Belden Hirschmann RED25 Series Manuel utilisateur

Installation RED25

Release

02/2015

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Redundancy Switch

RED25

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation RED25 040 068-001-01-0215 -20.02.2015

Installation RED25

Release

02/2015 3

Contents

Safety instructions 5

About this manual 11

Key 11

1 Description 12

1.1 General description 12

1.2 Device name and product code 13

1.3 Device views 16

1.4 Power supply 17

1.5 Ethernet ports 17

1.5.1 10/100 Mbit/s twisted pair port 17

1.5.2 100 Mbit/s F/O port (optional) 18

1.6 Display elements 18

1.6.1 Device state 18

1.6.2 Port state 19

1.7 Management interfaces 19

1.7.1 V.24 interface (external management) 19

1.7.2 USB interface 20

1.8 Signal contact 21

2 Installation 22

2.1 Checking the package contents 22

2.2 Installing and grounding the device 22

2.2.1 Installing the device onto the DIN rail 23

2.2.2 Grounding the device 23

2.3 Installing an SFP transceiver (optional) 23

2.4 Connecting the power supply and signal lines 24

2.5 Operating the device 26

2.6 Connecting data cables 26

2.7 Filling out the inscription label 26

3 Making basic settings 27

4 Monitoring the ambient air temperature 28

4Installation RED25

Release

02/2015

5 Maintenance and service 29

6Disassembly 30

6.1 Removing the device 30

6.2 Removing an SFP transceiver (optional) 31

7 Technical data 32

A Further Support 39

Installation RED25

Release

02/2015 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful opera-

tion and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Intended usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 32.

Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RED25

Release

02/2015

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Requirements for connecting electrical conductors

Before connecting the electrical conductors, always verify that all of

the requirements listed are fulfilled:

All of the following requirements are fulfilled:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Relevant for North America:

Use 60/75 or 75 °C copper (Cu) wire only.

Table 1: General requirements for connecting electrical conductors

All of the following requirements are fulfilled:

The voltage connected meets the requirements for a safety extra-low voltage (SELV) as per

IEC/EN 60950-1.

The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 32.

Table 2: Requirements for connecting the signal contact

Relevance Requirements

Absolutely relevant All of the following requirements are fulfilled:

The supply voltage corresponds to the voltage specified on the

type plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly iden-

tified. So in the case of an emergency, it is clear which discon-

necting device belongs to which power supply cable.

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the supply voltage input.

The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

Table 3: Requirements for connecting the supply voltage

Installation RED25

Release

02/2015 7

Relevant when the

device is supplied via 1

voltage input

The following requirements are alternatively fulfilled:

Alternative 1 The voltage supply meets the requirements for a

limited power source (LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The voltage supply meets the requirements as

per NEC Class 2

Alternative 3 All of the following requirements are fulfilled:

The voltage supply meets the requirements

for a safety extra-low voltage (SELV) as per

IEC/EN 60950-1.

Supply with DC voltage:

A fuse suitable for DC voltage is located in

the plus conductor of the power supply.

The minus conductor is on ground potential.

Otherwise, a fuse is also located in the minus

conductor.

Regarding the properties of this fuse:

See “General technical data” on page 32.

Supply with AC voltage:

A fuse is located in the outer conductor of the

power supply.

The neutral conductor is on ground potential.

Otherwise, a fuse is also located in the

neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 32.

Relevance Requirements

Table 3: Requirements for connecting the supply voltage

8Installation RED25

Release

02/2015

Supply voltage

The supply voltage is only connected with the chassis via protective

elements.

Installation site requirements

Verify that there is at least 4 in (10 cm) of space above and below the

device.

Verify that there is at least 0.8 in (2 cm) of space on the right and left

sides of the device.

Install the device in a fire protected enclosure according to

EN 60950-1.

Relevant when the

device is supplied via 2

voltage inputs

The following requirements are alternatively fulfilled:

Alternative 1 The total voltage supply meets the requirements

for a limited power source (LPS) as per EN

60950-1.

Alternative 2 Relevant for North America:

The total voltage supply meets the requirements

as per NEC Class 2.

Alternative 3 All of the following requirements are fulfilled:

The voltage supply meets the requirements

for a safety extra-low voltage (SELV) as per

IEC/EN 60950-1.

Supply with DC voltage:

A fuse suitable for DC voltage is located at

both voltage inputs in the plus conductor of

the power supply.

The minus conductor is on ground potential

at both voltage inputs. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 32.

Supply with AC voltage:

A fuse is located at both voltage inputs in the

outer conductor of the power supply.

The neutral conductor is on ground potential

at both voltage inputs. Otherwise, a fuse is

also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 32.

Relevance Requirements

Table 3: Requirements for connecting the supply voltage

Installation RED25

Release

02/2015 9

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

Install the device in the vertical position.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2004/108/EC (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic compati-

bility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

You find more information on technical and industry standards here:

“Technical data” on page 32

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take appro-

priate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

10 Installation RED25

Release

02/2015

LED or laser components

LED or LASER components according to IEC 60825-1 (2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the require-

ments of a class A digital device in line with part 15 of the FCC regula-

tions.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this oper-

ating manual, it can cause radio transmission interference. The use of this

device in a residential area can also cause interference, and in this case

the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Belden Changer

Belden

Belden Hirschmann MICE MS20 Manuel utilisateur

Belden

Belden MAMMUTHUS MTM2800-PSU120 Manuel utilisateur

Belden

Belden Hirschmann MICE MS20 Manuel utilisateur

Belden

Belden Hirschmann MACH1000 Series Manuel utilisateur

Belden

Belden Hirschmann OCTOPUS 8TX PoE-EEC Manuel utilisateur

Belden

Belden Hirschmann SPIDER 8TX EEC Manuel

Belden

Belden HIRSCHMANN HiOS-2A Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden Grass Valley K-Frame Comment utiliser

Belden

Belden HIRSCHMANN GRS105 Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Belden

Belden HIRSCHMANN MACH4002-48+4G Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden Hirschmann RS20 U Series Manuel utilisateur

Belden

Belden HIRSCHMANN PTN-CSM310-A Manuel utilisateur

Belden

Belden Hirschmann MACH102 Series Manuel utilisateur

Belden

Belden Hirschmann SPIDER 8TX EEC Manuel utilisateur

Belden

Belden HIRSCHMANN SPIDER II Manuel utilisateur

Belden

Belden grass valley MASTERPIECE 12G-SDI Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden Hirschmann MACH104 Series Guide de l'utilisateur

Belden

Belden Hirschmann DRAGON MACH Series Manuel utilisateur

Belden

Belden Hirschmann Rail Switch Power Lite Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur