AEMC instruments SR601 Manuel utilisateur

AC Current Probe

Models SR601 and SR604

User Manual

DESCRIPTION: The SR601/SR604 (Cat. #2113.43/2113.44) are designed for use in industrial environments.

The ergonomic design allows them to easily attach to cables or small bus bars. The “circular” jaws guarantee

a very good accuracy and low phase shift. The probes have a measurement range up to 1000Arms

continuous and are compatible with any AC ammeter, multimeter, or other current measurement instrument

with an input impedance lower than 5Ω. To achieve the stated accuracy, use the SR601/SR604 with an

ammeter having an accuracy of 0.75% or better.

WARNING

The safety warnings are provided to ensure the safety of personnel and proper operation of the

instrument. Read the instruction completely.

• Use caution on any circuit: potentially high voltages and currents may be present and may pose a

shock hazard.

• Do not use the probe if damaged. Always connect the current probe to the measuring device before it

is connected around the conductor

• Do not use on non-insulated conductor with a potential to ground greater than 600V CAT III pollution

2. Use extreme caution when clamping around bare conductors or bus bars.

• Before each use, inspect the probe; look for cracks in housing or output cable insulation.

• Do not use clamp in wet environment or in locations that hazardous gases exist.

• Do not use the probe anywhere beyond the tactile barrier.

INTERNATIONAL ELECTRICAL SYMBOLS

This symbol signifies that the current probe is protected by double or reinforced insulation. Use only

factory specified replacement parts when servicing the instrument.

This symbol signifies CAUTION! and requests that the user refer to the user manual before using

the instrument.

This is a type A current sensor. This symbol signifies that application around and removal from

HAZARDOUS LIVE conductors is permitted.

DEFINITION OF MEASUREMENT CATEGORIES

CAT II: For measurements performed on circuits directly connected to the electrical distribution system.

Examples are measurements on household appliances or portable tools.

CAT III: For measurements performed in the building installation at the distribution level such as on

hardwired equipment in fixed installation and circuit breakers.

CAT IV: For measurements performed at the primary electrical supply (<1000V) such as on primary

overcurrent protection devices, ripple control units, or meters.

RECEIVING YOUR SHIPMENT

Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify your

distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the

carrier and notify your distributor at once, giving a detailed description of any damage.

ELECTRICAL SPECIFICATIONS

Current Range:

0.1 to 1000A AC, continuous cycle @ ≤1kHz

Transformation Ratio: 1000:1

Output Signal:

1mA AC/A AC (1A AC at 1000A)

Accuracy and Phase Shift*:

Primary current

0.1 to 10A

10A

50A

Accuracy %

≤3% + 0.1A

1.5%

Phase shift

N/A

3°

1.5°

Primary current

200A

1000A

1200A

Accuracy %

.75%

0.5%

Phase shift

0.75°

0.5°

(*Reference conditions: 23°C±3°K, 20 to 75% RH, 48 to

65 Hz, external magnetic field <40 A/m, no DC

component, no external current carrying conductor, test

sample centered.) Load impedance 5Ω.

Overload: 1200 A for 40mn on, 20mn off

Accuracy: Per IEC 185

Frequency Range: 30Hz to 5kHz; current derating

above 1 kHz using the formula:

SR601 SR604

Load Impedance: 5Ωmax

Working Voltage: 600V CAT III

Common Mode Voltage: 600V CAT III

Open Secondary Voltage:

< 25V by limiting circuit

Influence of Adjacent Conductor:

< 1mA/A AC

Influence of Conductor in Jaw Opening:

0.1% of reading

Influence of Frequency:

From 30 to 48Hz : < 1% of R

From 65 to 1000Hz : < 0.5% of R

From 1kHz to 5kHz : < 1% of R

MECHANICAL

SPECIFICATIONS

Operating Temperature:

14° to 122°F (-10° to 50°C)

Storage Temperature:

-4° to 158°F (-20° to 70°C)

Influence of Temperature:

< 0.1% per 10°K

Influence of Humidity:

From 10 to 90% : 0.1%

Jaw Opening:

2.25" (57mm) max.

Maximum Conductor Size:

2.05” (52mm)

Envelope Protection:

IP 40 (IEC 529)

Drop Test:

1m (IEC 68-2-32)

Mechanical Shock:

100g (IEC 68-2-27)

Vibration:

5 to 15Hz, 0.15mm (IEC 68-2-6)

15 to 25Hz, 1mm

25 to 55Hz, 0.25mm

Polycarbonate Material:

Handles: ABS Grey and

Lexan 500R, Red: UL94V0

Jaws: Lexan 500R, Red: UL94V0

Dimensions:

4.37 x 8.50 x 1.77" (111 x 216 x 45mm)

Weight:

1.21lbs. (550g)

Output:

SR601: Two standard safety banana

jacks (4mm)

SR604: 5ft. (1.5m) lead with safety

4mm banana plug

SAFETY SPECIFICATIONS

Electrical:

Double insulation or reinforced insulation between

the primary or secondary and the outer case of the

handle conforms to IEC 1010-2-032.

Common Mode Voltage:

600V Category III, Pollution Degree 2

Dielectric Strength:

5550V, 50/60Hz between primary, secondary

and the outer case of the handle

Electromagnetic Compatibility:

EN 50081-1 Class B

EN 50082-2 Electrostatic discharge

IEC 1000-4-2

Radiated field IEC 1000-4-3

Fast transients IEC 1000-4-4

Magnetic field at 50/60Hz IEC 1000-4-8

ORDERING INFORMATION

AC Current Probe SR601................Cat #2113.43

AC Current Probe SR604................Cat #2113.44

Accessories:

Lead, set of 2, 5ft Safety Leads

(1000V CAT IV) ..................................Cat#2152.24

Adapter BNC (Male) –Bannana (Female) (XM-BB)

(600V CAT III).....................................Cat#2118.46

Banana plug adapter

(to non-recessed plug) .....................Cat #1017.45

99-MAN 100132.v13 03/17

OPERATION

Please make sure that you have already read and fully understand the WARNING section on page 1.

Making Measurements with the AC Current Probe Models SR601/SR604

•Connect the black lead of the current probe to “common” and the red lead to the AC current input on

your DMM or other current measuring instrument. Select the appropriate current range (2A AC range).

Clamp the probe around the conductor to be tested with the arrow pointed toward the load. If the reading

is less than 200mA, select the lower range until you obtain the best resolution. Read the value display on

the DMM and multiply it by the probe ratio (1000/1). (If reading = 0.659A, the current flowing through the

probe is 0.659A x 1000 = 659A AC)

•For best accuracy, avoid if possible, the proximity of other conductors which may create noise.

Tips for Making Precise Measurements

•When using a current probe with a meter, it is important to select the range that provides the best

resolution. Failure to do this may result in measurement errors.

•Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air

gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for

power measurement.

MAINTENANCE

Warning:

•For maintenance use only original replacement parts.

•To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.

•To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents into

the probe

Cleaning:

To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all times.

Failure to do so may result in error in readings. To clean the probe jaws, use very fine sand paper (fine 600)

to avoid scratching the jaw, then gently clean with a soft oiled cloth.

REPAIR AND CALIBRATION

You must contact our Service Center for a Customer Service Authorization number (CSA#). This will ensure

that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA# on the

outside of the shipping container.

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive •Dover, NH 03820 USA

(800) 945-2362 (Ext. 360) • (603) 749-6434 (Ext. 360) • repair@aemc.com

(Or contact your authorized distributor)

NOTE: All customers must obtain a CSA# before returning any instrument.

TECHNICAL AND SALES ASSISTANCE

If you are experiencing any technical problems, or require any assistance with the proper use or application

of this instrument, please contact our technical hotline:

(800) 343-1391 • (508) 698-2115 • techsupport@aemc.com

LIMITED WARRANTY

The current probe is warranted to the owner for a period of two years

from the date of original purchase against defects in manufacture. This limited warranty is given by AEMC®

Instruments, not by the distributor from whom it was purchased. This warranty is void if the unit has been

tampered with, abused or if the defect is related to service not performed by AEMC®Instruments.

Full warranty coverage and product registration is available on our website at: www.aemc.com/warranty.html

Please print the online Warranty Coverage Information for your records.

Ce manuel convient aux modèles suivants

Autres manuels AEMC instruments Instrument de mesure

AEMC instruments

AEMC instruments MN185 Manuel utilisateur

AEMC instruments

AEMC instruments MN375 Manuel utilisateur

AEMC instruments

AEMC instruments 5050 Instructions d'utilisation et de sécurité

AEMC instruments

AEMC instruments Chauvin Arnoux 6412 Manuel utilisateur

AEMC instruments

AEMC instruments SR759 Manuel utilisateur

AEMC instruments

AEMC instruments CA7027 Manuel utilisateur

AEMC instruments

AEMC instruments 407 Manuel utilisateur

AEMC instruments

AEMC instruments MN290 Manuel utilisateur

AEMC instruments

AEMC instruments 1035 Manuel utilisateur

AEMC instruments

AEMC instruments MN125 Manuel utilisateur

AEMC instruments

AEMC instruments CA811 Manuel utilisateur

AEMC instruments

AEMC instruments 403 Manuel utilisateur

AEMC instruments

AEMC instruments MD305 Manuel utilisateur

AEMC instruments

AEMC instruments 1015 Manuel utilisateur

AEMC instruments

AEMC instruments MN02 Manuel utilisateur

AEMC instruments

AEMC instruments SL261 Manuel utilisateur

AEMC instruments

AEMC instruments JM852 Manuel utilisateur

AEMC instruments

AEMC instruments 6526 Manuel utilisateur

AEMC instruments

AEMC instruments AmpFlex 193-24-BK Manuel utilisateur

AEMC instruments

AEMC instruments 6550 Manuel utilisateur

AEMC instruments

AEMC instruments Simple Logger AmpFlex AL24-2500 Manuel utilisateur

AEMC instruments

AEMC instruments 6528 Manuel utilisateur

AEMC instruments

AEMC instruments AmpFlex Manuel utilisateur

AEMC instruments

AEMC instruments 6550 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur