Westermo BRD-355 Manuel utilisateur

www.westermo.com

BRD-355

Industrial ADSL/VDSL Router

6623-2232

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind, either express or implied, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy and reliability or contents of this document. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

www.westermo.com

6623-2232

Safety information

Before installation:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

The unit must be installed by a service person and connected to a protective

earthing contact. Disconnect all telecommunication network connectors and

cable distribution system connectors before disconnecting the protective earthing

contacts.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be

possible to disconnect manually from the power supply. Ensure compliance to

national installation regulations.

This unit uses convection cooling. To avoid obstructing the airflow around the unit,

follow the spacing recommendations (see Cooling section).

This unit uses negative earth, therefore the 0 V and protective earth must be

connected to ensure robust functionality.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from power supply.

Warning! Do not open connected unit. Hazardous voltage may occur within this

unit when connected to power supply.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil

the warranty obligations.

This unit must not be operating with removed covers or lids. Do not attempt to

disassemble the unit. There are no user serviceable parts inside. Do not drop, knock

or shake the unit, rough handling above the specification may cause damage to internal

circuit boards. Do not use harsh chemicals, cleaning solvents or strong detergents

to clean the unit. Do not paint the unit. Paint can clog the unit and prevent proper

operation. Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit

is not waterproof. Keep the unit within the specified humidity levels. Do not use or

store the unit in dusty, dirty areas, connectors as well as other mechanical parts may be

damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

6623-2232

Product disposal

This symbol means that the product shall not be treated as

unsorted municipal waste when disposing of it. It needs to

be handed over to an applicable collection point for recy-

cling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

6623-2232

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

Safety EN 60950-1, IT equipment

Simplified EU declaration of conformity

Hereby, Westermo declares that the equipment is in compliance with applicable EU

directives. The full EU declaration of conformity and other detailed information are

available at the respective product page at www.westermo.com..

6623-2232

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)

Enclosure air ± 8 kV (crit A)

Radiated RF immunity IEC 61000-4-3 Enclosure 20 V/m (crit A)

(80 – 2700 MHz)

Fast transient EN 61000-4-4 DC power ports ± 2 kV (crit A)

Ethernet ports ± 2 kV (crit A)

Serial port ± 2 kV (crit B)

xDSL ports ± 2 kV (crit B)

Surge EN 61000-4-5 DC power ports ± 2 kV (crit A), 42 Ω

± 500 V (crit A), 12 Ω

Ethernet ports ± 2 kV (crit A), (shielded cable)

xDSL ports ± 2 kV (crit B)

RF conducted EN 61000-4-6 DC power ports 10 V/m, (crit A), (0.15 – 80 MHz)

Ethernet ports 3 V/m, (crit A), (0.15 – 80 MHz)

10 V/m, (crit B), (0.15 – 80 MHz)

xDSL ports 3 V/m (crit A), (0.15 – 80 MHz)

10 V/m (crit B), (0.15 – 80 MHz)

Radiated emission CISPR 16-2-3 Enclosure EN 61000-6-3

Conducted emission CISPR 16-2-1 DC power ports

EN 61000-6-3

CISPR 32 Ethernet ports

xDSL port

Temperature EN 60068-2-1

EN 60068-2-2

Operating –25 to +70°C (–13 to +158°F)

Storage & Transport –40 to +85°C (–40 to +185°F)

Humidity EN 60068-2-30 Operating 0 to 90% relative humidity non

condensing.

Storage & Transport 0 to 90% relative humidity non

condensing.

Altitude Operating 2000 m / 70 kPa

Service life Operating 10 year

Dimension W x H x D 53 x 103 x 97 mm

(2.08 x 4.05 x 3.81 in)

Weight 0.40 kg

Degree of protection IEC 529 Enclosure IP 40

Cooling Convection

Mounting Horizontal on 35 mm DIN-rail

6623-2232

Description

Remote access removes boundaries, eliminates the need for time consuming site visits

and provides a network infrastructure suitable for today's “always-on” society. The BRD-

355 is an industrially designed xDSL (ADSL/VDSL2) broadband router built to cope with

harsh environments and the characteristics of industrial applications. The unit supports a

wide range of xDSL-standards and has support for long lines.

Most devices today comes equipped with an Ethernet port for communications,

therefore the BRD-355 has a built-in two port Ethernet switch. For legacy connectivity

the unit also features one RS-232-port to provide multiple connection possibilities for

both new and legacy replacement installations. Designed to be installed on a DIN-rail

all connectors and LEDs have been positioned in the front of the unit, facing the user

for easy access and fast status feedback. With wide power input range, the unit can be

powered from 10 to 60 VDC and has low power consumption.

The cyber security features of the BRD-355 prevent unauthorized access and secure the

communication for Internet-enabled applications. The easy to use firewall filters incoming

traffic, allowing only approved packets to pass through. To inter-connect units with each

other securely over the Internet multiple VPN technologies are supported, including

IPsec and OpenVPN.

Upgrading legacy solutions to become IP-enabled can prove both costly and tedious

therefore the BRD-355 includes a wide feature set for various legacy applications

including both modem replacement methods as well as serial to Ethernet conversion.

If there are applications that require extra attention Westermo's extensive experience

from over 35 years within industrial data communications and over 5 years of industrial

xDSL expertise will be available to assist you.

6623-2232

Interface specifications

Power

Rated voltage 12 – 48 VDC

Operating voltage 10 – 60 VDC

Operational current (max) 450 mA @ 12 VDC

Rated current (max) 1000 mA @ 12 VDC

Rated frequency DC

RS-232

Electrical specification EIA RS-232

Data rate 300 bit/s – 115.2 kbit/s

Data format 7 or 8 data bits, Odd, even or none parity, 1 or 2 stop bits

Protocol Transparent, optimised by packing algorithm

Circuit type SELV

Transmission range 15 m / 49 ft

Connection 9 pin D-sub female

Shielded cable Not required

Conductive housing Ye s

Number of ports 1

Ethernet TX

Electrical specification IEEE std 802.3. 2005 Edition

Data rate 10 Mbit/s, 100 Mbit/s, manual or auto

Duplex Full or half, manual or auto

Circuit type SELV

Transmission range 100 m / 328 ft

Isolation to All other

Connection RJ-45 auto MDI/MDIX

Shielded cable Not required

Conductive housing Ye s

Number of ports 2

6623-2232

DSL

Protocol LLC/VC-MUX encap Ethernet, PPPoA, PPPoE, IPoA

Connection 1 x RJ-11

Version Common name Standard Downlink Uplink

ADSL ADSL ANSI T1.413 8 Mbit/s 1.0 Mbit/s

ADSL (G.dmt) ITU G.992.1 8 Mbit/s 1.0 Mbit/s

ADSL (G.lite) ITU G.992.2 1.5 Mbit/s 0.5 Mbit/s

ADSL over POTS ITU G.992.1 Annex A 12 Mbit/s 1.3 Mbit/s

ADSL over ISDN ITU G.992.1 Annex B 12 Mbit/s 1.8 Mbit/s

ADSL2 RE-ADSL ITU G.992.3 Annex L1/L2 5 Mbit/s 0.8 Mbit/s

ADSL2 ITU G.992.3 12 Mbit/s 1.3 Mbit/s

ADSL2 Annex J ITU G.992.3 Annex J 12 Mbit/s 3.5 Mbit/s

ADSL2+ ADSL2+ ITU G.992.5 24 Mbit/s 1.4 Mbit/s

ADSL2+ Annex M ITU G.992.5 Annex M 24 Mbit/s 3.3 Mbit/s

VDSL2 VDSL2 ITU G.993.2* 100 Mbit/s** 100 Mbit/s**

VDSL2 Vectoring ITU G.993.5 G.Vector 100 Mbit/s** 100 Mbit/s**

* Supports profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a.

** Maximum sustained routing performance over time is around 35 Mbit/s.

Table des matières

Autres manuels Westermo Routeur réseau

Westermo

Westermo MRD-350 Manuel utilisateur

Westermo

Westermo DR-260 Manuel utilisateur

Westermo

Westermo Lynx DSS L208-F2G-S2-EX Manuel utilisateur

Westermo

Westermo SDW-550 E-mark Manuel utilisateur

Westermo

Westermo MRD-310 Manuel utilisateur

Westermo

Westermo DR-250 Manuel utilisateur

Westermo

Westermo Ibex-330 Series Manuel utilisateur

Westermo

Westermo MR-210 Manuel utilisateur

Westermo

Westermo RT-370 Manuel utilisateur

Westermo

Westermo SDW-541-F1G-T4G Manuel utilisateur

Westermo

Westermo MDI-118 Series Manuel utilisateur

Westermo

Westermo Viper 008 Manuel utilisateur

Westermo

Westermo Viper-12 Series Manuel utilisateur

Westermo

Westermo Viper 008 Manuel utilisateur

Westermo

Westermo Lynx Plus Manuel utilisateur

Westermo

Westermo BRD-355A Manuel utilisateur

Westermo

Westermo MRD-405 Manuel utilisateur

Westermo

Westermo Lynx 5600 Series Manuel utilisateur

Westermo

Westermo SDI-550 Manuel utilisateur

Westermo

Westermo Lynx DSS Manuel utilisateur

Westermo

Westermo Falcon Series Manuel utilisateur

Westermo

Westermo ADSL-350 Manuel utilisateur

Westermo

Westermo MRD-315 Manuel utilisateur

Westermo

Westermo LRW-112 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité