Advantech TREK-722 Manuel utilisateur

User Manual

TREK-722/723

RISC All-In-One Mobile Data

Terminal

TREK-722/723 User Manual ii

The documentation and the software included with this product are copyrighted 2012

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice. No part of this manual may be reproduced, copied, translated or transmitted

in any form or by any means without the prior written permission of Advantech Co.,

Ltd. Information provided in this manual is intended to be accurate and reliable. How-

ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-

ments of the rights of third parties, which may result from its use.

Acknowledgements

TI and AM37x are trademarks of Texas Instruments..

Microsoft Windows is registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be

free from defects in materials and workmanship for two years from the date of pur-

chase.

This warranty does not apply to any products which have been repaired or altered by

persons other than repair personnel authorized by Advantech, or which have been

subject to misuse, abuse, accident or improper installation. Advantech assumes no

liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of

our customers never need to use our repair service. If an Advantech product is defec-

tive, it will be repaired or replaced at no charge during the warranty period. For out-

of-warranty repairs, you will be billed according to the cost of replacement materials,

service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advantech products used, other hardware and software used, etc.) Note

anything abnormal and list any onscreen messages you get when the problem

occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandize

authorization) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt)

in a shippable container. A product returned without proof of the purchase date

is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Part No. Edition 1

Printed in Taiwan May 2013

iii TREK-722/723 User Manual

Declaration of Conformity

This product has passed the CE test for environmental specifications. Test conditions

for passing included the equipment being operated within an industrial enclosure. In

order to protect the product from being damaged by ESD (Electrostatic Discharge)

and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-

sure products.

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference may

cause undesired operation.

RF Exposure Information

This device meets the government’s requirements for exposure to radio waves.

This device is designed and manufactured not to exceed the emission limits for expo-

sure to radio frequency (RF) energy set by the Federal Communications Commission

of the U.S. Government.

This device complies with FCC radiation exposure limits set forth for an uncon-

trolled environment. In order to avoid the possibility of exceeding the FCC radio

frequency exposure limits, human proximity to the antenna shall not be less

than 20cm (8 inches) during normal operation.

Changes or modifications not expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the equipment.

TREK-722/723 User Manual iv

Technical Support and Assistance

1. Visit the Advantech web site at http://support.advantech.com where you can find

the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

–Product name and serial number

–Description of your peripheral attachments

–Description of your software (operating system, version, application software,

etc.)

–A complete description of the problem

–The exact wording of any error messages

Warnings, Cautions and Notes

Document Feedback

To assist us in making improvements to this manual, we would welcome comments

and constructive criticism. Please send all such - in writing to: support@advan-

tech.com

Packing List

Before setting up the system, check that the items listed below are included and in

good condition. If any item does not accord with the table, please contact your dealer

immediately.

TREK-722/ TREK-723 Mobile Data Terminal

Warranty Card

"Drivers, utilities, and user manual" CD-ROM

End User License Agreement (WinCE), please download driver and relative

document from http://support.advantech.com

Power Cable

Warning! Warnings indicate conditions, which if not observed, can cause personal

injury!

Caution! Cautions are included to help you avoid damaging hardware or losing

data. e.g.

There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the

battery only with the same or equivalent type recommended by the man-

ufacturer. Discard used batteries according to the manufacturer's

instructions.

Note! Notes provide optional additional information.

v TREK-722/723 User Manual

Ordering Information

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equip-

ment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting

it fall may cause damage.

7. Do not leave this equipment in an environment unconditioned where the storage

temperature under -30° C (-22° F) or above 70° C (158° F), it may damage the

equipment.

8. Do not operate this equipment in an environment temperature may over 70° C

(158° F). The surface temperature of metal chassis may be scorch and hot.

9. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

10. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.The voltage and current rating of the cord should be greater

than the voltage and current rating marked on the product.

11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

The power cord or plug is damaged.

Liquid has penetrated into the equipment.

The equipment has been exposed to moisture.

The equipment does not work well, or you cannot get it to work according to

the user's manual.

The equipment has been dropped and damaged.

The equipment has obvious signs of breakage.

Part Number Description

TREK-722R-A0E TREK-722 barebone

TREK-722R-CBCEA0E TREK-722R-A0E w/ GPS, CDMA, BT, CE

TREK-722R-GBCEA0E TREK-722R-A0E w/ GPS, GPRS, BT, CE

TREK-722R-HBCEA0E TREK-722R-A0E w/ GPS, HSPA, BT, CE

TREK-723R-A0E TREK-723 barebone

TREK-723R-CBCEA0E TREK-723R-A0E w/ GPS, CDMA, BT, CE

TREK-723R-GBCEA0E TREK-723R-A0E w/ GPS, GPRS, BT, CE

TREK-723R-HBCEA0E TREK-723R-A0E w/ GPS, HSPA, BT, CE

TREK-722/723 User Manual vi

15. This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

16. CAUTION: Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections while the

power is on. Sensitive electronic components can be damaged by sudden

power surges.

17. CAUTION: Always ground yourself to remove any static charge before touching

the motherboard, backplane, or add-on cards. Modern electronic devices are

very sensitive to static electric charges. As a safety precaution, use a grounding

wrist strap at all times. Place all electronic components on a static-dissipative

surface or in a static-shielded bag when they are not in the chassis.

18. CAUTION: Any unverified component could cause unexpected damage. To

ensure the correct installation, please always use the components (ex. screws)

provided with the accessory box.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from

damage.

To avoid electrical shock, always disconnect the power from your system chas-

sis before you work on it. Don't touch any components on the main board or

other cards while the system is on.

Disconnect power before making any configuration changes. The sudden rush

of power as you connect a jumper or install a card may damage sensitive elec-

tronic components.

Warning! 1. Input voltage rated: 6 ~36 Vdc (12/24V power).

2. Transport: carry the unit with both hands and handle with care.

3. Maintenance: to properly maintain and clean the surfaces, use only

approved products or clean with a dry applicator.

4. SD/SIM card: Turn off the power before inserting or removing the

storage cards.

vii TREK-722/723 User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ...............................................................................................2

1.2 General Specifications ..............................................................................2

1.3 Dimensions ...............................................................................................4

Figure 1.1 TREK-722 dimensions................................................4

Figure 1.2 TREK-723 dimensions................................................4

Chapter 2 System Setup.......................................5

2.1 A Quick Tour of the TREK-722/723 Mobile Data Terminal .......................6

Figure 2.1 Front view of TREK-722/723......................................6

Figure 2.2 Rear view of TREK-722/723.......................................6

Figure 2.3 Bottom view of TREK-722/723...................................6

2.2 Installation Procedures..............................................................................7

2.2.1 Connecting the Power Cord..........................................................7

Figure 2.4 Power connector photo...............................................7

Table 2.1: Pin Definition of Power Cord ......................................7

2.3 WinCE Satrtup Procedure.........................................................................7

Chapter 3 Hardware & Peripheral Installation....9

3.1 Installing the Storage Device and SIM Card ...........................................10

3.2 Installing Optional Accessories...............................................................10

3.3 Installing Standard Wireless Options......................................................11

3.3.1 WWAN (Internal Antenna) ..........................................................11

3.3.2 Bluetooth (Internal Antenna).......................................................11

3.3.3 GPS (Internal Antenna)...............................................................12

3.4 Installing External Wireless Antenna Options .........................................12

3.4.1 HSPA and GPRS (External Antenna).........................................12

3.4.2 CDMA (External Antenna) ..........................................................13

3.4.3 GPS (External Antenna) .............................................................14

Chapter 4 Pin Assignments ...............................15

4.1 Rear Side Connectors.............................................................................16

4.2 Extended IO............................................................................................17

Table 4.1: Extended IO..............................................................17

4.3 HDC Cable Connectors (Optional) (Advantech P/N: 1700020042) ........18

Chapter 5 Software Functionality......................23

5.1 Introduction .............................................................................................24

Figure 5.1 Windows® Embedded CE 6.0 on the TREK72x plat-

form ..........................................................................24

5.2 Windows CE Startup Procedure .............................................................24

5.3 Upgrade Procedure.................................................................................25

5.3.1 Prepare SD card for bootloader..................................................25

Figure 5.2 Storage format tool...................................................25

5.3.2 Upgrade image: ..........................................................................25

Figure 5.3 Boot files...................................................................25

Figure 5.4 Upgrade finish ..........................................................26

TREK-722/723 User Manual viii

Figure 5.5 Format disk............................................................... 26

5.4 Utilities .................................................................................................... 27

5.4.1 Test Utility................................................................................... 27

5.4.2 Test Procedure........................................................................... 27

Figure 5.6 Test Utility................................................................. 27

5.4.3 Startup execution........................................................................ 28

5.4.4 Platform Setting.......................................................................... 28

Figure 5.7 General information.................................................. 29

Figure 5.8 Audio........................................................................ 29

5.5 Network................................................................................................... 30

5.5.1 Setup for HSPA and GPRS........................................................ 30

Figure 5.9 3G via Ethernet ........................................................ 30

Figure 5.10RF module manager................................................. 31

Figure 5.11ISP modern setting................................................... 31

5.5.2 Example for Verizon CDMA Setup ............................................. 32

5.6 Touch Calibration.................................................................................... 34

Figure 5.12Touch panel calibration............................................ 34

5.7 Application Program Development ......................................................... 34

5.7.1 PC System requirements............................................................ 34

5.7.2 Building Windows CE program................................................... 35

Figure 5.13Flow-chart of Building Windows® Embedded CE 6.0

runtime ..................................................................... 35

5.7.3 How to install SDK...................................................................... 35

5.7.4 Running IMC SDK CE Demo Test.............................................. 39

5.7.5 Running your application programs............................................ 44

5.7.6 SUSI library for application program........................................... 44

5.8 Windows® Embedded CE 6.0 Component List...................................... 44

Chapter 1

1General Information

This chapter gives background

information on the TREK-722/723

Mobile Data Terminal.

Sections include:

Introduction

General Specifications

Dimensions

TREK-722/723 User Manual 2

1.1 Introduction

TREK-722/723 is a RISC platform with 5"/7" display all-in-one Mobile Data Terminal

(MDT). The radio frequency options and programmable function keys make TREK-

722/723 suitable for local fleet management. It is designed with vehicle power com-

pliant to ISO7637-2 & SAE J1113 ensuring the system is stable in dirty car power

system. With Suspend/Wakeup feature, TREK-722/723 supports 24/7 monitoring

mechanism by periodical, digital input & WWAN wakeup.

1.2 General Specifications

Key features

5" & 7" LCD (800 x 480) with resistive touchscreen

24/7 monitoring & reporting

Cortex-A8 TI AM3703 800 MHz

WinCE6.0 & optional Android 2.3.4

Built-in CAN bus with J1939 protocol

Built-in GPS with AGPS feature, BT, CDMA/GPRS/HSPA+

Operating temperature: -20 ~ 60° C (5") & -30 ~ 70° C (7")

Storage temperature: -30 ~ 80° C

Specifications

Dimensions: 165 x 115 x 43 mm (TREK-722) / 213 x 145 x 43 mm (TREK-723)

Weight: 650 gram (TREK-722) / 850 gram (TREK-723)

Power feature:

–Input Voltage: 6~36Vdc

–Supports power on delay (default 2 seconds)

–Supports power off delay (default 5 seconds)

–Supports hardware power off delay (default 30 seconds)

–Supports WWAN wake up

SoC: TI ARM Cortex-A8 AM3703 800 MHz

OS: WinCE 6.0 R3 core version / Android 2.3.4 Gingerbread

RAM: On board 256MB Mobile LPDDR

Storage:

–On board NAND type 2GB for boot loader, OS & customer's APs

–1 x push-push type SD slot

LCD: 5" industrial grade wide screen TFT LCD, 800 x 480 resolution (TREK-

722)/ 7" industrial grade wide screen TFT LCD, 800 x 480 resolution (TREK-

723)

Touch Screen: 4-wire resistive with flat panel design

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Advantech Terminal tactile

Advantech

Advantech WebOP-3000 Series Manuel utilisateur

Advantech

Advantech POC-WP21 Series Manuel utilisateur

Advantech

Advantech UPOS-211 Manuel utilisateur

Advantech

Advantech PPC-V106 Manuel utilisateur

Advantech

Advantech ADAM-3600-C2G Series Manuel utilisateur

Advantech

Advantech POC-S155 Manuel utilisateur

Advantech

Advantech MARS-1030F Manuel utilisateur

Advantech

Advantech TREK-773 Manuel utilisateur

Advantech

Advantech ADAM-3968M/PMA Manuel d'installation et d'exploitation

Advantech

Advantech TREK-725 Manuel utilisateur

Advantech

Advantech USC-360 Manuel d'installation et d'exploitation

Advantech

Advantech EH-7104G Manuel utilisateur

Advantech

Advantech POC-W211 Manuel utilisateur

Advantech

Advantech POC-S196 Manuel utilisateur

Advantech

Advantech UPOS-3150 Manuel utilisateur

Advantech

Advantech TPC-1240 Manuel utilisateur

Advantech

Advantech TREK-723 Manuel utilisateur

Advantech

Advantech HIT-W101C Manuel d'instructions

Advantech

Advantech HIT-W18 Series Manuel utilisateur

Advantech

Advantech POC-S175 Manuel utilisateur

Advantech

Advantech POC-S199 Series Manuel utilisateur

Advantech

Advantech POC-176 Manuel utilisateur

Advantech

Advantech POC-S198 Manuel utilisateur

Advantech

Advantech PIT-1701 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur