AEMC instruments 5070 Manuel utilisateur

5070

User Manual

ENGLISH

MEGOHMMETERS

WITH AEMC

INSTRUMENTS

No part of this documentation may be reproduced in any form or by any means (including electronic

storage and retrieval or translation into any other language) without prior agreement and written consent

from Chauvin Arnoux®, Inc., as governed by United States and International copyright laws.

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive • Dover, NH 03820 USA

Tel: (800) 945-2362 or (603) 749-6434 • Fax: (603) 742-2346

This documentation is provided “as is,” without warranty of any kind, express, implied, or otherwise.

Chauvin Arnoux®󰀨

but does not warrant the accuracy or completeness of the text, graphics, or other information contained

in this documentation. Chauvin Arnoux®, Inc. shall not be liable for any damages, special, indirect,





user of the documentation has been advised of the possibility of such damages.

Statement of Compliance

Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments

certiﬁes that this instrument has been calibrated using

standards and instruments traceable to international

standards.

We guarantee that at the time of shipping your

instrument has met its published speciﬁcations.

An NIST traceable certiﬁcate may be requested at

the time of purchase, or obtained by returning the

instrument to our repair and calibration facility, for

a nominal charge.

The recommended calibration interval for this

instrument is 12 months and begins on the date of

receipt by the customer. For recalibration, please

use our calibration services. Refer to our repair and

calibration section at www.aemc.com.

Serial #:

Catalog #: 2130.30

Model #: 5070

Please ﬁll in the appropriate date as indicated:

Date Received:

Date Calibration Due:

Chauvin Arnoux®, Inc.

d.b.a AEMC®Instruments

www.aemc.com

TABLE OF CONTENTS

1. INTRODUCTION ................................................................................ 6

1.1 PRECAUTIONS FOR USE........................................................ 7

1.2 RECEIVING YOUR SHIPMENT................................................ 7

1.3 ORDERING INFORMATION ..................................................... 8

1.3.1 Accessories and Replacement Parts .............................................8

1.4 ACCESSORY INFORMATION .................................................. 8

1.4.1 DataView®Software .......................................................................8

2. PRODUCT FEATURES...................................................................... 9

2.1 DESCRIPTION ........................................................................... 9

2.1.1 Control Features ..........................................................................10

2.2 DISPLAY FEATURES .............................................................. 12

3. SPECIAL FUNCTIONS.................................................................... 13

3.1 SET-UP FUNCTION................................................................. 13

..................................................................13

 ..........................................14

3.1.3 SET-UP Menu ..............................................................................21

3.2 MODE / PRINT BUTTON......................................................... 22

3.2.1 Primary Function - MODE............................................................22

3.2.2 Secondary Function - PRINT .......................................................26

3.3 DISPLAY / GRAPH BUTTON .................................................. 26

3.3.1 Primary Function - DISPLAY........................................................26

3.3.2 Secondary Function - GRAPH .....................................................39

.................................................................. 39

 ..................................................................39

3.4.2 Secondary Function - TEMP........................................................39

 ........................................................... 41

 ...................................................................41

3.5.2 Secondary Function - SMOOTH ..................................................41

 ............................................................... 42

 ...................................................................42

3.6.2 Secondary Function - ALARM......................................................42

 BUTTON ...................................................................... 42

 ...................................................................42

3.7.2 Secondary Function - ............................................................42

3.8 MEM / MR BUTTON................................................................. 42

3.8.1 Primary Function - MEM (Save)...................................................42

3.8.2 Second Function - MR (Recall)....................................................44

3.9 CLEARING THE MEMORY ..................................................... 44

.................... 46

3.11 MAXIMUM OUTPUT VOLTAGE ............................................ 47

3.12 LIST OF ERROR CODES...................................................... 47

4. MEASUREMENT FUNCTIONS....................................................... 48

4.1 AC/DC VOLTAGE ..................................................................... 48

4.2 INSULATION MEASUREMENT .............................................. 48

4.3 CAPACITANCE MEASUREMENT .......................................... 51

4.4 RESIDUAL CURRENT MEASUREMENT .............................. 51

5. OPERATION ..................................................................................... 52

5.1 PERFORMING MEASUREMENTS ........................................ 52

5.2 STEP FUNCTION MODE ........................................................ 53

5.3 OPERATION EXAMPLES........................................................ 55

6. DATAVIEW®SOFTWARE ................................................................ 57

6.1 INSTALLING DATAVIEW ......................................................... 57

6.2 MEGOHMMETER CONTROL PANEL .................................... 59

7. SPECIFICATIONS............................................................................ 60

7.1 REFERENCE CONDITIONS................................................... 60

7.2 VOLTAGE.................................................................................. 60

7.3 INSULATION RESISTANCE ................................................... 60

7.4 POWER SUPPLY ..................................................................... 65

7.5 ENVIRONMENTAL SPECIFICATIONS .................................. 65

7.6 MECHANICAL SPECIFICATIONS.......................................... 66

7.7 SAFETY SPECIFICATIONS.................................................... 66

7.8 VARIATIONS IN OPERATING RANGE .................................. 66

8. MAINTENANCE................................................................................ 67

8.1 RECHARGING THE BATTERY............................................... 67

8.2 FUSE REPLACEMENT............................................................ 67

8.3 CLEANING................................................................................ 67

8.4 STORAGE................................................................................. 68

8.5 REPAIR AND CALIBRATION .................................................. 68

8.6 TECHNICAL AND SALES ASSISTANCE ............................... 68

8.7 LIMITED WARRANTY.............................................................. 69

8.8 WARRANTY REPAIRS ............................................................ 69

APPENDIX A. UTILIZING THE GUARD TERMINAL........................ 70

APPENDIX B. V DISTURBANCE/V OUTPUT FEATURE................. 72

6 Megohmmeter Model 5070

1. INTRODUCTION

Thank you for purchasing a Megohmmeter Model 5070.

For best results from your instrument and for your safety, read the enclosed

operating instructions carefully and comply with the precautions for use. These



Symbols

Instrument is protected by double or reinforced insulation.

CAUTION, risk of DANGER! The operator must refer to the user manual

whenever this symbol appears.

Risk of electric shock. The voltage at the parts marked with this symbol may

be dangerous.

The CE Mark guarantees conformity with European directives and with

regulations covering EMC.





Low-Voltage Safety, Electromagnetic Compatibility, and the Restriction of

Hazardous Substances.

The trash can with a line through it means that in the European Union, the

product must undergo selective disposal for the recycling of electric and

electronic material in compliance with Directive WEEE 2002/96/EC.



CAT IV corresponds to measurements taken at the primary electrical supply (<1000 V).

Example: primary overcurrent protection devices, ripple control units, and meters.

CAT III corresponds to measurements taken in building installations at the

distribution level.

Example: distribution panel, circuit-breakers, machines, and xed industrial devices.

CAT II corresponds to measurements taken on circuits directly connected to

low-voltage installations.

Example: power supply to domestic electrical appliances and portable tools.

Megohmmeter Model 5070 7

1.1 PRECAUTIONS FOR USE

These safety warnings are provided to ensure the safety of personnel and proper

operation of the instrument.

■Do not attempt to perform any tests with these instruments until you have read

the instruction manual.

■Safety is the responsibility of the operator!

■Tests are to be carried out only on non-energized circuits! Check for live

circuits before making resistance measurements (safety check).

■High voltage is present, as is the sample connected to it. Anyone performing

or assisting in testing must follow all safety precautions to prevent electrical

shock to themselves and others.

■Use personal protective equipment where appropriate.

■When testing samples with a capacitive component, make sure they have

been properly discharged and are safe to touch. Dielectric insulation samples



energized.

■Do not use the megohmmeter in areas where explosive or ignitable substances

are present. The testing of electrical systems with a megohmmeter could create a

spark and cause a hazardous situation.

■Only use the leads that are supplied with the megohmmeter. If they are

defective or worn, replace before testing.

■This instrument can be used on installations rated for 1000 V, Category III.

1.2 RECEIVING YOUR SHIPMENT

■Match the contents with the ordering information.

■Notify your distributor of any missing items.

■

carrier and notify your distributor at once.

NOTE: Fully charge the instrument before use.

8 Megohmmeter Model 5070

1.3 ORDERING INFORMATION

Megohmmeter Model 5070............................................................. Cat. #2130.30

Includes extra large tool bag, set of three 10 ft (5 kV) leads (red/black/blue with

clips), one guard terminal jumper lead, USB cable type B, US 115 V power cord,

rechargeable battery pack, and a USB stick with DataView®software and user

manual.



Cable – PC RS-232, DB9 F/F 6 ft Null Modem Cable

(For meters without USB Port) ..........................................................Cat. #2119.45

Cable – 5 ft USB A-B........................................................................ Cat. #2140.46

Fuse – Set of 3, 0.1 A, 380 V, 5 x 20, .10 kA.....................................Cat. #2119.84

Bag – Extra Large Classic Tool Bag ................................................. Cat. #2133.73

Inverter – 12 VDC to 120 VAC, 200 Watt for Vehicle use................... Cat. #2135.43

Cable – Replacement 10 ft USB cable............................................. Cat. #2136.80

Lead – Replacement set of 3, 10 ft (5 kV) Color-coded Safety

with Clips (JUMPER LEAD NOT INCLUDED).................................. Cat. #2151.30

Lead – Replacement 1 ft Jumper Lead ............................................ Cat. #2151.31

Lead – Set of 3, 25 ft (5 kV) Safety with Clips.................................. Cat. #2151.32

Battery – Rechargeable 9.6 V .......................................................... Cat. #2960.21

US 115 V Power Cord ...................................................................... Cat. #5000.14

1.4 ACCESSORY INFORMATION

®

Dataview®software makes it possible to:

■Retrieve data from memory and plot graphs of the changes in insulation as a

function of the time over which the test voltage is applied, R(t).

■Print out protocols of personalized tests, depending on the user’s needs.

■

■Set up and control the instrument entirely by the USB serial port.



Check our Storefront at www.aemc.com/store for availability

Megohmmeter Model 5070 9

2. PRODUCT FEATURES

2.1 DESCRIPTION

The Model 5070 megohmmeter is a top-of-the-line measuring instrument,

portable, in a rugged housing with a graphic display. It is capable of operating

from internal battery or line power.



■Automatic detection and measurement of voltage/frequency/input current.

■Quantitative and qualitative insulation measurement.

• Measurement at 500/1000/2500/5000 V or other test voltage between

40 and 5100 V (adjustable voltage).

• Measurement in voltage step mode (the applied voltage increases in steps).

• Automatic calculation of DAR, PI, and DD (dielectric discharge index)

quality ratios.

• Automatic calculation of measurement result referred to a reference

temperature.

■Automatic capacitance measurement.

■Automatic measurement of residual current.

This megohmmeter helps ensure the safety of electrical installations and

equipment. The operation is controlled by a microprocessor for data acquisition,

processing, display of measurements, and storage of results.

Advantages:

■

■Automatic voltage measurement.

■Automatic detection of external AC or DC voltages on the terminals, before

or during insulation measurements, disabling or stopping the measurements

when measurement accuracy is no longer guaranteed.

■Threshold programming to trigger audible alarms.

■Timer for measurement time checks.

■Fuse protection of the instrument with detection and display of defective fuses.

■Operator safety by automatic discharge of residual high voltage on the

equipment tested.

■Automatic shutdown of the instrument to save battery power.

■Battery charge indication.

■Large backlit graphic display that is very easy to read.

■Memory (128 kB), real time clock, and serial interface.

■Control and programming of the instrument from a PC (using DataView software).

10 Megohmmeter Model 5070

2.1.1 Control Features

1. Safety terminals: +, G, and -.

2. Protective fuse access.

3. AC power plug (direct operation on AC and battery recharge).

4. Back-lit liquid crystal display.

5. Communication port: USB port (9600 baud).

6. Rotary selector switch with 8 positions:



 Instrument

OFF 󰀨

 

 

 

 

 Insulation measurement with selectable test voltage (from 40 to 5100

V: 10 V steps from 40 to 1000 V and 100 V steps from 1000 to 5000 V)

 Insulation measurement with voltage step function (up to 5 steps



 

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AEMC instruments Instrument de mesure

AEMC instruments

AEMC instruments AmpFlex Manuel utilisateur

AEMC instruments

AEMC instruments JM840A Manuel utilisateur

AEMC instruments

AEMC instruments 6536 Manuel utilisateur

AEMC instruments

AEMC instruments 1510 Manuel utilisateur

AEMC instruments

AEMC instruments MN185 Manuel utilisateur

AEMC instruments

AEMC instruments PowerPad IV 8345 Manuel utilisateur

AEMC instruments

AEMC instruments SR601 Manuel utilisateur

AEMC instruments

AEMC instruments JM852 Manuel utilisateur

AEMC instruments

AEMC instruments CA7027 Manuel utilisateur

AEMC instruments

AEMC instruments MN261 Manuel utilisateur

AEMC instruments

AEMC instruments CM605 Manuel utilisateur

AEMC instruments

AEMC instruments Simple Logger AmpFlex AL24-2500 Manuel utilisateur

AEMC instruments

AEMC instruments MN134 Manuel utilisateur

AEMC instruments

AEMC instruments 6292 Manuel utilisateur

AEMC instruments

AEMC instruments 6505 Manuel utilisateur

AEMC instruments

AEMC instruments SR701 Manuel utilisateur

AEMC instruments

AEMC instruments MN375 Manuel utilisateur

AEMC instruments

AEMC instruments CA811 Manuel utilisateur

AEMC instruments

AEMC instruments 5050 Manuel utilisateur

AEMC instruments

AEMC instruments 6505 Manuel utilisateur

AEMC instruments

AEMC instruments MN213 Manuel utilisateur

AEMC instruments

AEMC instruments SIMPLE LOGGER L100 Manuel utilisateur

AEMC instruments

AEMC instruments 6536 Manuel utilisateur

AEMC instruments

AEMC instruments 6240 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur