Advantech POC127 Manuel utilisateur

User Manual

POC-127

Intel® Pineview-M N450 CPU

based Point of Care Terminal

with 12.1” LED panel

POC-127 User Manual ii

The Instructions for the User

The document combines text and illustrations, providing a comprehensive overview

of the system. The information is presented as sequential steps of action, allowing

the user to learn directly how to use the device.

The text provides explanations and instructs the user step by- step in the practical

use of the product, with short, clear instructions in easy-to-follow sequence.

Definitions

Part No. 2008012700 Edition 1

Printed in Taiwan November 2011

Warning! A WARNING statement provides important information about a poten-

tially hazardous situation which, if not avoided, could result in death or

serious injury.

Caution! A CAUTION statement provides important information about a poten-

tially hazardous situation which, if not avoided, may result in minor or

moderate injury to the user or patient or in damage to the equipment or

other property.

Note! A NOTE provides additional information intended to avoid inconve-

niences during operation.

iii POC-127 User Manual

Safety Instructions

Strictly follow these Instructions for Use, please read these safety instructions care-

fully.

Remind to keep this User's Manual for later reference, and any use of the product

requires full understanding and strict observation of all portions of these instructions.

Observe all WARNINGS and CAUTIONS as rendered throughout this manual and on

labels on the equipment.

Repair of the device may also only be carried out by trained service personnel.

Advantech recommends that a service contract be obtained with Advantech Service

and that all repairs also be carried out by them. Otherwise the correct functioning of

the device may be compromised.

If one of the following situations arises, get the equipment checked by service per-

sonnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to the

user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do

not use liquid or spray detergents for cleaning and keep this equipment away from

humidity.

Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage. For plug-in equipment, the power outlet socket must be located

near the equipment and must be easily accessible.

Make sure the voltage of the power source is correct before connecting the equip-

ment to the power outlet. Position the power cord so that people cannot step on it. Do

Warning! Because of the danger of electric shock, never remove the cover of a

device while it is in operation or connected to a power outlet.

Caution! To avoid short-circuiting and otherwise damaging the device, do not

allow fluids to come in contact with the device. If fluids are accidentally

spilled on the equipment, remove the affected unit from service as soon

as possible and contact the service personnel to verify that patient

safety is not compromised.

Caution! To prevent overheating, do not cover the openings and place the device

in direct sunlight or near radiant heaters.

POC-127 User Manual iv

not place anything over the power cord. If the equipment is not used for a long time,

disconnect it from the power source to avoid damage by transient over voltage.

If your computer is losing dramatic time or the BIOS configuration reset to default, the

battery has no power.

Improper installation of VESA mounting can result in serious personal injury! VESA

mount installation should be operated by professional technician, please contact the

service technician or your retail if you need this service. The detail operating proce-

dure specified on Appendix A.

CLASSIFICATION:

Supply Class I adapter

No applied part

IPX1

Continuous Operation

Not AP or APG category

Maintenance: to properly maintain and clean the surfaces, use only the approved

products or clean with a dry applicator.

Make sure the user not to contact SIP/SOPs and the patient at the same time.

When networking with electrical devices, the operator is responsible for ensuring that

the resulting system meets the requirements set forth by the following standards:

Caution! Do not leave this equipment in an uncontrolled environment where the

storage temperature is below -20° C (-4°F) or above 60° C (140°F). This

may damage the equipment.

Caution! Do not replace battery yourself. Please contact a qualified technician or

your retail.

The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace

only with same or equivalent type recommended by the manufacture.

Discard used batteries according to the manufacturer’s instructions.

Warning! This device is not suitable for use in the presence of flammable anes-

thetic mixture with air, oxygen, nitrous oxide, or for life support system.

Caution! When servicing the device, always use replacement parts that are quali-

fied to Advantech standards. Advantech Medical cannot warrant or

endorse the safe performance of third-party replacement parts for use

with our medical device.

v POC-127 User Manual

®C EN 60601-1 (IEC 60601-1)

Medical electrical equipment

Part 1: General requirements for safety

®C EN 60601-1-1 (IEC 60601-1-1)

Medical electrical equipment

Part 1-1: General requirements for safety

Collateral standard: Safety requirements for

Medical electrical systems

®C EN 60601-1-2 (IEC 60601-1-2)

Medical electrical equipment

Part 1-2: General requirements for safety

Collateral standard: Electromagnetic compatibility; Requirements and tests

Accessory equipment connected to the analog and digital interfaces must be in com-

pliance with the respective nationally harmonized IEC standards (i.e. IEC 60950 for

data processing equipment, IEC 60065 for video equipment, IEC 61010-1 for labora-

tory equipment, and IEC 60601-1 for medical equipment.) Furthermore all configura-

tions shall comply with the system standard IEC 60601-1-1. Everybody who connects

additional equipment to the signal input part or signal output part configures a medi-

cal system, and is therefore, responsible that the system complies with the require-

ments of the system standard IEC 60601-1-1. The unit is for exclusive

interconnection with IEC 60601-1 certified equipment in the patient environment and

IEC 60XXX certified equipment outside of the patient environment. If in doubt, con-

sult the technical services department or your local representative.

Grounding reliability can only be achieved when the equipment is connected to an

equivalent receptacle marked “Hospital Only” or “Hospital Grade”.

Use a power cord that matches the voltage of the power outlet, which has been

approved and complies with the safety standard of your particular country.

Warning! If fix the equipment to mobile equipment, re-evaluation of the product in

according to IEC/EN 60601-1 will be required.

POC-127 User Manual vi

Explanation of Graphical Symbols

Disposing of your old product

Within the European Union

Note! Environmental protection

Follow national requirements to dispose of unit.

IEC 60878 and ISO 3864-B.3.6 : Warning: dangerous voltage.

ISO 7000-0434 : Caution, consult ACCOMPANYING DOCUMENTS.

ISO 7000-1641 : Follow operating instructions or Consult instructions for

use.

IEC 60417 -5009 : SANDY-BY.

IEC 60417-5031 : Direct current.

IEC 60417-5021 : Equipotentiality.

EU-wide legislation, as implemented in each Member State, requires

that waste electrical and electronic products carrying the mark (left) must

be disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow

the guidance of your local authority, or ask the shop where you pur-

chased the product, or if applicable, follow any agreements made

between yourself.

The mark on electrical and electronic products only applies to the current

European Union Member States.

vii POC-127 User Manual

Guidance and manufacturer’s declaration - electromagnetic emissions

The model POC-127 is intended for use in the electromagnetic environment specified below.

The customer or the user of the model POC-127 should assure that it is used in such an

environment.

Emissions test Compliance Electromagnetic environment - guidance

RF emissions

CISPR 11 Group 1 The model POC-127 uses RF energy only for

its internal function. Therefore, its RF emis-

sions are very low and are not likely to cause

any interference in nearby electronic equip-

ment.

RF emissions

CISPR 11 Class B The model POC-127 is suitable for use in all

establishments, including domestic establish-

ments and those directly connected to the pub-

lic low-voltage power supply network that

supplies buildings used for domestic pur-

poses.

Harmonic emissions

IEC 61000-3-2 Class A

Voltage fluctuations/

flicker emissions

IEC 61000-3-3

Not applicable

Recommended separation distances between

portable and mobile RF communications equipment and the model POC-127

The model POC-127 is intended for use in an electromagnetic environment in which radiated

RF disturbances are controlled. The customer or the user of the model POC-127 can help

prevent electromagnetic interference by maintaining a minimum distance between portable

and mobile RF communications equipment (transmitters) and the model POC-127 as recom-

mended below, according to the maximum output power of the communications equipment.

Rated

maximum

outputpower

transmitter

Separation distance according to frequency of transmitter

150 kHz to 80 MHz

d = 1,2 80 MHz to 800 MHz

d = 1,2 800 MHz to 2,5 GHz

d = 2,3

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters rated at a maximum output power not listed above, the recommended sepa-

ration distance d in metres (m) can be estimated using the equation applicable to the fre-

quency of the transmitter, where P is the maximum output power rating of the transmitter in

watts (W) according to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range

applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is

affected by absorption and reflection from structures, objects and people.

POC-127 User Manual viii

Information on potential electromagnetic interference and advice on

how to avoid or minimize such interference (IEC/EN 60601-1-2:2007)

Guidance and manufacturer’s declaration - electromagnetic immunity

The model POC-127 is intended for use in the electromagnetic environment specified below.

The customer or the user of the model POC-127 should assure that it is used in such an

environment.

Immunity test IEC 60601

test level Compli-

ance level Electromagnetic environment - guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3 Vrms

150 kHz to

80 MHz

3 V/m

80 MHz to

2,5 GHz

3 Vrms

3 V/m

Portable and mobile RF communications equip-

ment should be used no closer to any part of the

model POC-127, including cables, than the rec-

ommended separation distance calculated from

the equation applicable to the frequency of the

transmitter.

Recommended separation distance

d = 1,2

d = 1,2 80 MHz to 800 MHz

d = 2,3 800 MHz to 2,5 GHz

where P is the maximum output power rating of

the transmitter in watts (W) according to the

transmitter manufacturer and d is the recom-

mended separation distance in metres (m).

Field strengths from fixed RF transmitters, as

determined by an electromagnetic site survey, a

should be less than the compliance level in each

frequency range. b

Interference may occur in the vicinity of equip-

ment marked with the following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is

affected by absorption and reflection from structures, objects and people.

aField strengths from fixed transmitters, such as base stations for radio (cellular/cordless)

telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV

broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic

environment due to fixed RF transmitters, an electromagnetic site survey should be consid-

ered. If the measured field strength in the location in which the model POC-127 is used

exceeds the applicable RF compliance level above, the model POC-127 should be observed

to verify normal operation. If abnormal performance is observed, additional measures may

be necessary, such as reorienting or relocating the model POC-127.

bOver the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

ix POC-127 User Manual

FCC Class B

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential environment. This equipment

generates uses and can radiate radio frequency energy. If not installed and used in

accordance with this user's manual, it may cause harmful interference to radio com-

munications.

Note that even when this equipment is installed and used in accordance with this

user's manual, there is still no guarantee that interference will not occur. If this equip-

ment is believed to be causing harmful interference to radio or television reception,

this can be determined by turning the equipment on and off. If interference is occur-

ring, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

List of Accessories

Before installing your Point of Care Terminal, ensure that the following materials have

been received:

POC-127 series Point of Care Terminal

Accessories for POC-127

–CD-ROM disc-"Drivers, User's manual and Utilities"

–Mounting kits and packet of screws.

–VESA mounting note x1

–China RoHs note x1

Warning! Any changes or modifications made to the equipment which are not

expressly approved by the relevant standards authority could void your

authority to operate the equipment.

Warning! No user serviceable parts inside, refer servicing to qualified personnel.

Only the accessories indicated on the list of accessories above have

been tested and approved to be used with the device. Accordingly it is

strongly recommended that only these accessories be used in conjunc-

tion with the specific device. Otherwise the correct functioning of the

device may be compromised.

POC-127 User Manual x

Additional Information and Assistance

Contact your distributor, sales representative, or Advantech's customer service cen-

ter for technical support if you need additional assistance. Please have the following

information ready before you call:

Product name and serial number

Description of your peripheral attachments

Description of your software (operating system, version, application software,

etc.)

A complete description of the problem

The exact wording of any error messages

This equipment is a source of electromagnetic waves. Before use please, make

sure that there are not EMI sensitive devices in its surrounding which may mal-

function therefore.

Environmental protection

Follow national requirements to dispose of unit.

Contact Information

Manufacturer

Advantech Co., Ltd.

No.1, Alley 20, Lane 26, Reuiguang Road Neihu District, Taipei,

Taiwan 114, R.O.C.

TEL: (02)27927818

Distributed in European by

Advantech Europe GmbH Kolberger Strasse 7

D-40599 Dusseldorf, Germany

Tel: 49-211-97477350

Fax: 49-211-97477300

Visit the Advantech websites at www.advantech.com or www.advantech.com.tw if

you need more information.

Autres manuels pour POC127

Table des matières

Autres manuels Advantech Terminal tactile

Advantech

Advantech PPC-V106 Manuel utilisateur

Advantech

Advantech HIT-W101C Manuel d'instructions

Advantech

Advantech POC-S196 Manuel utilisateur

Advantech

Advantech POC-176 Manuel utilisateur

Advantech

Advantech HIT-W18 Series Manuel utilisateur

Advantech

Advantech TREK-722 Manuel utilisateur

Advantech

Advantech UbiQ-480 Manuel utilisateur

Advantech

Advantech TPC-1240 Manuel utilisateur

Advantech

Advantech UPOS-3150 Manuel utilisateur

Advantech

Advantech ProFlat IDP31-190-P35HIB1E Manuel utilisateur

Advantech

Advantech WP-75**-**10/40 Manuel utilisateur

Advantech

Advantech MT-100 Manuel utilisateur

Advantech

Advantech PWS 472 Manuel utilisateur

Advantech

Advantech ADAM-3952/PMA Manuel utilisateur

Advantech

Advantech POS-560-B1 Manuel utilisateur

Advantech

Advantech POC-S155 Manuel utilisateur

Advantech

Advantech PPC-V106 Manuel utilisateur

Advantech

Advantech POC-S199 Series Manuel utilisateur

Advantech

Advantech POC-155 Manuel utilisateur

Advantech

Advantech POC-S175 Manuel utilisateur

Advantech

Advantech TREK-723 Manuel utilisateur

Advantech

Advantech ADAM-3600-C2G Series Manuel utilisateur

Advantech

Advantech POC-W152 Manuel utilisateur

Advantech

Advantech UPOS-211 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur