Westermo RedFox Manuel utilisateur

Ethernet switch and router

approved for railway usage

www.westermo.com

©Westermo Teleindustri AB

User Guide

6641-2222

RedFox

RAIL

6641-2222

License Information

This device contains public available software which is under the GPL lincense.

For more information see legal.pdf included with all firmware releases.

This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit, http://www.openssl.org

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

Software tools

Related software tools are available in the folder software tools under

technical support on the Westermo website.

6641-2222

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only. The power supply wiring must be sufficiently

fused, and if necessary it must be possible to disconnect manually from all power

supply. Ensure compliance to national installation regulations. This unit relies on

convection heating. Make sure that it is installed so that the ambient temperature

is within the specified temperature range, e.g. by avoiding obstruction of the

airflow around the unit. Also check chapter CEN/TS 45545-2 mounting notes.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from all power supply.

WARNING

Do not open connected unit. Hazardous voltage may occur within this unit when

connected to power supply.

Before powering-up, a protective earthing conductor must be connected to the

protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

Note that this unit can be connected to two different power sources.

When this unit is operated at an ambient temperature above +60°C (+140°F), the

External Surface of Equipment may exceed Touch Temperature Limit according to

EN/IEC/UL 60950-1. To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication line cord.

6641-2222

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill

the warranty obligations:

…Do not attempt to dissassemble the unit. There are not any user serviceable

parts inside.

…Do not drop, knock or shake the unit. Rough handling above the specification

may cause damage to internal circuit boards.

…Do not use harsh chemicals, cleaning solvents or strong detergents to clean the

unit.

…Do not expose the unit to any kind of liquid (water, beverages, paint etc),

unless all connectors are connected or fitted with protective caps (delivered

with the unit), tightened to the specified torque. Connected cables must have

the appropriate ingress protection code.

…Do not use or store the unit in dusty or dirty areas, unless all connectors and

the ventilation membrane are sufficiently protected.

…Do not cover or bring mechanical force to the ventilation membrane on the

back of the unit.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

6641-2222

Type Approval / Compliance

EMC EN 50121-3-2, Railway applications – EMC: Rolling stock – Apparatus

Railway applications, Approval/Compliance – EN 50155

Railway applications – Electronic equipment used on rolling stock

Safety EN 60950-1, IT equipment

Agency approvals and standards compliance

6641-2222

Declaration of Conformity

Westermo Teleindustri AB

Declaration of conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer

Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model Art no

EN 50155 Backbone Routing Switch RFR-12-FB 3641-1630

is in conformity with the following EC directive(s).

No Short name

2004/108/EC Electromagnetic Compatibility (EMC)

2006/95/EC Low voltage (LVD)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and

electronic equipment (RoHS)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 50121-3-2 Railway applications - Electromagnetic compatibility -- Rolling

stock - Apparatus

2006

EN 60950-1 Information technology equipment - Safety -- General

requirements

2006

+A11:2009

+A1:2010

+A12:2011

The last two digits of the year in which the CE marking was affixed: 12

Pierre Öberg

Technical Manager

21st December 2012

6641-2222

Type tests and environmental conditions

Electromagnetic Compatibility

Phenomena Standard Description Test Levels

ESD EN 61000-4-2 Enclosure contact

discharge immunity

±6 kV

Enclosure air discharge

immunity

±8 kV

RF field AM modulated EN 61000-4-3 Enclosure RF immunity 20 V/m

80 – 2700 MHz

Fast transients EN 61000-4-4 Signal port immunity ±2 kV

Power port immunity ±2 kV

Surges EN 61000-4-5 Power port immunity ±2 kV (L-E)

±1 kV (L-L)

EN 50155:2001 Power port immunity ±8.4 kV (L-E)

±8.4 kV (L-L)

Conducted RF emision EN 61000-4-6 Signal port immunity 10 V/m

0.15 – 80 MHz

Power port immunity 10 V/m

0.15 – 80 MHz

Power frequency magnetic field EN 61000-4-8 Enclosure immunity 300 A/m

0, 16.7, 50 Hz

Pulsed magnetic field EN 61000-4-9 Enclosure immunity 300 A/m

Voltage interruption EN 50155 Residual voltage 0% 10 ms

Supply overvoltage and

undervoltage

EN 50155 Overvoltage 140%

Residual voltage 60%

100 ms & 1000 ms

100 ms

Radiated emission EN 55011

Limits: EN 50121-3-2

Enclosure measurement 40 dBµV/m QP

30 – 230 MHz

47 dBµV/m QP

230 – 1000 MHz

Conducted emission EN 55011

Limits: EN 50121-3-2

Power port measurement 99 dBµV QP

0.15 – 5 MHz

93 dBµV QP

5 – 30 MHz

Signal port measurement 99 dBµV QP

0.15 – 5 MHz

93 dBµV QP

5 – 30 MHz

Environmental

Temperature Operating –40 to +70°C* (–40 to +158°F)

Storage & Transport –40 to +70°C (–40 to +158°F)

Humidity Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2 000 m / 70 kPa

Reliability prediction (MTBF) MIL-HDBK- 217F Operating 306 115 h

IEC 60068-2-64 Operating Vertical 2.0 m/s² Transverse

2.0 m/s² Longit. 2.0 m/s²

Non operating 11.4 m/s²

Shock IEC 60068-2-27 Operating 10 g, 30 ms Half sine ±3 shocks

IEEE 1478 Operating 20 g, 11 ms Saw tooth ±3 shocks

Packaging

Dimension W x H x D 175 x 100 x 144 mm

Weight 2295 g

Degree of protection IEC 529 Enclosure IP65**

Cooling Convection

Mounting Rear panel wall mounting

* Refer to “Safety” section

** Provided all connectors are connected with IP65 cabling or fitted with protective caps (delivered with the unit),

tightened to the specified torque

6641-2222

Description

Functional description

RFR-12-FB is switch developed for rail on board and industrial applications approved

according to EN 50155. To meet the environmental requirements from rail and harsh

industrial applications the switch has rugged M12 Ethernet connectors and full metal

housing. The switch fulfill IP 65 degree of protection. Our unique FRNT (Fast Recovery

of Network Topology) technology is the fastest protocol on the market to re-configure

a network in the event of any failure of a link or hardware. Real-time properties are

implemented in the RFR-12-FB in order to achieve determinism for real time critical

applications. The switch also supports QoS (Quality of Service) with four priority queues

and strict priority scheduling as well as HoL (Head of Line Blocking Prevention). All to

assure that the data network is deter ministic. RFR-12-FB also has a by-pass relay that

by-pass the unit in case of power loss to the switch.

6641-2222

Interface specifications

Power

Rated voltage 24 to 110 VDC

Operating voltage 16.8 to 143 VDC

(14.4 to 154 VDC for 100 ms)

Rated current 580 mA @ 24 VDC

140 mA @ 110 VDC

Inrush current 5 mA²s @ 24 VDC

22 mA²s @ 110 VDC

Startup current

(Power source capability)

600 mA @ 24 VDC

275 mA @ 110 VDC

Polarity Reverse polarity protected

Redundant power input No

Isolation to All interfaces and chassis

Galvanic connection to None

Connection M12 A-coded male

Connector size 0.2 – 2.5 mm² (AWG 24 – 13)

Shielded cable Not required

Miscellaneous –

M12 A-Coded Power Connector

Position Direction Description

1 U+ Positive supply voltage

2 – –

30 V 0 V

4 – –

Housing Shield Chassis of product (ground)

2 1

3 4

6641-2222

Ethernet TX (both switch, router and coupler ports)

Electrical specification IEEE std 802.3. 2000 Edition

Data rate 10 Mbit/s or 100 Mbit/s, manual or auto

Protocol –

Duplex Full or half, manual or auto

Circuit type TNV-1

Transmission range 100 m

Isolation to All interfaces and chassis

Galvanic connection to None

Connection M12 D-coded

Shielded cable Ye s

Conductive housing Ye s

Miscellaneous –

Number of ports 12

M12 D-coded, 10/100Base-TX

Position Direction Description

1 Out Transmit Data +

2 In Receive Data +

3 Out Transmit Data –

4 In Receive Data –

Housing Shield Chassis of product (ground)

Table des matières

Autres manuels Westermo Routeur réseau

Westermo

Westermo Viper 408 Manuel utilisateur

Westermo

Westermo DDW-02-B1 Manuel utilisateur

Westermo

Westermo MRD-310 Manuel utilisateur

Westermo

Westermo RT-370 Manuel utilisateur

Westermo

Westermo RedFox Rail Manuel utilisateur

Westermo

Westermo MRD-350 Manuel utilisateur

Westermo

Westermo MR-210 Manuel utilisateur

Westermo

Westermo MRD-405 Manuel utilisateur

Westermo

Westermo Ibex-630 Series Manuel utilisateur

Westermo

Westermo Ibex-RT-630 Series Manuel utilisateur

Westermo

Westermo DR-260 Manuel utilisateur

Westermo

Westermo RFI-219-T3G Manuel utilisateur

Westermo

Westermo MRD-415 Manuel utilisateur

Westermo

Westermo Lynx 5600 Series Manuel utilisateur

Westermo

Westermo DR-200 Manuel utilisateur

Westermo

Westermo Lynx DSS Manuel utilisateur

Westermo

Westermo BRD-355A Manuel utilisateur

Westermo

Westermo ADSL-350 Manuel utilisateur

Westermo

Westermo Ibex-330 Series Manuel utilisateur

Westermo

Westermo BRD-355 Manuel utilisateur

Westermo

Westermo SDW-550 E-mark Manuel utilisateur

Westermo

Westermo Viper-12 Series Manuel utilisateur

Westermo

Westermo LRW-112 Series Manuel utilisateur

Westermo

Westermo Lynx Plus Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité