Korenix JetNet 5710G Series Manuel utilisateur

Korenix JetNet 5710G Series

Industrial 8-Port PoE + 2 Gigabit TX

Managed Ethernet Switch

User Manual

Ver. 02, NOV, 2010

Firmware version: 0.1.37

www.korenix.com

Korenix JetNet 5710G Series

Industrial 8 Port PoE + 2 Gigabit TX Managed Ethernet

Switch

User’s Manual

Reproduction in any form or by any means without permission is prohibited.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his expense.

The user is cautioned that changes and modifications made to the equipment

without approval of the manufacturer could void the user's authority to operate

this equipment.

Index

1 Introduction.............................................................................................1

1.1 Overview........................................................................................1

1.2 Major Features...............................................................................4

1.3 Package List ..................................................................................5

2 Hardware Installation..............................................................................6

2.1 Hardware Introduction....................................................................7

2.2 Wiring the Power Inputs...............................................................10

2.3 Wiring Earth Ground ....................................................................11

2.4 Wall-Mounting Installation............................................................12

3 Preparation for Management ...............................................................13

3.1 Preparation for Serial Console.....................................................13

3.2 Preparation for Web Interface......................................................14

3.3 Preparation for Telnet Console.....................................................17

4 Feature Configuration ..........................................................................20

4.1 Command Line Interface Introduction..........................................21

4.2 Basic Setting................................................................................27

4.3 Port Configuration........................................................................46

4.4 Power over Ethernet ....................................................................54

4.5 Network Redundancy...................................................................64

4.6 VLAN............................................................................................75

4.7 Traffic Prioritization.......................................................................85

4.8 Multicast Filtering.........................................................................91

4.9 SNMP...........................................................................................96

4.10 Security......................................................................................100

4.11 Warning......................................................................................108

4.12 Monitor and Diag........................................................................119

4.13 Device Front Panel ....................................................................127

4.14 Save to Flash.............................................................................128

4.15 Logout........................................................................................129

5 Appendix .............................................................................................130

5.1 Product Specifications................................................................130

5.2 Korenix Private MIB ...................................................................135

5.3 Revision History.........................................................................137

5.4 About Korenix ............................................................................138

1 Introduction

Welcome to Korenix JetNet 5710G Series Industrial 8-Port PoE + 2G

Managed Ethernet Switch User Manual. Following topics are covered in

this chapter:

1.1 Overview

1.2 Major Features

1.3 Package Checklist

1.1 Overview

The JetNet 5710G series are Managed Industrial Power over Ethernet

Switches, equipped with 8 ports 10/100 TX with 30watts PoE injector and 2

10/100/1000 TX ports for uplink. The 8 ports PSE injector, compliant with IEEE

802.3af/ 802.3at and forced powering feature to supports non-standard

Powered Device (PD). The Gigabit Ethernet ports can be formed as a

redundant ring network or connect with higher level back-bond switch with

MSRTM technologies and provides faster recovery time-less than 5 ms.

Various Network Control and Security Features

The JetNet 5710G provides various network control and security features. The

Network control feature allows user to optimize the industrial network

environment. The supported features include VLAN, IGMP Snooping, Quality

of Service (QoS), Link Aggregation Control Protocol (LACP), Rate Control. The

security also helps users to avoid hacker’s attack. The features included are

DHCP client, DHCP server with IP and MAC binding, 802.1X Access Control,

SSH for Telnet security, IPAccess table and port security.

.Power budget limitation with priority control

The JetNet 5710G provides budget and priority control to ensure the total

power consumption will not over the power budget of power supply user

installed. It also provides budget control function to limit the output power if PD

device is not claimed right consumption numbers. This features allows user to

protect high priority PD device will not be shut down which caused by power

supply over loading protection.

Driving the High Power PoE market - Security, WiMAX

Since the ratification of the Power over Ethernet standard in 2003, the Power

over Ethernet technology becomes a trend; more devices adopt PD

technology to obtain power through Ethernet cable. However, the IEEE

802.3af 15.4 w powers can’t satisfy the applications, such like WiMAX, IP DOM

Camera, which require from 15.4w up to 30 watts power. The JetNet 5710G is

equipped with the new PSE solution compliant with both IEEE 802.3af and

IEEE 802.3at 1-event plus 30w high power LLDP protocol standards. It

supports 8 PoE ports in End-span wiring architecture with 30w powering ability

to drive the motor of outdoor PZT IP cameras with direction control for

cross –street monitoring or WiMAX systems for internet access at train stations,

airports or Hot-spots.

Comprehensive Redundant Solutions – Multiple Super Ring (MSRTM)

The JetNet 5710G supports new generation ring technology - MSRTM (Multiple

Super Ring); the next new generation of RSRTM (Rapid Super Ring) technology.

This new technologies is prefect for different network redundancy applications

and structures. With the MSRTM technology, a node can be configured to

multiple rings with the failover time in as little as 5ms and zero-second of

restore time. In addition, users can extend the ring topology by adding

hundreds of JetNet series to meet the network needs without compromising

the speed of the network. The MSRTM also facilitates the JetNet series to

connect with coe management switch vi standard rapid spanning tree protocol

or through multiple paths or nodes to increase the reliability by RDHTM (Rapid

Dual Homing )(RDHTM )technology. By integrating MSRTM and Link

Aggregation Control Protocol (LACP) the JetNet series can enhance the link

availability and increase to overall link capacity. Two or more Fast Ethernet

connections are bundled in order to increase the bandwidth and to create a

resilient and redundant link

Rapid Super ring (RSRTM) Technology

Rapid Super Ring is the 2nd generation of Korenix Ring Redundancy

technology. The recovery time is greatly improved from 30ms to few ms for

both copper and fiber ring. The Ring master can be auto-selected by RSR

engine. The 1st ring port of the R.M. is the primary path while the 2nd ring port

of the R.M. is the block path. Once the primary path fails, the 2nd path will be

recovered within few ms. Besides, the restore time is also shortened to zero in

the R.M. auto-selection mode.

Seamless Ring Port Restoration TM

Seamless restoration is a new Korenix patented technology which can restore

a failed ring without causing any loop problem, topology change, packet loss

and restoration time. This makes a perfect restoration that will not result in any

loop, technology change and restoration time (restoration time = 0 second).

Rapid Dual Homing (RDHTM) Technology

Rapid Dual Homing is also the important feature of Korenix new generation

Ring technology. It supports ring coupling with other vendors and with easy

configuration and multiple redundancies, the failover time is much faster and

the restore time is zero ms. Uplinks can be auto detected and gathered into

groups. In each group, uplinks are sorted into primary, secondary and

standbys by their link speed. The uplink with the highest speed is more likely to

be active path for data transmission. Link aggregation is also integrated into

RDHTM. An uplink connection can be a single link or several links aggregated

as a trunk, which provides better redundancy and link capacity.

TrunkRingTM

TrunkRing is a new feature in MSR which merges the two technologies of RSR

and link aggregation. It takes advantages of aggregation to enhance the link

redundancy, while increase the link speed. The ring will open only if all the

aggregated links are broken. Link aggregation can be achieved by either,

static trunk or LACP. Not all the link sections in a TrunkRing need to be the

same. Ring links can be either symmetric or asymmetric. Some are a single

path, and the others are aggregated by links where the number of links in a

trunk group can be different. Users can enhance the link redundancy at

different locations in accordance to the need.And the link with less speed is

more likely to be used as the backup path for restoring the network to full play

capacity.

Link Aggregation Control Protocol

Link Aggregation Control Protocol allows you grouping multiple Ethernet ports

in parallel to increase the link bandwidth. The aggregated ports can be viewed

as one physical port, so that the bandwidth is higher than just one single

Ethernet port. The member ports of the same trunk group can balance the

loading and backup with each other. The LACP feature is usually used when

you need higher bandwidth for the backbone network. This is a cost-effective

way for you to transfer much more data.

Multi Powering Mechanism- User Manual, Forced and IEEE 802.3at LLDP

Power over Ethernet

Some of Legacy PD devices also feature user defined manual mode and

forced powering mode to support non-standard PD devices without the PoE

signature resistor for some WiMax systems, which are non-compliant with

IEEE 802.3at LLDP Power over Ethernet.

For the new PoE standard – IEEE 802.3at, JetNet 5710G implements Link

Layer Discovery Protocol (LLDP) into the system for allowing power budget

negotiation between PD devices while providing smart power budget control

behavior.

Magical Topology Discovery & Management – JetView Pro

JetNet 5710G supports topology discovery or LLDP (IEEE 802.1AB Link Layer

Discovery Protocol) function that can help users to discover multi-vendor’s

network devices on the same segment by an NMS system which supports

LLDP function. With LLDP function, NMS can easily maintain the topology map,

display port ID, port description, system description, VLAN ID and so on. Once

a link failure happens, the topology changed events are updated to the NMS to

help users easily maintain the network system. Like as the JetView Pro, not

only supports topology discovery, it also delivers group IP assignment,

firmware upgrade, configuration files backup/ restore ,SNMP MIB Broswer

/compile, MSRTM group management and also allows user to exports topology

map to drawing file-JPEG, BMP, PNG or PDF for other application.

1.2 Major Features

Korenix JetNet 5710G supports following features:

8 10/100 Base TX and 2 Gigabit ports

8 –port IEE 802.3af 15.4w /802.3at 30w Power over Ethernet

32Gbps switch Fabric, 8K MAC address

Korenix patented MSR pattern aggregates up to 4 x 100M Rings plus 1

Gigabit Ring

LACP/VLAN/ GVRP/ QoS/ IGMP Snooping/Rate Control/ Online Multi-Port

Mirroring/DHCP /IEEE 802.1AB LLDP

Advanced Security system by Port Security, Access IP list, SSH and

HTTPS Login

Event Notification through E-mail, SNMP trap and SysLog

Cisco-Like CLI, Web, SNMP/RMON for network Management

Redundant DC Power Inputs and Relay Output

AC 1.5KV Hi-Pot Protection for power port to case.

Industrial Heat dispersing design,-40~70°C wide operating temperature

Note: The detail spec is listed in Appendix 5.1.

1.3 Package List

Unpack the box and you will find:

JetNet 5710G

Quick Installation Guide

CD User Manual

Wall /Panel Mounting kits with screw x 1 set

2 Hardware Installation

This chapter includes hardware introduction, installation and

configuration information.

Following topics are covered in this chapter:

2.1 Hardware Introduction

Dimension

Panel Layout

Bottom View

2.2 Wiring Power Inputs

2.3 Wiring Digital Input

2.4 Wiring Relay Output

2.5 Wiring Ethernet Ports

2.6 Wiring Combo Ports

2.7 Wiring RS-232 console cable

2.8 DIN-Rail Mounting Installation

2.9 Wall-Mounting Installation

Autres manuels pour JetNet 5710G Series

Table des matières

Autres manuels Korenix Routeur réseau

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

Korenix

Korenix JetBox 9430 Manuel utilisateur

Korenix

Korenix JetNet 7852G-4XG Series Manuel utilisateur

Korenix

Korenix JetBox9500 series Manuel utilisateur

Korenix

Korenix JetNet 5310G Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

Korenix

Korenix JetNet 6059G Manuel utilisateur

Korenix

Korenix JetNet 3705 Manuel utilisateur

Korenix

Korenix JetNet 5010G Series Manuel utilisateur

Korenix

Korenix JetNet 5010G Series Manuel utilisateur

Korenix

Korenix JetNet 3008 v3 Manuel utilisateur

Korenix

Korenix JetBox 5630 Manuel utilisateur

Korenix

Korenix JetNet 3006 Series Manuel utilisateur

Korenix

Korenix JetNet 5010G Series Manuel utilisateur

Korenix

Korenix JetNet 7850G-2XG Manuel utilisateur

Korenix

Korenix 5-port 10/100 Manuel utilisateur

Korenix

Korenix JetNet 5008G-P Series Manuel utilisateur

Korenix

Korenix JetNet 6710G Manuel utilisateur

Korenix

Korenix JetNet 5228G Series Manuel utilisateur

Korenix

Korenix JetNet 6059G Manuel utilisateur

Korenix

Korenix JetNet 5628G Series Manuel utilisateur

Korenix

Korenix JetNet 5628G Series Manuel utilisateur

Korenix

Korenix JetBox 9462-w Manuel utilisateur

Korenix

Korenix JetWave 4020 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur