Zortrax Endstop Sleeve Manuel utilisateur

Endstop Sleeve Installation

SOURCE:

https://support.zortrax.com/endstop-sleeve-installation/

page 1 / 12

Table Of Content

Unplugging the Power Cable 4

Unplugging the Extruder Cable 5

Loosening the Screws on the Axis Block 6

Unscrewing the Axis Block Cover 7

Endstop Sleeve Installation 8

Securing the Axis Block Cover 9

Tightening the Screws on the Axis Block 10

Plugging the Extruder Cable 11

Plugging the Power Cable 12

page 2 / 12

The endstop sleeve is responsible for pressing the lever of the endstop once the

extruder reaches the end of the axis. This action immediately informs the printer

that the extruder should stop moving and not crash into the housing. Therefore, if

the extruder keeps hitting a corner of the housing, and an error message appears

on the display (Endstops error #034), check if the endstop sleeves are installed on

each axis block. The sleeves should be attached to the inner side of the axis

block. This manual gives instructions on the endstop sleeve installation. There is

an endstop sleeve model available for download at the Zortrax Library.

The following manual shows the M200 repair work. For the M300, M200 Plus and M300

Plus, these procedures are the same.

page 3 / 12

Unplugging the Power Cable

Turn off the printer and unplug the power cable.

page 4 / 12

Unplugging the Extruder Cable

Unplug the extruder cable.

page 5 / 12

Loosening the Screws on the Axis Block

Move the extruder toward the axis block on which you will install the endstop sleeve.

Loosen the two screws placed at the bottom of the opposite axis block using a 1.5mm

Allen key.

page 6 / 12

Unscrewing the Axis Block Cover

Move the extruder toward the opposite axis block. Unscrew the two front screws on the

axis block on which you will install the endstop sleeve. Use a 2mm Allen key. Slightly

move the axis block cover away from the block to gain easier access to the place where

the endstop sleeve should be screwed in.

page 7 / 12

Endstop Sleeve Installation

Turn the axis block and screw in the endstop sleeve using a 2mm Allen key. Turn the

axis block to its previous position.

page 8 / 12

Securing the Axis Block Cover

Push the axis block cover closer to the block and secure it with the two screws.

page 9 / 12

Tightening the Screws on the Axis Block

Move the extruder toward the opposite axis block. Tighten the two screws placed at the

bottom of the axis block using a 1.5mm Allen key.

page 10 / 12

Table des matières

Autres manuels zortrax Imprimante 3D

zortrax

zortrax M200 Plus Guide d'installation

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax HEPA Cover Instructions d'utilisation

zortrax

zortrax M300 Manuel utilisateur

zortrax

zortrax M200 Plus Manuel utilisateur

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax X/Y Manuel utilisateur

zortrax

zortrax M200 Manuel

zortrax

zortrax M300 Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax M300 Feuille d'instructions

zortrax

zortrax M300 Manuel d'utilisation

zortrax

zortrax M200 Manuel d'utilisation

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax Z-PETG Manuel utilisateur

zortrax

zortrax M200 Manuel utilisateur

zortrax

zortrax FEP Film Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Plus Mode d’emploi

zortrax

zortrax M300 Plus Manuel d'utilisation

zortrax

zortrax M200 Plus Manuel d'utilisation et d'entretien

zortrax

zortrax M200 Manuel d'utilisation et d'entretien

zortrax

zortrax Z-Axis Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur