Atmel ATBTLC1000 BluSDK Manuel utilisateur

ATBTLC1000 BluSDK

Find Me Profile - Getting Started Guide

USER GUIDE

Introduction

This getting started guide describes the setup of the Atmel®ATBTLC1000 with a supported platform

bringing-up an example profile supplied as part of BluSDK release. The Bluetooth®Find Me Profile is an

example application that is embedded as part of the software release package.

The Find Me Profile (FMP) defines the behavior when a button is pressed on one device to cause an

alerting signal on a peer device.

This document explains the details about:

1. Getting started with the setup of supported platform to be used as a Find Me Target.

2. Getting the Find Me Application working on the above mentioned setup.

Features

Device Discovery and Disconnection

Pairing / Bonding

Find Me Alerts

Console Display

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

Table of Contents

1Demo Setup..................................................................................................................3

2Supported Hardware Platforms and IDEs ..................................................................3

3Hardware Setup ...........................................................................................................4

3.1 SAM L21 Xplained Pro Find Me Target Setup.......................................................................................4

3.2 SAM D21 Xplained Pro Find Me Target Setup......................................................................................4

3.3 SAM G55 Xplained Pro Find Me Target Setup......................................................................................5

3.4 SAM 4S Xplained Pro Find Me Target Setup........................................................................................5

4Find Me Target.............................................................................................................6

5Software Setup.............................................................................................................6

5.1 Installation Steps...................................................................................................................................6

5.2 Build Procedure.....................................................................................................................................6

6Console Logging .......................................................................................................10

7Running the Demo.....................................................................................................10

8BluSDK Software Architecture..................................................................................13

9ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........14

10 Revision History ........................................................................................................15

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

1 Demo Setup

Figure 1-1. Demo Setup for Find Me Profile

2 Supported Hardware Platforms and IDEs

Table 2-1. BluSDK –Supported Hardware and IDEs

Platform

MCU

Supported

BLE Module

Supported evaluation kits

Supported IDEs

SAM L21 (MCU)

ATSAML21J18B

ATBTLC1000

ATBTLC1000-XSTK

(ATSAML21-XPRO-B + ATBTLC1000

XPRO)

Atmel Studio v7.0

SAM L21 (MCU)

ATSAML21J18A

ATBTLC1000

ATSAML21 XPRO + ATBTLC1000

XPRO

Atmel Studio v7.0

SAM D21 (MCU)

ATSAMD21J18A

ATBTLC1000

ATSAMD21-XPRO + ATBTLC1000

XPRO

Atmel Studio v7.0

SAM G55 (MCU)

ATSAMG55J19

ATBTLC1000

ATSAMG55-XPRO + ATBTLC1000

XPRO

Atmel Studio v7.0

SAM 4S (MCU)

ATSAM4SD32C

ATBTLC1000

ATSAM4S-XPRO + ATBTLC1000

XPRO

Atmel Studio v7.0

iPhone/Android

Atmel Smart Connect App

(Find Me Locator)

ATBTLC1000+

Supported Atmel MCU

(Find Me Target)

BLE Link

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

3 Hardware Setup

3.1 SAM L21 Xplained Pro Find Me Target Setup

Figure 3-1. ATBTLC1000 Xplained Pro Extension Connected to a SAM L21 Xplained Pro

3.2 SAM D21 Xplained Pro Find Me Target Setup

Figure 3-2. ATBTLC1000 Xplained Pro Extension Connected to a SAM D21 Xplained Pro

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

3.3 SAM G55 Xplained Pro Find Me Target Setup

Figure 3-3. ATBTLC1000 Xplained Pro Extension Connected to a SAM G55 Xplained Pro

3.4 SAM 4S Xplained Pro Find Me Target Setup

Figure 3-4. ATBTLC1000 Xplained Pro Extension Connected to a SAM 4S Xplained Pro

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

4 Find Me Target

The Find Me profile defines the behavior when a button is pressed on a device to cause an immediate

alert on a peer device. This can be used to allow users to find devices that have been misplaced.

Find Me Target Application which is the GATT server will hold the characteristics and wait for the Find Me

locaters alerts and based on the alerts level it will do the appropriate task.

Alert Level Characteristic

When the Find Me Locator device wishes to cause an alert on the Find Me Target device, it shall write the

specific Alert Level in the Alert Level characteristic.

5 Software Setup

5.1 Installation Steps

1. Atmel Studio installation [Atmel Studio 7.0 (build 594) Installer –with .NET]

http://www.atmel.com/tools/atmelstudio.aspx.

(Note: SAM L21 Rev B/SAM D21/SAM G55/SAM 4S part pack is built-in as part of Atmel Studio

7.0)

2. Atmel USB Driver Installer from http://www.atmel.com/tools/atmelstudio.aspx.

3. Install the standalone ASF package from

http://www.atmel.com/tools/AVRSOFTWAREFRAMEWORK.aspx .

Note: Refer to the BluSDK release notes for updates to version numbers of the components mentioned

above.

This package will install the following examples within the Atmel Studio environment.

1. Find Me Application for SAM L21.

2. Find Me Application for SAM D21.

3. Find Me Application for SAM G55.

4. Find Me Application for SAM 4S.

5.2 Build Procedure

The following procedure is explained for SAM L21 application example. The same procedure is valid for

the case of all the other supported platform as well.

Select New Example Project.

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

Figure 5-1. Creating a New Project

1. Select “SAML,32-bit” in device family, enter “Find Me” in search window and expand Atmel Corp.

Projects. The location and the name of the project can be selected in the respective fields. Click OK.

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

Figure 5-2. Selecting Find Me Application from Example Projects

2. Accept the license Agreement. The studio will generate the Find Me Target project for SAM L21.

3. Build the solution.

Figure 5-3. Building the Find Me Application

4. Download the application via the USB to the SAM L21 board by using the Device Programming

option available in Tools as mentioned below.

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

Figure 5-4. Programming the Find Me Application

5. Inside device programming the user has to select the correct configuration for the device and finally

program the device by using the program button.

Figure 5-5. Flashing the Find Me Application

6. Once the application is flashed the Find Me Target Application is ready for usage.

ATBTLC1000 BluSDK Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42545C-ATBTLC1000-BluSDK-Find-Me-Profile-Getting-Started-Guide_UserGuide_022016

6 Console Logging

For the purpose of debugging, a logging interface has been implemented in the Find Me Application.

The logging interface utilizes the same EDBG port that connects to the supported platform. A serial port

monitor application (for example TeraTerm) shall be opened and attached to the corresponding COM port

enumerated on the PC by the device. The baud rate should be set to 115200.

7 Running the Demo

1. Power on the SAM L21 + ATBTLC1000 setup by connecting the USB cable as indicated in Figure

3-1.

2. Open a console window using TeraTerm or any equivalent serial port monitor application and

connect to the corresponding COM port enumerated on the PC. (Settings: Baud rate 115200, None

Parity, one Stop bit, one Start bit, no Hardware Handshake.)

3. Press the Reset button on the SAM L21 or supported platform board.

4. The device is now in advertising mode.

Figure 7-1. Console Display for Device in Advertisement Mode

5. On a BLE compatible Android phone or an iPhone®, enable Bluetooth in the Settings page. Start the

Atmel Smart Connect App and scan for devices. ATMEL-FMP will be appear amongst the devices

scanned. Click on ATMEL-FMP to connect to the SAM L21 or supported platform + ATBTLC1000

device.

Autres manuels pour ATBTLC1000 BluSDK

Table des matières

Autres manuels Atmel Matériel informatique

Atmel

Atmel SAM W25 Xplained Pro Manuel utilisateur

Atmel

Atmel ATSAMB11 BluSDK SMART Manuel utilisateur

Atmel

Atmel AT76C502A Manuel utilisateur

Atmel

Atmel AVR2016 Manuel utilisateur

Atmel

Atmel REB233-XPRO Manuel utilisateur

Atmel

Atmel SAMDA1 Xplained Pro Manuel utilisateur

Atmel

Atmel AVR ATmegaICE Manuel utilisateur

Atmel

Atmel ATSAMB11 BluSDK SMART Manuel utilisateur

Atmel

Atmel AT91CAP9 Manuel utilisateur

Atmel

Atmel AT89STK-06 CAN Manuel d'installation

Atmel

Atmel I/O1 Xplained Pro Manuel utilisateur

Atmel

Atmel 8-bit AVR Microcontrollers AVR430: MC300 Manuel utilisateur

Atmel

Atmel ATAK5276-83 Instructions d'installation et d'utilisation

Atmel

Atmel AVR364 Manuel utilisateur

Atmel

Atmel AT91MEC01 Manuel utilisateur

Atmel

Atmel AT04357 RCB256RFR2-XPRO Manuel utilisateur

Atmel

Atmel ATAK2270 Manuel utilisateur

Atmel

Atmel FPSLIC AT94KAL Series Manuel utilisateur

Atmel

Atmel ATF16V8B Manuel utilisateur

Atmel

Atmel AT91SAM-ICE Manuel utilisateur

Atmel

Atmel ATmega8535L Manuel utilisateur

Atmel

Atmel STK501 Manuel utilisateur

Atmel

Atmel STK502 Manuel utilisateur

Atmel

Atmel SAMA5D3 Series-EK Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur