Vivotek AM-520 Manuel utilisateur
IP Surveillance
Installation Guide
VIVOTEK Fixed Dome & PTZ Series
Mounting Cap
Using AM-520 mounting cap
and compatible accessories
Rev. 1.5
2
180
3/4"NPT
M6
52.2
17
1-1/2"
C
C
20
AM-520 Mounting Cap Mechanical Drawings
Revision History:
* Rev. 1.0: Initial Release
* Rev. 1.1: Added supported models
* Rev. 1.2: Threads have been added to the exterior for mount poles. Added FE8181 series to the list of
supported models.
* Rev. 1.3: Added supported models. * Rev. 1.4: Updated mechanical drawings.
* Rev. 1.5: Added supported models.
Compatible VIVOTEK Cameras
I
Fixed Dome series FD8361 / FD8361L / FD8362 /FD8362E / FD8363 / FD8335H/ FD8372 /
FD8162 / FD8135H / FD8163 / FD8131V / FD8133V/ FD8134V / MD7530
/ MD7560 / MD8562 / FD8164 / FD8137H / FD8131 / FD8133 / FD8134
/ F8173 / FD8164V / FD8137HV / FD8167 / FD8167-T / FD8138-H /
FD8367-V / FD8367-TV / FD8338-HV
Fisheye series FE8172V / FE8171V / FE8174/ FE8174V / FE8181 / FE8181V / FE9181-H
/ FE9182-H / FE9381-EHV / FE9382-EHV / FE9191 / FE9391-EV /
FE9582-EHNV
You may also refer to VIVOTEK's website for the list of supported models. Support for other models can
be available through time.
3
English
Installation
II
Above are the locations of different groups of mounting holes for matching different
cameras:
Hole
Type
Applicable Cameras Screw No. of
screws
Screw
pack
AFD8361 / FD8361L / FD8362 /FD8362E / FD8363
/ FD8335H/ FD8372
M5X10 round
head 4A
B
FD8162 / FD8135H / FD8163 / FE8181 /
FE8181V / FE9182-H / FE9382-EHV / FE9391-
EV / FE9582-EHNV
M4X12 round
head 3 or 2 B
CFD8131V / FD8133V/ FD8134V M3X6 round
head 3C/E/F/K
DFE8171V / FE8172V / FE8174V / FE9381-EHV M3X8 binding
head 3D/L/J
EMD7530 / MD7560 / MD8562 M3X6 round
head 3C/E/F/K
FFD8164 / FD8137H M3X6 round
head 3C/E/F/K
HFD8131 / FD8133 / FD8134 M3X6 round
head 2H
IFE8172 / FE8173 / FE8174 / FE9181-H / FE9191 M3X8 binding
head 4I
JFD8167 / FD8167-T / FD8138-H M3X8 3D/L/J
KFD8164V / FD8137HV M3X6 round
head 3C/E/F/K
LFD8367-V / FD8367-TV / FD8338-HV M3X8 3D/L/J
Mounting Hole Denitions
4
Refer to the table below for the description of the included screws:
Screw Description No. of
screws
Material char.
M5X10 (A) 4
M4X12 (B) 3
M3X6 (C/E/F/K) 3
M3X8 (D/L/J) 3
M3X6 (H) 2
M3X8 (I) 4
Hex wrench and hex
socket screw
1
NOTE:
1. Route cables before you secure the accessories to a wall.
2. For details on the cable connections with each camera, please refer to their Quick
Installation Guide.
For cabling and conguration details with each network camera, please refer to their
documentation.
5
English
Conguration - Pendant Pipe
276 mm
180 mm
AM-118
AM-116
AM-520
476 mm
180 mm
AM-118
AM-117
AM-520
AM-118
3/4" Female adapter
3/4" pendent pipe
AM-520
AM-522
180 mm
Note: The 3/4" female adapter is separately purchased.
6
Conguration - Wall Mount
AM-212
HEX SOCKET SCREW
AM-520
7
English
Conguration - Gooseneck
AM-221
AM-520
HEX SOCKET SCREW
NOTE:
When installing the mounting cap, take note that the orientation of the mounting cap can
affect the camera's shooting direction. You may need to remove the mounting cap, rotate,
and re-install it for the best orientation. Use the hex wrench to tighten its retention hex
socket screw when done.
8
H holes
M3X6 Screws
RJ-45
coupler
Refer to the matching table on page 4 for the mounting hole information for your camera.
Installing Camera to Mounting Cap
1. You should route cables through other accessories before you install cameras to the
mounting cap.
2. Route power lines and other cables through the mounting cap.
3. Orient and install the camera to the mounting cap.
4. Connect cables to the camera.
5. Install the mounting cap to other accessories, e.g., wall-mount bracket.
6. Proceed with initial setup such as enabling network access, focus tuning, or zooming.
When done, secure the outer dome cover.
FD8134
Some installation samples are shown below:
9
English
Note that for cameras that come with cable glands, e.g., FD8134 and FD8134V, it can be
tricky passing them through a 3/4" pendant pipe.
1
2
From local network
1. You can pass the cable gland and other wires
into or through the pendant pipe, while leaving
the RJ-45 connector behind.
2. Route another Ethernet cable from the local
network through the other end of the pendant
pipe.
3. You can then install the pendant pipe.
10
RJ-45 coupler
You can then connect the RJ-45 from the camera with that from the local network using an
RJ-45 coupler. When done, press the coupler and the cables into the recess of the bracket.
Align and install the camera to the bracket.
Table des matières
Autres manuels Vivotek Accessoires pour appareils photo
Vivotek
Vivotek AE-252 Manuel utilisateur
Vivotek
Vivotek IP8152 Manuel utilisateur
Vivotek
Vivotek AE-153 Manuel utilisateur
Vivotek
Vivotek AE-237 Manuel utilisateur
Vivotek
Vivotek CaMate Series Manuel utilisateur
Vivotek
Vivotek Fixed Dome Series Manuel utilisateur
Vivotek
Vivotek AM-21C Manuel utilisateur
Vivotek
Vivotek IB836BA-HT Manuel utilisateur
Vivotek
Vivotek AE-238 Manuel utilisateur
Vivotek
Vivotek AM-516 Manuel utilisateur
