Atdec AWM-LR Manuel utilisateur

AWM-LR Page 1 of 4

Installation Guide

AWM-LR

Dual Crossbar

COMPONENT CHECKLIST

REQUIRED TOOLS

• Phillips Head Screwdriver

Crossbar

Assembly

(x1)

VESA Plate

(x2)

Handle

(x1)

Screw

M4x10mm

(x8)

Screw

M4x12mm

(x8)

Screw

M4x16mm

(x8)

Plastic

Washer

(x2)

Hole

Cap

(x2)

Screw

M6x12mm

(x2)

Security

Screw

(x2)

4mm

Allen Key

(x1)

3mm

Allen Key

(x1)

2 - 7kg

(4.5 - 15lbs)

per monitor

WEIGHT RANGE

Monitor weight should be

within the weight range of

all modular elements that

make up the complete

monitor mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed

the capacity of the mount even though the monitor weight may be within the stated range.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with AWM Series monitor arm products.

AWM-LR Page 2 of 4

3. Attach VESA plates to monitors

3.2 Ensure suitable screw length is used. 3.3 VESA mounting compatibility

Note: For other sizes, use

a suitable adaptor plate

3.1 Screw VESA plates onto the monitors.

100mm

75mm

100mm 75mm

1. Mount crossbar onto arm

2. Attach handle (Optional)

1.1 Push crossbar onto shaft at end of arm.

2.1 Use the 4mm allen key to loosely fasten

the handle onto the crossbar.

2.2 Adjust handle to a height that suits the

monitors, then tighten the two screws.

2.3 If not using handle t hole caps.

1.3 Tighten joint

screw to secure

rail to arm.

Too short Too long

Note: Check the crossbar rotation

is smooth after tightening.

1.2 Ensure crossbar is fully pushed

onto shaft.

M6x12

Screw

Plastic

Washer

AWM-LR Page 3 of 4

5. Adjust the ball joint tension

6. Install Cables

5.1 If the monitors are not

holding position or are sti

to move, adjust the tension

plate by tightening or

loosening the three screws.

Note: Adjust 3

screws evenly in

small increments

Note: Support the monitor

while making adjustments.

4. Mount monitors onto crossbar

4.1 Hook the top of the VESA plate onto

the ball joint mount.

4.2 Gently push the bottom of the monitor

until the VESA plate locks into place.

4.3 OPTIONAL security screw

Tilt the monitor upwards to install the

security screw.

Repeat steps 4.1 to 4.3

for second monitor

Tilt Up

Push

Click

Hook

3mm

Allen Key

Important!

Ensure enough cable slack is given to

allow for movement of the monitors.

AWM-LR Page 4 of 4

Push

Loosen

Tighten

8. Adjust level of crossbar

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

8.1 Rotate the crossbar so that it sits

parallel to the worksurface.

+/- 5°

OPTIONAL If the crossbar rotation is too loose or

sti, adjust the tension screw under the centre of

the crossbar.

ANGLEDFLAT

7. Adjust horizontal position of monitors

9. Adjust monitor angle

7.1 Slide the monitors along the crossbar until they are

positioned centrally in the desired position.

7.2 Monitors can also be rotated to portrait position.

Autres manuels Atdec Support et étagère

Atdec

Atdec Spacedec SD-POS-VBM-B2B Manuel utilisateur

Atdec

Atdec VFS-Q Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AF-AT Manuel utilisateur

Atdec

Atdec SD-AT-DW Manuel utilisateur

Atdec

Atdec AWMS-3-137140-C Manuel utilisateur

Atdec

Atdec AD-WFP-5040 Manuel utilisateur

Atdec

Atdec AF-ATC Manuel utilisateur

Atdec

Atdec VFS-DV Manuel utilisateur

Atdec

Atdec AWMS-DW Manuel utilisateur

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AD-TVC-70R Manuel utilisateur

Atdec

Atdec AWM 710 Arm Manuel utilisateur

Atdec

Atdec AWM-LTH Manuel utilisateur

Atdec

Atdec VISIDEC FOCUS MICRO Instructions de fonctionnement

Atdec

Atdec AWM-HS Manuel utilisateur

Atdec

Atdec VFS-Q Manuel utilisateur

Atdec

Atdec AWM 460 Arm Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec TH-2050-VFM Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-FS Manuel utilisateur

Atdec

Atdec TH-1026-VF Manuel utilisateur

Atdec

Atdec 8060 Manuel utilisateur

Atdec

Atdec TH-1040-CTS Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur