Zortrax Z-NYLON Instructions de montage

Tips for Printing with Z-NYLON

SOURCE:

https://support.zortrax.com/z-nylon-tips/

Table Of Content

Storage & Preparation 3

Hardware Requirements 4

Model Preparation Tips 5

Printing Process Requirements 6

Storage & Preparation

Z-NYLON is highly hydroscopic and shouldn’t be stored without protection in humid

environments for a long time. Unused spools have to be stored in an airtight container

with a moisture absorber. Otherwise, the filament will absorb moisture from air which can

cause problems such as stringing or low surface quality of printed parts. Also, the color

of the filament can fade or become dull.

To remove moisture from the filament, perform a drying procedure at 90 °C [194 °F] for

2 hours.

Hardware Requirements

To create the best printing environment for Z-NYLON, it is best to equip your printer with

a separate hotend and a perforated plate that will be dedicated only for printing with this

material. These parts should be new and not used with other materials.

Also, avoid using adhesive substances with the new perforated plate.

Model Preparation Tips

As all nylon-based materials, Z-NYLON is highly prone to warping. That’s why, while

preparing your model in Z-SUITE, go to Advanced section in the Print settings step and

set the Fan speed to 0%.

If you’re preparing several small models for printing, make sure to separate them in the

workspace so that each item has its own raft structure. This way, a smaller printing area

can reduce the risk of warping.

Printing Process Requirements

While printing with Z-NYLON, it is recommended to provide proper conditions in the print

room. First of all, make sure that there are no draughts in your work area. Strong

airflows cause warping and may damage your print. Also, avoid printing in humid

conditions. Due to its high shrinkage, Z-NYLON is not recommended for printing large

geometric models with steep slopes in the Z axis. In general, models with walls that are

perpendicular to the platform will be less prone to warping. Still, it is advisable to add

support structures to all angles and overhanging parts of your model.

To reduce shrinkage, it is advisable to create a printing chamber with the use of Side

Covers and a HEPA Cover. These accessories have been designed to support the

printing process with materials of a high shrinkage rate.

Lastly, remove any residues of material extruded during the pre-print calibration. This will

facilitate adhesion of raft and the whole model to the perforated plate.

Powered by TCPDF (www.tcpdf.org)

Table des matières

Autres manuels zortrax Imprimante 3D

zortrax

zortrax X/Y Manuel utilisateur

zortrax

zortrax M300 Manuel utilisateur

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Z-Axis Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax DSS Manuel utilisateur

zortrax

zortrax M200 Manuel

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation

zortrax

zortrax M200 Plus Mode d’emploi

zortrax

zortrax Z-PETG Manuel utilisateur

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Plus Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax M300 Instructions d'utilisation

zortrax

zortrax M300 Feuille d'instructions

zortrax

zortrax M Series Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax Z-PLA Pro Instructions de montage

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur