Belden Hirschmann RS20 Series Manuel utilisateur

Installation RS20/22/30/32/40

Release

02/2015

Technical Support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch

RS20/RS22/RS30/RS32/RS40 Family

RS30-0802...

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS30-1602...

RS20

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0800...RS20-2400... RS20-0400...

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0900...

RS40

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS40-0009... RS32-0802... RPS90/48V HV

RPS90/48V HV

U: 110 / 230 VAC

U: 60 / 250 VDC

-/N

+/L

+48V / 1,9A

48-54V

RS32

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

FAULT

+48V(P1) 0V 0V +48V(P2)

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. The end user license on the provided CD/DVD is effective for devices with

embedded software.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This publication was created by Hirschmann Automation and

Control GmbH to the best of its knowledge. Hirschmann reserves the right to change the content

of this publication at any time without notice. Hirschmann does not give any warranty or

assurance with respect to the correctness or accuracy of the details in this publication.

Hirschmann accepts no liability for damage in any way related to the use of the network

components or their operating system software. In addition, we refer to the conditions of use

specified in the license contract.

You will the latest version of this manual on the internet at Hirschmann product pages

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

RS20/22/30/32/40 039 692-003-04-0215 –15.04.2015

Installation RS20/22/30/32/40

Release

02/2015 3

Content

Safety Information 5

About this manual 16

Key 16

1 Description 17

1.1 Description of the device variants 18

1.1.1 Combination options of the device variants

RS20/RS30/RS22/RS32 19

1.1.2 Combination options for the RS40 device variants 22

1.1.3 Number of ports and media for RS20-... 24

1.1.4 Number of ports and media for RS30-... 27

1.1.5 Number of ports and media for RS40-... 30

1.2 Device variants with PoE (optional) 31

1.2.1 Number of ports and media for devices with PoE 31

1.2.2 PoE power units 33

1.3 Ethernet ports 33

1.3.1 10/100/1000 Mbit/s twisted pair port 33

1.3.2 10/100 Mbit/s twisted pair port 34

1.3.3 10/100 Mbit/s twisted-pair connection PoE

(RS22-.../RS32-...) 34

1.3.4 1000-Mbit/s F/O port 35

1.3.5 100 Mbit/s F/O port 36

1.3.6 Gigabit combo port 36

1.4 Display elements 37

1.5 Management interfaces 38

1.5.1 USB interface 38

1.5.2 V.24 interface (external management) 39

2 Installation 40

2.1 Checking the package contents 40

2.2 Installing and grounding the device 40

2.2.1 Snapping a unit onto the DIN rail 41

2.2.2 DIN rail mounting on ships (RS30-0802...) 42

2.2.3 Mounting on a vertical flat surface 43

2.2.4 Grounding 43

2.3 Installing an SFP transceiver (optional) 44

2.4 Adjust DIP switch settings 44

4Installation RS20/22/30/32/40

Release

02/2015

2.5 Wiring the terminal blocks 45

2.5.1 RS20/RS30/RS40 supply voltage and Signal contact 45

2.5.2 RS22/RS32: Supply voltage and signal contact 46

2.6 Mounting a terminal block 50

2.7 Connecting the ferrite 50

2.8 Operating the device 50

2.9 Connecting data cables 51

2.10 Insert data in label area 51

3 Making basic settings 52

4 Monitoring the ambient air temperature 53

5 Maintenance and service 54

6Disassembly 55

6.1 Removing the device 55

6.2 Removing an SFP transceiver (optional) 56

7 Technical Data 57

A Further support 71

Installation RS20/22/30/32/40

Release

02/2015 5

Safety Information

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Intended usage

Use the device only for the application cases described in the Hirschmann

product information, including this manual.

Operate the device only according to the technical specifications.

See “Technical Data” on page 57.

Installation site requirements

Install the device in a fire enclosure according to EN 60950-1.

If installed in a living area or office environment, the device must be

operated only in switch cabinets with fire protection characteristics

according to EN 60950-1.

Only when using the PoE power supply unit RPS90/48V HV:

Install the device at ambient temperatures greater than 113 °F (45 °C)

in “restricted access locations” based on EN 60950-1 exclusively.

Install this device only in a switch cabinet or in a restricted access

location, to which maintenance staff have exclusive access.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RS20/22/30/32/40

Release

02/2015

Device casing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 57.

Install the device in the vertical position.

At ambient temperatures > 60 °C:

The surfaces of the device casing may become hot. Avoid touching the

device while it is operating.

Qualification requirements for personnel

Allow qualified personnel exclusively to perform any work on the

device.

Qualified personnel are characterized by the following points:

The qualified personnel has received an appropriate training. Proper

training as well as a practical knowledge and experience constitute the

qualification. This qualification is the requirement to connect, to ground

and to label power circuits, devices, and systems in accordance with

current safety engineering standards.

The qualified personnel are aware of the hazards associated with their

tasks.

The qualified personnel know proper measures against such hazards

to minimize the risk for themselves and others.

The qualified personnel participate in regular training.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

Use a wire diameter of at least 1.0 mm² for the ground conductor.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Shielding ground

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation RS20/22/30/32/40

Release

02/2015 7

Supply voltage

The supply voltage is electrically isolated from the housing.

The devices are designed for operation with safety extra-low voltage.

Connect only safety extra-low voltage circuits with voltage restrictions

in line with IEC/EN 60950-1 to the supply voltage connections and

signal contacts.

Connect only a supply voltage that corresponds to the type plate of

your device.

Observe the maximum values for contact load of the signal contact.

Applies to North America:

The device must only be connected to a Class 2 supply voltage that

meets the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Applies to North America: For use with Class 2 circuits only.

Use only copper wire (Cu) 60/75 °C or 75 °C.

Applies to North America:

For modules certified for hazardous locations: make sure that

peripheral devices are suitable for the application environment. The

wiring for the voltage supply and for the inputs and outputs (I/O) must

adhere to the wiring regulations for Class I, Division 2 [article 501(b) of

the National Electrical Code (USA), NFPA 70] and to the applicable

statutory regulations.

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Enable the supply voltage for the device only when the following

requirements are fulfilled:

the housing is closed

the terminal blocks are wired correctly

the terminal blocks for the power supply are connected

Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

supply voltage and return the device to the plant for inspection.

8Installation RS20/22/30/32/40

Release

02/2015

Supply voltage for PoE power supply units (optional)

Connect the protective conductor with the ground screw before you set

up the other connections. When removing the cables, remove the

protective conductor last.

Make sure that the cross-section of the protective conductor cable is

the same size as or bigger than the cross-section of the voltage supply

cables.

Only use connection cables that are permitted for the specified

temperature range.

Connect only a supply voltage that corresponds to the type plate of

your device.

PoE power supply unit RPS90/48V LV:18 V DC to 60 V DC

PoE power supply unit RPS90/48V HV:48 V DC to 320 V DC or 90

V AC to 265 V AC

Install a suitable input fuse in the following cases:

The neutral conductor or the negative terminal of the supply voltage

is ungrounded.

For the supply voltage, you provide a DC voltage greater than

125 V DC.

See “General technical data” on page 57.

With AC power supply, use a cable cross-section of at least 0.75 mm²

(for North America AWG 18) for the current conductor at the voltage

input.

With DC power supply, use a cable cross-section of at least 1.0 mm²

(for North America AWG 16) for the current conductor at the voltage

input.

Installation RS20/22/30/32/40

Release

02/2015 9

ATEX directive 94/9/EC – specific regulations for safe

operation

Relevant for RS20/22/30/32/40 devices when operating in explosive gas

atmospheres according to ATEX Directive 94/9 EC, the following applies:

List of standards:

EN 60079-0:2009

EN 60079-15:2010

Certificate No.: DEKRA 11ATEX0139 X or KEMA 09ATEX0067 X.

Make sure that the device has the following label:

II 3G Ex nA IIC T4 Gc DEKRA 11ATEX0139 X

for RS20/22/30/32 types.

II 3G Ex nA IIC T3 ... T4 Gc KEMA 09ATEX0067 X

for RS40 types.

Environmental class and temperature code for types RS20 and RS30:

T4: 0 °C ≤Ta ≤+60 °C for "S" types

(Item 14 in the schematic legend) or

T4: −40 °C ≤Ta ≤+70 °C for "T" or "E" types

(Item 14 in the schematic legend).

Environmental class and temperature code for types RS22 and RS32:

T4: −40 °C ≤Ta ≤+70 °C for "T" or "E" types

(Item 14 in the schematic legend) or

T4: 0 °C ≤Ta ≤+50 °C for "S" types

(Item 14 in the schematic legend) or

Environmental class and temperature code for RS40 types:

T3: −40 °C ≤Ta ≤+70 °C for "T" or "E" types

(Item 14 in the schematic legend) or.

T4: −40 °C ≤Ta ≤+60 °C for “T” or “E” types

(item 14 of nomenclature breakdown).

T4: 0 °C ≤Ta ≤+60 °C for “S” types

(item 14 of nomenclature breakdown).

The modules shall be installed in a suitable enclosure in accordance

with EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

When the temperature under rated conditions exceeds 70 °C at the

cable or conduit entry point, or 80 °C at the branching point of the

conductors, the temperature specification of the selected cable and

cable entries shall be in compliance with the actual measured

temperature values.

10 Installation RS20/22/30/32/40

Release

02/2015

Make provisions to prevent the voltage of the rated voltage

connections from exceeding the 119 V threshold due to transient

disturbances.

Connectors shall be connected or disconnected exclusively in dead-

voltage state.

DIP switches shall be switched exclusively in dead-voltage state.

The USB port shall remain disconnected.

Relevant for use in explosion hazard areas (Hazardous

Locations, Class I, Division 2):

Applies to North America for devices certified for hazardous locations:

The grid, input and output wiring (I/O) must comply with the requirements

of wiring procedures Class I, Division 2, [Article 501-4(b) of the National

Electrical Code, NFPA 70], and must comply with legal requirements.

ONLY SUITABLE FOR USE IN HAZARDOUS LOCATIONS OF CLASS

I, DIVISION 2, GROUPS A, B, C, AND D, OR IN NON-HAZARDOUS

LOCATIONS.

CAUTION: RISK OF EXPLOSION - REPLACEMENT OF ANY PART

CAN IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.

CAUTION: RISK OF EXPLOSION - ONLY DISCONNECT DEVICES

WHEN THE SYSTEM HAS BEEN DE-ENERGIZED OR IS LOCATED IN

AN AREA WITHOUT FLAMMABLE CONCENTRATIONS.

The USB connector is for temporary connection only. Do not use, connect

or disconnect unless the area is known to be non-hazardous. Connection

or disconnection in an explosive atmosphere could result in an explosion.

Peripheral equipment must be suitable for the location in which it is used.

Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.

Avertissement - Risque d'explosion - Ne pas débrancher tant que le

circuit est sous tension à moins que l'emplacement soit connu pour ne

contenir aucune concentration de gaz inflammable.

Avertissement - Risque d'explosion - La substitution de tout composant

peut rendre ce matériel incompatible pour une utilisation en classe I,

division 2.

Autres manuels pour Hirschmann RS20 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Belden Changer

Belden

Belden ThinkLogical TLX12 Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Belden

Belden Grass Valley Kayenne Supplément

Belden

Belden Grass Valley K-Frame Comment utiliser

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manuel utilisateur

Belden

Belden Thinklogical TLX48 Manuel utilisateur

Belden

Belden HIRSCHMANN MACH 100 Series Manuel utilisateur

Belden

Belden Hirschmann MICE MS20 Manuel utilisateur

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Manuel utilisateur

Belden

Belden Hirschmann DRAGON MACH Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden grass valley SIRIUS 800 Series Guide de l'utilisateur

Belden

Belden Hirschmann MACH102 Series Manuel utilisateur

Belden

Belden HIRSCHMANN OCTOPUS OS3 Manuel utilisateur

Belden

Belden Hirschmann SPIDER 8TX EEC Manuel

Belden

Belden Hirschmann MAMMUTHUS MTS2600 Manuel utilisateur

Belden

Belden lumberg automation 0960 IOL 3816-001 Manuel utilisateur

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manuel utilisateur

Belden

Belden Hirschmann GREYHOUND GRS1042 Manuel utilisateur

Belden

Belden HIRSCHMANN MACH 4000 Series Manuel utilisateur

Belden

Belden HIRSCHMANN RSPE 30 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur