Zortrax Z-Axis Manuel d'utilisation et d'entretien

Z-Axis Coupler Replacement

SOURCE:

https://support.zortrax.com/z-axis-coupler-replacement/

page 1 / 25

Table Of Content

Unplugging the Power Cable 4

Changing the Printer's Position 5

Unscrewing the Bottom Plate, part 1 6

Turning the Printer 7

Unscrewing the Bottom Plate, part 2 8

Separating the Bottom Plate 9

Providing Better Access to the Z-Axis Coupler 10

Unplugging the Z-Axis Motor Cable 11

Loosening the Z-Axis Coupler Screws 12

Unscrewing the Z-Axis Motor 13

Z-Axis Coupler Removal 14

Z-Axis Coupler Assembly 15

Z-Axis Motor Assembly 16

Tightening the Z-Axis Coupler Screws 17

Plugging the Z-Axis Motor Cable 18

Rearranging the Cables 19

Bottom Plate Installation 20

Securing the Bottom Plate, part 1 21

Turning the Printer 22

Securing the Bottom Plate, part 2 23

Changing the Printer's Position 24

Plugging the Power Cable 25

page 2 / 25

The Z-axis coupler is responsible for the platform’s movement along the Z axis.

Therefore, if the platform does not move at all or it moves with difficulties and

makes unusual noises, the Z-axis couple needs to be replaced. Before replacing

the coupler, make sure that the screws on the coupler are properly tightened.

More details can be found in the manual.

If the screws cannot be fully tightened, follow the steps from this manual to replace the Z-

axis coupler.

The following manual shows the M200 repair work. For the M300, these procedures are

the same.

page 3 / 25

Unplugging the Power Cable

Turn off the printer and unplug the power cable. Wait a few minutes for all the capacitors

to discharge.

page 4 / 25

Changing the Printer's Position

Grab the printer’s housing and change the printer’s position so that you can easily

access the bottom plate.

page 5 / 25

Unscrewing the Bottom Plate, part 1

Unscrew the screws that secure the bottom plate on one side of the housing. Use a

2.5mm Allen key.

page 6 / 25

Turning the Printer

Turn the printer over.

page 7 / 25

Unscrewing the Bottom Plate, part 2

Unscrew the screws that secure the bottom plate on the other side of the housing. Use

the same key.

page 8 / 25

Separating the Bottom Plate

Separate the bottom plate from the printer and unplug the bottom fan cable from the

motherboard.

page 9 / 25

Providing Better Access to the Z-Axis Coupler

Unfasten the two extruder cable straps and unplug the cable from the motherboard.

Next, unfasten the third strap. Place the extruder cable between the power supply unit

and the housing. Finally, grab the cables next to the motherboard and fasten the strap.

This step is not necessary to follow, however it is recommended so as to avoid the risk

of damaging the cables and to get better access to the Z-Axis coupler.

page 10 / 25

Autres manuels pour Z-Axis

1

Table des matières

Autres manuels zortrax Imprimante 3D

zortrax

zortrax M300 Instructions d'utilisation

zortrax

zortrax M200 Plus Manuel utilisateur

zortrax

zortrax Apoller Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Curing Station Manuel utilisateur

zortrax

zortrax M200 Manuel d'utilisation

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M300 Plus Manuel d'utilisation

zortrax

zortrax Z-PLA Pro Instructions de montage

zortrax

zortrax DSS Manuel utilisateur

zortrax

zortrax Z-NYLON Instructions de montage

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax HEPA Cover Instructions d'utilisation

zortrax

zortrax M200 Plus Feuille d'instructions

zortrax

zortrax M200 Plus Guide d'installation

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax M Series Manuel d'utilisation et d'entretien

zortrax

zortrax Inkspire Manuel utilisateur

zortrax

zortrax M200 Plus Mode d’emploi

zortrax

zortrax M200 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur