Vivotek AM-108 Manuel utilisateur
AM-108
Installation Guide
Orderig P/N: 100187100G
Package Contents
Installation
0002D10766AD
SC811
1
2
•
Screw pack: M3x8, M3x20,
M3x15 hex stando spacer
Main bracket In-ceiling bracket Trim panel
Screw cap sticker
5 ~ 25.4mm
90mm
220mm
Drill or cut a square hole on the ceiling panel. The dimensions are shown below.
The thickness of ceiling panel can be between 5 to 25.4mm.
Remove the original mount screws from the back of SC8131 camera. 3Secure the camera to the main bracket by driving 2 M3x8 screws.
4Put the in-ceiling bracket into the square hole.
Do not remove the protective sheet on the camera lenses until the installation is
done.
5Jot down the camera's MAC address before proceeding with the installation.
Recommended Installation Height
•Installation Height: 2.4M ~ 3.6M
•Coverage area: 1.7M ~ 5.1M
Height
HFOV
VFOV
2 2
Camera Installation Height (cm) HFOV (cm) VFOV (cm)
240 234 167
260 281 201
280 327 234
300 374 268
320 421 302
340 468 335
360 515 369
The ribbed side is on top of ceiling panel.
Max. 45°
7Connect the safety tether wire from the in-ceiling bracket to the main bracket.
6Drive 2 screws (M3x20) to the mounting holes on the in-ceiling bracket.
Route and connect an Ethernet cable to the camera's RJ45 port, if you already
mount the ceiling panel.
8Match the keyhole slots to the installed screws.
9Install the camera and the main bracket by aligning the key slot holes with the
screw heads. Slide the main bracket to the left and secure the bracket with another
2 M3 screws.
Tilt the camera and use tools such as a spirit level to ensure the camera is installed
level.
10
11 12 Tighten the tilt retention screws when camera is level.
If the ceiling panel is thicker than 20mm, use the copper hex stando spacers
instead.
if ≥ 20mm
The bracket can also be installed without the in-ceiling bracket using the 4 holes
on the corners.
Install the trim panel, and attach the screw cap stickers.
SC8131
Browser
LAN
Shepherd
??? cm
User name: root
Password: root
13 14 15
16 17 17
Remove the protective sheet in front of the camera. Measure the distance (installation height) between the camera lens and the
ground.
Visist VIVOTEK's website and download the Shepherd utitlity. Run and use the
Shepherd utility to nd the camera in a local network.
Open a web console to the camera. Start your conguration such as entering the camera's installation height.
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
VIVOTEK Europe
Randstad 22-133, 1316BW Almere, The Netherlands
T:+31(0)36-5298-434 E:[email protected]
All specications are subject to change without noice.
Copyright © 2020 VIVOTEK INC. All rights reserved.
Table des matières
Autres manuels Vivotek Accessoires pour appareils photo
Vivotek
Vivotek Fixed Dome AM-116 Manuel utilisateur
Vivotek
Vivotek Bullet Series Manuel utilisateur
Vivotek
Vivotek AM-516 Manuel utilisateur
Vivotek
Vivotek AM-21C Manuel utilisateur
Vivotek
Vivotek AE-237 Manuel utilisateur
Vivotek
Vivotek CaMate Series Manuel utilisateur
Vivotek
Vivotek IP8152 Manuel utilisateur
Vivotek
Vivotek AE2000 Manuel utilisateur
Vivotek
Vivotek Fixed Dome Series Manuel utilisateur
Vivotek
Vivotek AE-153 Manuel utilisateur
