Atmel ATAK2270 Manuel utilisateur

4871E–RFID–04/08

RFID Application Kit ATAK2270

....................................................................................................................

User Manual

RFID Application Kit ATAK2270 User Manual i

4871E–RFID–04/08

Table of Contents

Section 1

Introduction.................................................................................................................1-1

1.1 RFID Products Promoted by ATAK2270 Kit ...................................................................... 1-1

1.2 Included Hardware Components ....................................................................................... 1-1

1.3 Equipment Needed ............................................................................................................ 1-1

Section 2

Getting Started ...........................................................................................................2-1

2.1 Hardware Settings and Connector Positions ..................................................................... 2-1

2.2 Software Installation........................................................................................................... 2-3

2.2.1 AVR Programming Guide .................................................................................... 2-3

Section 3

Description of the Application Board System .............................................................3-1

3.1 System Overview............................................................................................................... 3-1

3.2 Power Supply..................................................................................................................... 3-1

3.3 Antenna Interface............................................................................................................... 3-1

3.3.1 Frequency Tuning Mode Selection...................................................................... 3-2

3.3.2 RF Field Control................................................................................................... 3-2

3.3.3 Antenna Interface Parts List ................................................................................ 3-4

Section 4

Basic Transponder Functionality Getting Started.......................................................4-1

4.1 System Installation............................................................................................................. 4-1

4.2 Checking Simple Transponder Function............................................................................ 4-1

Section 5

Host Software.............................................................................................................5-1

5.1 Software Structure ............................................................................................................. 5-1

5.2 Start Window...................................................................................................................... 5-2

5.2.1 Setup ................................................................................................................... 5-2

5.2.2 Options ................................................................................................................ 5-2

5.2.3 Application ........................................................................................................... 5-3

5.2.4 Exit.......................................................................................................................5-5

5.2.5 Info.......................................................................................................................5-5

Table of Contents (Continued)

ii RFID Application Kit ATAK2270 User Manual

4871E–RFID–04/08

5.3 Transponder Type Software Interface Description ............................................................ 5-6

5.3.1 TK5530/e5530 Read-only Transponder Menu .................................................... 5-6

5.3.2 TK5552/T5552 Read/Write Transponder............................................................. 5-7

5.3.3 TK5551 Read/Write Transponder........................................................................ 5-9

5.3.4 T5557/ATA5567 Multifunction Read/Write Transponder................................... 5-11

5.3.5 ATA5570 Multifunction Read/Write Transponder with Sensor Input ................. 5-15

5.3.6 ATA5577 Enhanced Read/Write Transponder with AFE-Options ..................... 5-16

5.4 Operating Common Transponder Features..................................................................... 5-23

5.4.1 Password PWD Mode........................................................................................ 5-23

5.4.2 Answer On Request AOR Mode........................................................................ 5-24

5.4.3 Readout Manufacturer (Traceability) Data......................................................... 5-25

RFID Application Kit ATAK2270 User Manual 1-1

4871E–RFID–04/08

Section 1

Introduction

1.1 RFID Products Promoted by ATAK2270 Kit

The RFID application kit (ordering code ATAK2270) promotes the key features of various RFID products

from Atmel®.

The following products are supported by the kit:

U2270B Read/write base station IC

TK5530/e5530 Read-only transponder

TK5551 Standard read/write transponder

TK5552/T5552 Read/write transponder micromodule with 1-Kbit memory

T5557/ATA5567 Multifunctional read/write transponder

ATA5570 Multifunctional read/write transponder with sensor input

ATA5577 Enhanced read/write transponder

1.2 Included Hardware Components

Microcontroller board with piggybacked antenna board

Reader antenna coil 100 mm∅, L = 700 µH, Q = 36

Serial communication cable RS232

Jack connector cable for power supply

Power supply 120V to 240V

Installation software and documentation on CD-ROM

Atmel Standard Products CD-ROM

IC samples (3 pieces of each): U2270B-MFP; TK5530-HM232-PP; TK5551M-PP; TK5552A-PP;

T555711-TAS; T555715-PAE; ATA556711-TAS; ATA556715-PAE; ATA5570-TAS; ATA5577Mxxx-xx;

ISO Card ATA556715-PAE; Coin Tag ATA556715-PAE

Transponder SMD antenna coil SDTR 1103, 4.77 mH, Q = 25 (Manufacturer: Predan)

Transponder test board ATAB5570 with sensor input

1.3 Equipment Needed

Host PC with Windows®95 or higher

RFID Application Kit ATAK2270 User Manual 2-1

4871E–RFID–04/08

Section 2

Getting Started

Build up the RFID reader application system according to the configuration shown on the cover and in

Figure 2-1:

1. Plug the antenna into the socket of the interface board.

2. Connect a serial RS232 cable between the RS232 connector and either COM1 or COM2 of the PC.

3. Connect the supply line from the 12V power source to the jack connector. Alternatively use the

mains SMPS.

2.1 Hardware Settings and Connector Positions

The main board with the AVR®ATmega8515L controls piggiybacked reader interface and maintains the

communication with the host. On delivery the AVR is fleshed with the current firmware and does not

need any special programming or settings. Check that jumper J3 on the antenna interface is in the

default position en.

Figure 2-1. Application Board Unit

Getting Started

2-2 RFID Application Kit ATAK2270 User Manual

4871E–RFID–04/08

Figure 2-2. Antenna Interface Board

Figure 2-3. Application Board Top View

Getting Started

RFID Application Kit ATAK2270 User Manual 2-3

4871E–RFID–04/08

2.2 Software Installation

The ATAK2270 host installation software as well as the related datasheets and documentation are pro-

vided by the CD-ROM included in the kit. Furthermore, the up-to-date software and documentation are

available via the web.

Execute the setup.exe file found on the CD-ROM to launch the installation and generate the

ATAK2270.exe program file. If the default settings are accepted during installation, the program file will

be installed to path: X:\Programme\ATAK2270\ATAK2270.exe.

Note: Administrator rights are required to install this software.

2.2.1 AVR Programming Guide

The AVR base board (Figure 2-3) is equipped with two programming interfaces, ISP and JTAG allowing

reprogramming or updating the firmware of AVR flash memory.

ISP is a downloading method. Only six I/O lines are needed. The provided header works with the

ATSTK500 as well as the AVR ISP In-System Programmer. Both of these are available from Atmel or

distributors for very low cost program development. To program the flash memory and the EEPROM,

first connect the programming tool to the MB using a six-pin ribbon connector. Make sure that proper ori-

entation is maintained by aligning pin1. The files types accepted use Intel Hex format.

To program a hex file into the target AVR device, select “Program AVR” and then “Connect...” from the

“Tools” menu in AVR Studio. Once AVR Studio has been opened, connect to the STK500 or AVRISP by

selecting “STK500 or AVRISP” in the Platform List. Then select “Connect...”. The driver for the STK500

and AVRISP is then started, and the STK500 dialog should appear. Note that the system supports other

programming platforms as well, like the JTAGICE or the JTAGICE mkII.

Then select the AVR target device from the pull-down menu on the “Program” tab and locate the Intel-

hex file to download. Select the “program” button. Repeat for the EEPROM section.

The same steps apply when using the JTAGICE MKII.

The JTAG Platform allows more control during software development by allowing real-time debugging of

the source code. The JTAGICE MKII supports setting breakpoints and stepping through the code being

executed on the target micro. This is very useful for a more complex software project such as this one.

Fuse Settings:

Fuse bits must be set properly for the kit to function. The only fuse bits that should be set are listed

below.

JTAG Interface Enabled; (JTAGEN = 0)

Serial program downloading (SPI) enabled; (SPIEN = 0)

Boot Flash section size = 512 words Boot start address = $FE00; (BOOTSZ = 11)

Brown-out detection level at VCC = 2.7V; (BODLEVEL = 1)

Int. RC OSC. 8MHz; Start-up time; 6CK + 64 ms; (CKSEL = 0100 SUT = 10)

All others should be unchecked.

RFID Application Kit ATAK2270 User Manual 3-1

4871E–RFID–04/08

Section 3

Description of the Application Board System

3.1 System Overview

The ATAK2270 application board unit (Figure 2-3) consists of a ready-to-run standard microcontroller

main board equipped with the Atmel AVR®microcontroller ATmega8515L, combined with a piggybacked

antenna interface board containing the U2270B reader IC.

The following functionality is controlled by the AVR microcontroller:

Handling of the bi-directional data communication between the RS232 interface and the host PC

Execution of the read and write commands to be sent to the antenna interface

Decoding of the specific read data delivered by the antenna interface

The source program is written in C, and the compiled hex code is loaded in the 8-kByte Flash of the

microcontroller.

3.2 Power Supply

To operate the reader board, an external power supply in the range of DC 10V to 15V/200 mA has to be

connected to the jack, alternatively use the mains SMPS. A bridge rectifier placed at the connector input

is used for polarity independence.

3.3 Antenna Interface

The antenna interface (Figure 2-2) is supplied and controlled by the main board via header pin X2/1. The

current power supply voltage is indicated by LED1, Power. To adapt a specific antenna coil to the reso-

nant frequency and the Q factor, the components CANT1/CANT2 and R14 (Figure 2-2) can be changed.

For the antenna included in the kit, the parameters are matched as follows:

Resonant frequency: fres = 125 kHz ±1%, adjusted by CANT1/CANT2 with jumper 3 in

position dis

Whole antenna quality factor: Q = 20, adjusted by R14

Description of the Application Board System

3-2 RFID Application Kit ATAK2270 User Manual

4871E–RFID–04/08

3.3.1 Frequency Tuning Mode Selection

The reader interface has a built-in frequency tuning feature. By the host software, the resonant fre-

quency of the LC antenna circuit can be switched in four steps. Therefore the board is equipped with two

stages of high-voltage transistor switches to tune the resonator via switched capacitors.

In default setting Tuning Mode is activated, allowing the adjusting of antenna frequency by host menu.

The binary control of the two tuning stages enables the selection of one out of four frequency states.

According to the menu definition the frequency steps are designated as follows:

High Frequency 134.2 kHz (acc. ISO11784/85)

Semi High Frequency 130 kHz

Semi Low Frequency 125 kHz

Low Frequency 121 kHz

In disabled mode, the interface operates with the fixed frequency adjusted typically to 125 kHz.

The currently selected frequency stage is displayed on the application board by the red LEDs Tune 1

and Tune 2 (shown in Figure 2-2, see Table 5-1 for interpretation).

3.3.2 RF Field Control

The status of the RF field controlled by the microcontroller is indicated by the yellow LED RF on.

Table 3-1. The Frequency Tuning Can Be Selected Using Jumper J3

Tuning Mode Jumper J3 Position

Disabled 1-2

Enabled 2-3

Description of the Application Board System

RFID Application Kit ATAK2270 User Manual 3-3

4871E–RFID–04/08

Figure 3-1. Circuit Diagram of the Antenna Interface

CTUNE1

BF820

R18

BAS21

CTUNE2

Components for tuning application

BF820

R10

R11

R17

R16

R21

R19 R20

R22

R13

R14

R12

BAS21

M14 Antenna

M13

CANT1

Components

for feedback

application

BAV21

X1/6

X2/5

X1/3

X2/10

X2/9

X1/11

X1/7

X2/1

Green

VEXT

VBATT

Power

DZ1

LD1

DVS

COIL1

COIL2

INPUT

Data in

M12

Data out

IN OUT

VCC

Red

TUNE2

LD3

Yellow

RFon

LD4

M1 M4 MS

514 15

OUTPUT

CFE

GND

DGND

HIPASS

STANDBY

M15

M11

7808

U2 RF

CANT2

Red

TUNE1

LD2

R15

Table des matières

Autres manuels Atmel Matériel informatique

Atmel

Atmel AT73C246-EK1 Manuel utilisateur

Atmel

Atmel ATWINC3400 Manuel utilisateur

Atmel

Atmel STK501 Manuel utilisateur

Atmel

Atmel AT91SAM7L-STK Manuel utilisateur

Atmel

Atmel AT89C5132 Manuel utilisateur

Atmel

Atmel AT90ICEPRO Manuel utilisateur

Atmel

Atmel AT86RF211 Manuel utilisateur

Atmel

Atmel AT90USB162 Manuel utilisateur

Atmel

Atmel AT91CAP9 Manuel utilisateur

Atmel

Atmel STK502 Manuel utilisateur

Atmel

Atmel FPSLIC AT94KAL Series Manuel utilisateur

Atmel

Atmel SAM9X25 Manuel utilisateur

Atmel

Atmel ATDH2200E Manuel utilisateur

Atmel

Atmel 8-bit AVR Microcontrollers AVR430: MC300 Manuel utilisateur

Atmel

Atmel AVR XMEGA 8/16-bit High Performance Low Power Flash... Manuel utilisateur

Atmel

Atmel ATSAMB11 BluSDK SMART Manuel utilisateur

Atmel

Atmel I/O1 Xplained Pro Manuel utilisateur

Atmel

Atmel AT24C16C Manuel utilisateur

Atmel

Atmel ATAN0008 Manuel utilisateur

Atmel

Atmel AVR ATmega324PA Manuel utilisateur

Atmel

Atmel Microcontroller with LIN Transceiver ATA6602 Manuel utilisateur

Atmel

Atmel ATSAMD21BLDC24V-STK Manuel utilisateur

Atmel

Atmel AVR364 Manuel utilisateur

Atmel

Atmel ATmega8535L Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur