Westermo Lynx Plus Manuel utilisateur

©Westermo Teleindustri AB

www.westermo.com

User Guide

6643-2210

Industrial Ethernet

10-port Switch

Lynx+

26643-2210

License Information

This device contains public available software which is under the GPL license.

For more information see legal.pdf included with all firmware releases.

This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit. http://www.openssl.org

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document.Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

6643-2210

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that you under-

stand it fully. Check that your application does not exceed the safe operating specifications for

this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to

service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be possible to dis-

connect manually from the power supply. Ensure compliance to national installation regulations.

This unit uses convection cooling. To avoid obstructing the airflow around the unit, follow the

spacing recommendations (see Cooling section)..

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from power supply.

Warning! Do not open connected unit. Hazardous voltage may occur within this unit when

connected to power supply.

Class 1 Laser Product

Do not look directly into fibre optical fibre port or any connected fibre although this unit is

designed to meet the Class 1 Laser regulations.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil the warranty

obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling above the specification may cause damage to

internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not waterproof.

Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical part may

be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office

or Westermo Tech support.

Fibre connectors are supplied with plugs to avoid contamination inside the optical port.

As long as no optical fibre is mounted on the connector, e.g. for storage, service or transportation,

should the plug be applied.

WARNING – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR DIVISION 2

WARNING – DO NOT OPEN WHEN ENERGIZED

WARNING – DO NOT DISCONNECT EQUIPMENT UNLESS AREA IS KNOWN TO BE

NONHAZARDOUS

SPECIAL CONDITION OF USE:

This equipment shall be installed in compliance with the enclosure, mounting, spacing and segregation

requirements of the ultimate application, including a tool removable cover.

46643-2210

Note. Fibre Optic Handling

Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If the

fibre will be disconnected from the unit the protective hood on the transmitter/receiver

must be connected.The protective hood must be kept on during transportation.

The fibre optic cable must also be handled the same way.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should be cleaned by the use of

forced nitrogen and some kind of cleaning stick.

Recommended cleaning fluids:

Methyl-, ethyl-, isopropyl- or isobutyl-alcohol, Hexane, Naphtha.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-4, Emission industrial environments

EN 55022 +A1, Emission IT equipment

EN 55024, Immunity IT equipment

FCC part 15 Class A

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Safety EN 60950-1, IT equipment

FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment.This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

6643-2210

Declaration of Conformity

Westermo Teleindustri AB

Declaration of conformity

.nr

Postadress/Postal address

Tel. Telefax Postgiro Bankgiro Corp. identity number

Registered o

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstun

Sweden Int+46 16428000 Int+46 16428001

The manufacturer

Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Type of product Model Art no

Ethernet switch L+210-series switches 3643-0100

is in conformity with the following EC directive(s).

No Short name

2004/108/EC Electromagnetic Compatibility (EMC)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 50121-4 Railway applications – Electromagnetic compatibility

– Emission and immunity of the signalling and

telecommunications apparatus

2006

EN 55022 Information technology equipment - Emission 2006

+A1:2007

EN 55024 Information technology equipment - Immunity 1998

+A1:2001

+A2:2003

EN 61000-6-1 Electromagnetic compatibility – Immunity for

residential environments

2007

EN 61000-6-2 Electromagnetic compatibility – Immunity for

industrial environments

2005

EN 61000-6-4 Electromagnetic compatibility – Emission for

industrial environments

2007

The last two digits of the year in which the CE marking was affixed: 10

Pierre Öberg

Technical Manager

3 May 2010

66643-2210

Type tests and environmental conditions

Environmental phenomena Basic standard Description Test levels

ESD EN 61000-4-2 Enclosure Contact: ±6 kV

Air: ±8 kV

Fast transients EN 61000-4-4 Power port ±2 kV

Signal ports ±2 kV

Earth port ±1 kV

Surge EN 61000-4-5 Power port L-E: ±0.5 kV, 12 Ω, 9 μF

L-L: ±0.5 kV, 2 Ω, 18 μF

L-E: ±2 kV, 42 Ω, 0.5 μF

L-L: ±2 kV, 42 Ω, 0.5 μF

L-E: ±2 kV, 12 Ω, 9 μF

L-L: ±1 kV, 12 Ω, 9 μF

Signal ports L-E: ±1 kV, 2 Ω

L-E: ±2 kV, 42Ω, 0.5 μF

Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 50 Hz

Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m

Radiated RF immunity EN 61000-4-3 Enclosure 10 V/m @ (80 – 800) MHz

20 V/m @ (800 – 1000) MHz

10 V/m @ (1400 – 2100) MHz

5 V/m @ (2100 – 2500) MHz

1 V/m @ (2500 – 2700) MHz

1 kHz sine, 80% AM

Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz

Signal ports 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz

Earth port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz

Radiated RF emission EN 55022 Enclosure Class A

FCC Part 15 Class A

Conducted RF emission EN 55022 Power port Class B

Signal ports Class B

Dielectric strength EN 60950-1 Power port to all

other ports

1.5 kVrms, 50 Hz, 1 min

Signal ports to all

other ports

1.5 kVrms, 50 Hz, 1 min

Environmental

Temperature Operating –40 to +70 °C

Storage and transport –50 to +85 °C

Humidity Operating 5 to 95 % relative humidity

Storage and transport 5 to 95 % relative humidity

Altitude Operating 2 000 m / 70 kPa

Service life Operating 10 year

Vibration IEC 60068-2-6

(sine)

Operating 3 – 13.2 Hz: 1mm

13.2 – 100 Hz: 0.7 g

5.5 – 30 Hz: 1.5 g

30 – 50 Hz: 0.42 mm

50 – 500 Hz: 4.2 g*

IEC 60068-64

(random)

Operating 5 – 20 Hz: 2 m2/s3

20 – 2000 Hz: –3 dB/oct

Shock IEC 60068-2-27 Operating 30 g, 11 ms

100 g, 6 ms*

Bump IEC 60068-2-27 Operating 10 g, 11 ms

Packaging

Enclosure EN 60950-1 Zinc Fire enclosure

Dimension W x H x D

With connectors

52.5 x 100 x 101 mm

52.5 x 119 x 101 mm

Weight 0.7 kg

Degree of protection EN 60529 Enclosure IP 40

Cooling Convection

* Might require Ethernet cables to be fastened close to the unit.

6643-2210

Description

Lynx+ is an Industrial switch made for harsh enviroments. The switch can be used in

ether 100 Mbit or Gigabit networks due to our multi-rate SFP solution. Lynx+ can also

be used together with our previous Lynx-series of switches. Our unique FRNT

(Fast Recovery of Network Topology) technology is the fastest protocol on the market

to re-configure a network in the event of any link or hardware failure. That is why Lynx+

is used in safety critical applications such as tunnels, traffic signal control and railway

systems.

Installations in harsh environments and places with heavy electrical interference require

the use of a reliable media. Lynx+ provides a number of solutions using fibre optic trans-

ceivers. Multi- or singlemode transceivers can be used to build point-to-point or redun-

dant ring networks with ranges up to 120 km between each switch. Our BIDI transceiver,

which transmits and receives data on a single fibre can be used in applications where the

number of fibre cores are limited.

Real-time properties are implemented in the switch in order to achieve determinism

for real time critical applications. Lynx+ supports QoS (Quality of Service) with four

priority queues and strict priority scheduling as well as HoL (Head of Line Blocking

Prevention). All to assure that the data network is deterministic.

86643-2210

Interface specifications

Power

Operating voltage Rated: 24 to 48 VDC

Operating: 19 to 60 VDC

Rated current 240 mA @ 24 VDC

120 mA @ 48 VDC

Rated frequency DC

Inrush current, I2t 6.4 · 10-3 A2s @ 48 VDC

Startup current* 2 * Rated current

Polarity Reverse polarity protected

Redundant power input Yes

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2(AWG 24 – 12)

Shielded cable Not required

* External supply current capability for proper start-up

Ethernet TX

Electrical specification IEEE std 802.3. 2005 Edition

Data rate 10 Mbit/s, 100 Mbit/s, manual or auto

Duplex Full or half, manual or auto

Circuit type TNV-1

Transmission range Up to 150 m with CAT5e cable or better

Isolation to All other

Connection RJ-45, auto MDI/MDI-X

Shielded cable Not required, except when installed in Railway applications as

signalling and telecommunications apparatus and located close

to rails.*

Conductive housing Yes

Number of ports 8

Ethernet SFP pluggable connections (FX or TX)

Electrical specification IEEE std 802.3. 2005 Edition

Data rate 100 Mbit/s or 1000 Mbit/s transceivers supported

Duplex Full or Auto, depending on transceiver

Transmission range Depending on tranceiver

Connection SFP slot holding fibre transceiver or copper transceiver

Number of ports 1 or 2

* To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m

boundary or the cable is longer than 30 m and inside 10 m boundary to the rails and connected to this port.

6643-2210

I/O / Relay output

Maximum voltage/current 60 VDC / 80 mA

Contact resistance Max 30 Ω

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2(AWG 24 – 12)

I/O / Digital input

Maximum voltage/load current 60 VDC / 2 mA

Voltage levels Logic one: >12V

Logic zero: <1V

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2(AWG 24 – 12)

Console

Electrical specification TTL-level

Data rate 115.2 kbit/s

Data format 8 data bits, no parity, 1 stop bit, no flow control

Circuit type SELV

Isolation to All other

Connection 2.5 mm jack, use only Westermo cable 1211-2027

SFP Transceivers

Supported transceivers

See SFP Transceivers User Guide 6100-0000 for supported SFP transceivers.

Note: The unit supports Westermo labelled transceivers only.

Deviations

With copper transceiver 1100-0148 the specified operating temperature on Lynx+

is 0 to +50ºC.

FRNT reconfiguration times can not be guaranteed with copper transceivers.

10 6643-2210

Location of interface ports and LED’s

Ethernet connection TX (8 ports)

Position Signale Direction Description

No.1 TD+ In/Out Transmitted/Received data

No. 2 TD– In/Out Transmitted/Received data

No. 3 RD+ In/Out Transmitted/Received data

No. 4 – Not Connected

No. 5 – Not Connected

No. 6 RD– In/Out Transmitted/Received data

No. 7 – Not Connected

No. 8 – Not Connected

Shield Connected to PE

LED Indicators (for details see page 12)

Power connection (for details see page 11)

SFP transceivers

(for details see page 9)

I/O connection (for details see page 11) Console port

(for details see page 9)

Cable 1211-2027

Connection to console port

The console port can be used to connect to the CLI

(Command Line Interface).

The following steps needs to be taken

1. Connect the serial diagnostic cable to the console port

(use only Westermo cable 1211-2027).

2. Connect cable to your computer (USB port, if drivers are needed they can be downloaded

from our Web page).

3. Use a terminal emulator and connect with correct speed and format (115200, 8N1)

to the assigned port.

For more information about the CLI, see the WeOS management guide.

Bottom view

Table des matières

Autres manuels Westermo Routeur réseau

Westermo

Westermo MDI-118 Series Manuel utilisateur

Westermo

Westermo MR-210 Manuel utilisateur

Westermo

Westermo Ibex-RT-630 Series Manuel utilisateur

Westermo

Westermo MRD-315 Manuel utilisateur

Westermo

Westermo MRD-405 Manuel utilisateur

Westermo

Westermo MRD-415 Manuel utilisateur

Westermo

Westermo Lynx DSS L208-F2G-S2-EX Manuel utilisateur

Westermo

Westermo DR-250 Manuel utilisateur

Westermo

Westermo Lynx L106-F2G Manuel utilisateur

Westermo

Westermo Viper 408 Manuel utilisateur

Westermo

Westermo DDW-02-B1 Manuel utilisateur

Westermo

Westermo BRD-355A Manuel utilisateur

Westermo

Westermo Viper 108 Manuel utilisateur

Westermo

Westermo LRW-112 Series Manuel utilisateur

Westermo

Westermo RedFox Rail Manuel utilisateur

Westermo

Westermo BRD-355 Manuel utilisateur

Westermo

Westermo SDW-500 Manuel utilisateur

Westermo

Westermo SDW-541-F1G-T4G Manuel utilisateur

Westermo

Westermo Ibex-330 Series Manuel utilisateur

Westermo

Westermo MRD-315 Manuel utilisateur

Westermo

Westermo RedFox Manuel utilisateur

Westermo

Westermo Falcon Series Manuel utilisateur

Westermo

Westermo Lynx DSS Manuel utilisateur

Westermo

Westermo RT-370 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité