components

recommended and permitted by the manufacturer can be used to operate

the equipment.

The correct and safe operation of this product depends on the correct

operation, storage, assembly and installation during transport, as well as

careful operation and maintenance procedures.

 National and international safety regulations

Carry out validation to ensure that electrical installations comply with

applicable local or national safety regulations.

 Wire connection requirements

Always make sure that all requirements listed are met before connecting

the wires.

The requirements below shall apply without limitation:

 The wires are voltage free.

 The cables used meet the temperature range required for a particular purpose.



First, connect the ground screw on the back of the equipment to the protective conductor before setting

up other connections. When to remove connections, the protective conductor shall be the last to be

removed.

 Do not power up the equipment during installation.



Requirements for North America:

Use 60 / 75 ° C (140 / 167 ° F) or 75 ° C (167 ° F) copper (Cu) wires only.

Table 1: Wire connection requirements

 Power voltage connection requirements

Device Model

The requirements below shall apply without limitation:

All

model

Meet

all

of the following requirements

 The supply voltage shall be consistent with the specified value on the equipment

nameplate.

 The power supply shall conform to overvoltage category I or II.

 The power supply shall be equipped with an easy-to-operate disconnector (such as a

switch or plug).



The disconnector shall be clearly marked, so that in an emergency, the operator

knows at a glance the correspondence between the disconnector and the power

cable.



When to connect a power supply voltage with a protective conductor: first connect the

protective conductor, and then the power supply voltage. If the equipment contains

such a second power supply voltage connection module: first connect the protective

conductor, and then the power supply voltage.

 Supply with DC voltage:

 Power cord diameter at the power supply voltage input shall be at least 1mm² (North

America: AWG16). Supply with AC voltage:

8 Installing MAMMUTHUS SWITCH

Published on 01

01/2020

 Power cord diameter at the power supply voltage input shall be at least 0.75 mm²

(North America: AWG18).

 The cross section of the grounding conductor shall be the same as or larger than that

of the power cord.

 Power cables suitable for voltage, current and physical loads shall be used.

 The external fuse shall be installed in the conductor at the non-spot position.

Table 2: Power voltage connection requirements

Installing MAMMUTHUS SWITCH

Published on 01

01/2020

Special conditions for safe use

 Install the basic equipment and modules in a suitable enclosure based

on specific environmental conditions to provide at least IP54 protection

according to the requirements of EN 60529.

 Take measures to prevent instantaneous interference from exceeding

140% of the rated voltage at the voltage input.

 Shield grounding

The shield grounding module of the twisted-pair cable shall be connected

to the front panel as a conductor.

When connecting a cable segment with a conductive shield braid, pay

attention to the possible short circuit.

 ESD guide

These modules are equipped with electrostatic sensitive components.

If the connection is touched, these sensitive components may be damaged

or their service life shortened by electric field or charge balance effects.

You may find information about electrostatic hazard components in DIN

EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).

10 Installing MAMMUTHUS SWITCH

Published on 01

01/2020

 Equipment enclosure

Only technicians authorized by the manufacturer are allowed to open the

enclosure.

 Keep vents open to ensure good air circulation.

 Ensure a minimum of 3.94 inches (10 cm) of space in front of the

enclosure vent.

 Do not touch the enclosure during operation or shortly after shutting

down the equipment. Hot surfaces may cause injury.

 Install the equipment horizontally in the cabinet or vertically on a flat

surface.

Do not place the equipment on the desktop for operation. See Page 40

for details of “Install equipment and ground”.

 Operate the equipment at the maximum ambient air temperature and in

stacking: when to install the equipment, make sure that there is at least

one available rack space (approx. 5 cm) above the equipment to allow

heat to escape through the enclosure of the equipment.

 If you operate the equipment in 19” switch cabinet: install the slide /

rails to support the weight of the equipment.

 Installation site requirements

The equipment can only be operated at the specified ambient temperature

- the ambient air temperature at a distance of 2 inches (5 cm) from the

equipment - with relative humidity.

 When selecting the installation position, be sure to comply with the

climate thresholds set forth in the technical data.

 Please use the equipment in the environment where the maximum

pollution level conforms to the technical data.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Belden Changer

Belden

Belden Hirschmann RS20 U Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Belden

Belden HIRSCHMANN EESX Series Guide de configuration rapide

Belden

Belden HIRSCHMANN SPIDER II Manuel utilisateur

Belden

Belden HIRSCHMANN Octopus II Manuel utilisateur

Belden

Belden HIRSCHMANN RSPE 30 Manuel utilisateur

Belden

Belden Hirschmann MACH4002 Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manuel utilisateur

Belden

Belden HIRSCHMANN OCTOPUS OS3 Manuel utilisateur

Belden

Belden Hirschmann HiOS-2S Manuel utilisateur

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Manuel utilisateur

Belden

Belden HIRSCHMANN PTN-CSM310-A Manuel utilisateur

Belden

Belden Hirschmann MACH102 Series Manuel utilisateur

Belden

Belden HIRSCHMANN MSP30 Manuel utilisateur

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manuel utilisateur

Belden

Belden Hirschmann MACH1000 Series Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden Hirschmann Rail Switch Power Lite Manuel utilisateur

Belden

Belden Hirschmann SPIDER 8TX EEC Manuel

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur