Belden Hirschmann MICE MS20 Manuel utilisateur

Installation MS20/MS30

Release

09/2019

Technical Support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial ETHERNET Switch MICE

MS20/MS30

MICE MS20 MICE MS30

17.9.19 Installation MS20/MS30

Release

09/2019

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation MS20/MS30

Release

09/2019 3

Contents

Safety instructions 5

About this Manual 19

Legend 20

1 Description 21

1.1 General device description 21

1.2 Device name and product code 23

1.3 Description of the device variants 24

1.3.1 Number of ports and connections 25

1.3.2 Media modules 29

1.3.3 Digital I/O Module MM24 34

1.3.4 MB20 extender module 34

1.3.5 SFP Transceiver 34

1.4 Ethernet ports 35

1.4.1 10/100/1000 Mbit/s twisted pair port 35

1.4.2 10/100 Mbit/s twisted pair port 36

1.4.3 10/100 Mbit/s PoE port 36

1.4.4 1000 Mbit/s F/O port 36

1.4.5 100 Mbit/s F/O port 37

1.4.6 Pin assignments 37

1.5 AUI port 38

1.6 Display elements 39

1.6.1 Device status 40

1.6.2 Display status 41

1.6.3 Port status 42

2 Installation 43

2.1 Checking the package contents 43

2.2 Installing media modules 44

2.3 Filling out and attaching labels 44

2.4 Installing an SFP transceiver (optional) 46

2.5 Adjusting the DIP switch settings on the basic module (4-pin

DIP switch) 46

2.6 Adjusting the DIP switch settings on the MS20/MS30-...E...

basic module (3-pin DIP switch) 48

4Installation MS20/MS30

Release

09/2019

2.7 Adjusting the DIP switch settings on the

MM20-A8A89999SAHH media module 49

2.8 Connecting the MM22-T1T1T1T1 PoE media module 49

2.9 Terminal block for supply voltage and signal contact 51

2.9.1 Supply voltage 51

2.9.2 Signal contacts 51

2.10 Connecting the terminal blocks, start-up procedure 52

2.10.1 Terminal blocks on MS20/MS30-...A... and MS20/

MS30-...C... 52

2.10.2 Terminal block on MS20/MS30-...E... 53

2.10.3 Operating the device 53

2.11 Installing and grounding the device 54

2.11.1 Installing the device onto the DIN rail 54

2.11.2 Grounding the device 55

2.12 Connecting data cables 55

2.12.1 Twisted Pair ports 55

2.12.2 Optical fiber ports 55

2.13 Assembly of the MB20 extender module 56

2.14 Defining the meaning of the display LEDs 56

3 Making basic settings 57

4 Maintenance and service 59

5Disassembly 60

5.1 Removing the device 60

5.2 Removing an SFP transceiver (optional) 61

6 Technical data 62

A Further support 81

Installation MS20/MS30

Release

09/2019 5

Safety instructions

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

Supply voltage

The devices are designed for operation with safety extra-low voltage.

Connect only SELV circuits with voltage restrictions in line with IEC/EN

60950-1 to the supply voltage connections and signal contacts.

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

Relevant for North America:

The device may only be connected to a Class 2 supply voltage that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

Use in Hazardous Locations

Relevant for North America for modules certified for Hazardous

Locations:

This equipment is suitable for use in Class 1, Division 2, Groups A, B,

C and D or Non-Hazardous (unclassified) locations only.

Make sure that peripheral devices are suitable for the application

environment. The wiring for the voltage supply and for the inputs and

outputs (I/O) must adhere to the wiring regulations for Class 1,

Division 2 [article 501(b) of the National Electrical Code (USA),

NFPA 70] and to the applicable statutory regulations.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation MS20/MS30

Release

09/2019

Note: Observe the control drawing (document number

000160011DNR) on the following pages.

Relevant for Europe

for devices installed in explosive gas atmospheres according to ATEX

directive 2014/34/EU:

Make sure that the device has the following label:

II 3G (... followed by additional specifications).

Note: Observe the control drawing (document number

000160011DNR) on the following pages.

Avertissement - Risque d'explosion - Ne pas débrancher tant que le

circuit est sous tension à moins que l'emplacement soit connu pour ne

contenir aucune concentration de gaz inflammable.

Avertissement - Risque d'explosion - La substitution de tout composant

peut rendre ce matériel incompatible pour une utilisation en classe I,

division 2.

Installation MS20/MS30

Release

09/2019 7

CONTROL DRAWING for Industrial ETHERNET Rail Switch MS20 and MS30 devices

943

-435-999 according to the directive 2014/34/EU

or Class I Division 2 Hazardous Locations

Version: 3

Document No.: 000160011DNR

Page 1/4

Ordinary Location,

Non-

Hazardous Area,

non-explosive

atmosphere

WARNING! The USB connection and the V.24

Interface connection are for temporary

connection only, for maintenance use. Do not

use, connect or disconnect unless the area is

known to be non

-hazardous. Connection or

disconnection in an explosive atmosphere could

result in an explosion!

Relay

The earth conductor must be at

least the same wire size (mm²

or AWG) as the supply

conductors.

Power Supply range “C” (P1, P2 Redundant)

18 –60 VDC;

4.0 –1.2 A; max. 72

Relay contacts:

Equipment with nonincendive field wiring

parameters.

Polarity is not relevant.

THE RELAY TERMINALS ARE DEPENDENT

UPON THE FOLLOWING ENTITY

PARAMETERS:

)

Temperature Code: T4

Ambient Temperature rating:

Ta:

0 °C to +60 °C for “S” types

Ta:

-40 °C to +70 °C for “T” or “E” types

– refer to the type designation on the device

(Position 10 of nomenclature: “Temperature

range”).

MS20/30 switch basic module

with voltage range type “C”

Zone 2: Explosive Atmosphere

or Class I, Division 2,

Groups A, B, C, D

Hazardous Location

30 V

90 mA

2 nF

1 µH

8Installation MS20/MS30

Release

09/2019

CONTROL DRAWING for Industrial ETHERNET Rail Switch MS20 and MS30 devices

943

-435-999 according to the directive 2014/34/EU

or Class I Division 2 Hazardous Locations

Version: 3

Document No.: 000160011DNR

Page 2/4

WARNING! The USB connection and the V.24

Interface connection are for temporary

connection only, for maintenance use. Do not

use, connect or disconnect unless the area is

known to be non

-hazardous. Connection or

disconnection in an explosive atmosphere could

result in an explosion!

Relay

Power Supply range “A” (P1, P2 Redundant)

18 –32 VDC;

4.0 –2.25 A; max. 72 W

Temperature Code: T4

Ambient Temperature rating:

: 0°C to +60°C for “S” types

Ta:

-40°C to +70°C for “T” or “E” types

– refer to the type designation on the device

(Position 10 of nomenclature: “Temperature r

ange”).

Zone 2: Explosive

Atmosphere

or Class I Division 2

Groups A, B, C, D

Hazardous Location

Ordinary Location,

Non-

Hazardous Area,

non-

explosive atmosphere

The earth conductor must be at

least the same wire size (mm²

or AWG) as the supply

conductors.

MS20/30 switch basic module

with voltage range type “A”

Relay contacts:

Equipment with nonincendi

ve field wiring

parameters.

Polarity is not relevant.

THE RELAY TERMINALS ARE DEPENDENT

UPON THE FOLLOWING ENTITY

PARAMETERS:

)

30 V

90 mA

2 nF

1 µH

Installation MS20/MS30

Release

09/2019 9

For Use in explosive atmospheres under the European directive 2019/34/EU:

Applied Standards: EN 60079-0: 2012 + A11: 2013

EN 60079-15: 2010

EN 60079-11: 2012

The Use in Hazardous Locations with explosive atmospheres is only allowed for MS20 or MS30 model

No´s. which are individually labelled

“8 II 3G” and “Ex nA ic IIC T4 Gc” and “DEKRA 13 ATEX 0019X” for MSxx devices,

“8 II 3G” and “Ex nA IIC T4 Gc” and “DEKRA 13 ATEX 0019X” for MB20 devices.

Special conditions for safe use

1. The modules shall be installed in a suitable enclosure in accordance with EN60079-15, taking into

account the environmental conditions under which the equipment will be used.

2. Provisions shall be made to prevent the rated voltage from being exceeded by transient

disturbances of more than 119 V.

3. When the temperature under rated conditions exceeds +70 °C at the cable or conduit entry point, or

+80 °C at the branching point of the conductors, the temperature specification of the selected cable

shall be in compliance with the actual measured temperature values.

Note

The nonincendive field wiring circuit concept allows interconnection of nonincendive field

wiring apparatus and associated nonincendive field wiring apparatus using any of the wiring

methods permitted for unclassified locations when certain parametric conditions are met.

Capacity: C

≥ C

+ C

Cable

; Inductivity: L

≥ L

+ L

Cable

The maximum cable length has to be determined as follows:

(a) max. Cable Length < (L

) / Cable

(“Cable

” denotes the inductance per unit length of used cable) and

(b) max. Cable Length < (C

) / Cable

(“Cable

C”

denotes the capacitance per unit length of used cable).

The lower value of (a) and (b) is to apply.

Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH.

DOM: ww/yyyy (Date of manufactur: w - week, y - year. Refer to the device label).

CONTROL DRAWING for Industrial ETHERNET Rail Switch MS20 and MS30 devices

943

-435-999 according to the directive 2014/34/EU

or Class I Division 2 Hazardous Locations

Rev.: 3

Document No.: 000160011DNR

Page 3/4

10 Installation MS20/MS30

Release

09/2019

For Use in Hazardous Locations Class I Division 2 Groups A, B, C, D:

Applied standard: ANSI/ISA 12.12.01-2011.

Only allowed for MS20 or MS30 model No´s. which are individually labelled

“FOR USE IN HAZARDOUS LOCATIONS”

Nonincendive field wiring circuits must be wired in accordance with the

National Electrical Code (NEC), NFPA 70, article 501.

WARNING –EXPLOSION HAZARD –SUBSTITUTION OF ANY COMPONENTS MAY

IMPAIR SUITABILITY FOR HAZARDOUS LOCATIONS OR EXPLOSIVE

ATMOSPHERES.

WARNING –EXPLOSION HAZARD –DO NOT DISCONNECT EQUIPMENT UNLESS

POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-

HAZARDOUS.

Use 60/75 or 75 °C copper (CU) wire only.

Only for connection to a Class 2 power supply.

Note 2):

The nonincendive field wiring circuit concept allows interconnection of nonincendive field

wiring apparatus and associated nonincendive field wiring apparatus using any of the

wiring methods permitted for unclassified locations when certain parametric conditions are

met.

Capacity: Ca≥ Ci+ CCable ; Inductivity: La ≥ Li+ LCable

The maximum cable length has to be determined as follows:

(a) max. Cable Length < (La -Li) / Cable L

(“Cable L”denotes the inductance per unit length of used cable) and

(b) max. Cable Length < (Ca -Ci) / Cable C

(“Cable C” denotes the capacitance per unit length of used cable).

The lower value of (a) and (b) is to apply.

Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control

GmbH.

DOM: ww/yyyy (Date of manufactur: w - week, y - year. Refer to the device label).

CONTROL DRAWING for Industrial ETHERNET Rail Switch MS20 and MS30 devices

943

-435-999 according to the directive 2014/34/EU

or Class I Division 2 Hazardous Locations

Rev.: 3

Document No.: 000160011DNR

Page 4/4

Autres manuels pour Hirschmann MICE MS20

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Belden Changer

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden MAMMUTHUS MTM2800-PSU120 Manuel utilisateur

Belden

Belden Hirschmann Rail Switch Power Lite Manuel utilisateur

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden HIRSCHMANN EESX Series Guide de configuration rapide

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden grass valley MASTERPIECE 12G-SDI Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Manuel utilisateur

Belden

Belden HIRSCHMANN MACH 100 Series Manuel utilisateur

Belden

Belden HIRSCHMANN PTN-CSM310-A Manuel utilisateur

Belden

Belden HIRSCHMANN MACH 4000 Series Manuel utilisateur

Belden

Belden grass valley GV FABRIC Manuel utilisateur

Belden

Belden HIRSCHMANN RSP20 Manuel utilisateur

Belden

Belden HIRSCHMANN RSPE 30 Manuel utilisateur

Belden

Belden Thinklogical TLX48 Manuel utilisateur

Belden

Belden Hirschmann MACH1040 Series Manuel utilisateur

Belden

Belden Hirschmann MACH1000 Series Manuel utilisateur

Belden

Belden Hirschmann GREYHOUND GRS1042 Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden HIRSCHMANN GRS105 Manuel utilisateur

Belden

Belden Hirschmann SPIDER 8TX EEC Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur