Velleman K8095 Manuel utilisateur

K8095

ILLUSTRATED ASSEMBLY MANUAL H8095IP-1

Total solder points: 230

Difficulty level: beginner 1 2 3 4 5 advanced

Create yourownhome audio system,

juxe box,jingle player,sound effects,...

MP3 PLAYER KIT

Break off.

PCB for

vertical mount

*In the picture is shown:

- Optional LCD type PC1602W RS-KWA-E

- Some horizontal type push buttons type PS-04PV

- RF receiver modules type RX433N

- SD card (not included)

Features

 SD card operation

 high-quality VLSI decoder

 5 Preset folder access buttons

 play-pause, next, previous, search

 volume control

 random and shuffle

 8 different preset sound modes

 6 play modes: All, Folder, At power-on...

 infrared receiver

 on-board power amplifier

 RCA pre out

 headphone and speaker outputs

 mono operation is possible

 vertical or horizontal SD position possible

 suits commercially available LCD types

Features & Specifications

Specifications

 suitable for SD and SDHC cards

 tested up to 32GB cards

 supports ID3 TAG information: Title, Artist Name, Album

Name and Year are displayed on the (optional) 2-line 16 char.

LCD

 supports folders to one level deep

 up to 1024 folders, each containing up to 16384 songs

 equalizer settings: Flat , Loudness, Heavy, Clear, Soft, Disco,

Live and Hall

 decodes MP3 (MPEG 1.0 & 2.0 audio layer III (CBR, VBR,

ABR), till 320kbit/s. Fraunhofer IIS and Thomson licensed

 amplifier: 2x 5Wrms @ 4ohm

 power supply: 12Vdc/1A

Optional:



LCD: PC1602WRS-KWA-E

 RF receiver module: RX433N

 power adaptor: PS1210

 RF remotes: for EU and US

 8-channel RF remote transmitter: VM118R (assembled) / K8058 (Kit-version)

 RF remotes: only for EU:

 4-channel desktop transmitter: VM160DT

 4-channel transmitter: VM160T

 IR remotes: 15-channel IR transmitter: K8049 (Kit-version)

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will

protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒Make sure the skill level matches your experience, to avoid disappointments.

⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒Perform the assembly in the correct order as stated in this manual

⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒Values on the circuit diagram are subject to changes.

⇒Values in this assembly guide are correct*

⇒Use the check-boxes to mark your progress.

⇒Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

Assembly hints

DO NOT BLINDLY FOLLOW THE ORDER OF THE

COMPONENTS ONTO THE TAPE. ALWAYS CHECK

THEIR VALUE ON THE PARTS LIST!

Important

Thanks a lot for buying this MP3 player project.

For your convenience, the MP3 decoder circuit is pre assembled on a plug-in board. This kit allows you to create

a full customized MP3 player, build completely to you wishes.

Standard only infrared receiver is included to work with our K8049 but an optional RF receiver can be mounted,

for use with our transmitters VM118R - K8058 or remotes VM160T or VM160DT (DeskTop version).

The board can be used vertically or horizontally. For vertical mount , a sub board for the SD card holder is

provided. There can be mounted several types of buttons (standard all small vertical types), optionally

horizontal types can be used, or types with a longer actuator. The optional LCD uses a standard 4 bit nibble

mode, so most 2 line 16 character LCD modules can be used.

Download the user manual on our web site (check the K8095 product page)

IMPORTANT!

CAUTION:

This preassembled board contains an expensive MP3 decoder chip.

This board has been fully tested before shipping.

Treat this board with caution and mind static electricity.

Always touch an earthed metal part before handling this board.

This board contains the connector for an optional LCD, the connector must be

broken off.

The board has a V-cut slot; carefully break off this part from the MP3 decoder

board along the slot.

 D1 : BAT85

 D2 : 1N5400

2. Diode. Watch the polarity!

D...

CATHODE

 IC1 : 8p

 IC3 : 28p

3. IC socket. Watch the

position of the notch!

 RV1 : 10K

Contrast

4. Trim potentiometer

 LD1 : 3mm red

 LD2 : 3mm red

 LD3 : 3mm red

 LD4 : 3mm red*

* LD4 is not mounted if an optional

LCD is used with backlight

5. LED. Watch the polarity!

Construction

 J6 : MP3 decoder board

 J10 : LCD unit board

6. Board-edge connector

 R1 ... R8 : 47 (4 - 7 - 0 - B)

 R9 ... R12 : 100 (1 - 0 - 1 - B)

 R13, R14 : 180 (1 - 8 - 1 - B)

 R15 : 220

(2 - 2 - 1 - B)

 R16 : 560

(5 - 6 - 1 - B)

 R17 : 680

(6 - 8 - 0 - 0 - 1)

 R18 ... R24 : 1K (1 - 0 - 2 - B)

 R25, R26 : 1K1 (1 - 1 - 0 - 1 - 1)

 R27 : 2K4 (2 - 4 - 0 - 1 - 1)

 R28 ... R34 : 10K (1 - 0 - 3 - B)

 R35 : 100K

(1 - 0 - 4 - B)

1. Horizontal resistors

R...

7. Push buttons

 SW1 Play/pause  SW8 A

 SW2 Previous  SW9 B

 SW3 Next  SW10 C

 SW4 Up  SW11 D

 SW5 Down  SW12 E

 SW6 Select  SW13 remote

 SW7 random

D2 not on tape! Optional for SW1 ... SW7

construction

 SK1 :2p (mono/stereo)

mounted = mono output

 J8 :5p (LCD)

Mount a shunt if no LCD

will be mounted.

11. Pin header

 T1: BC337

10. Transistors

 J5 (power supply)

14. Connector

 IRX1 :BRM-1040

12. IR-demodulator

1 2 3

 X1 : 12.000MHz

13. Crystal

 C1…C4 :10pF (10)

 C5, C6 :22pF (22)

 C7, C8 :10nF (103)

 C9...C16 :100nF (104)

 C17, C18 :220nF (224)

8. Capacitors.

 J2

9. Male PCB connector

LCD

Construction

 IC2 : TDA1517

18. Stereo amplifier

 C21 ... C23 : 1000µF

C...

19. Electrolytic Capacitor.

Watch the polarity !

 IC1 :VK8095 - IC1

“RF-decoder”

(programmed PIC12F629)

 IC3 : VK8095 - IC3

“CPU” (programmed

PIC18F26J11-ISP)

21. IC. Watch the

position of the notch!

 VR1 :UA7805

 VR2 : LM317

20. Voltage regulator

Make sure the metal back

of both voltage regulators

do not touch each other.

 C19 : 10µF

 C20 : 100µF

C...

15. Electrolytic Capacitor.

Watch the polarity !

 J3 : 3.5mm

(Headphones)

16. stereo phone jack

 J4 : Line out

17. RCA connector

Watch the

position of the

notch!

construction

The Sd-card holder can be mounted vertically and horizontally.

Horizontal posittion:

Mount the card-holder ont the solderside of the main pcb (fig. 1)

Vertical posittion:

1. Remove the alternative PCB, to be used for the vertical mounting of the SD card

holder, from the main PCB (fig. 2).

2. Turn over the alternative PCB allowing you to mount the SD card holder (fig. 3).

3. Insert a pin into each connection and bend each one of those pins (fig. 4).

4. Mount the assembly onto the main PCB and solder the connections (fig. 5).

22. SD-card holder

BREAK OFF

10X

The mounting procedure for the

RF-receiver and LCD-display

can be found on our website:

www.velleman.eu

23. MP3 unit

Pay attention to the mounting

order of the MP3 unit !

Insert the pre-assembled and

tested MP3 decoder.

Construction

24. Rubber feets

Mount the rubber feet on the

solder side of the PCB.

25. Optional

RF-receiver:

For RF remote use, mount an

RX433 module. See picture on

the box.

LCD-display:

If an LCD is used, mount the

optional PCI602WRS-KWA-E

LCD. Use the edge board to

connect the LCD.

See picture on the box.

Autres manuels pour K8095

Table des matières

Autres manuels Velleman Unité de contrôle

Velleman

Velleman VMA436 Manuel utilisateur

Velleman

Velleman ARDUINO VMA308 Manuel utilisateur

Velleman

Velleman VMA310 Manuel utilisateur

Velleman

Velleman VMA325 Manuel utilisateur

Velleman

Velleman VSC1 Manuel utilisateur

Velleman

Velleman ARDUINO VMA307 Manuel utilisateur

Velleman

Velleman VM106 Manuel utilisateur

Velleman

Velleman VMA341 Manuel utilisateur

Velleman

Velleman Whadda WPM300 Manuel utilisateur

Velleman

Velleman K4400 Manuel utilisateur

Velleman

Velleman VMA328 Manuel utilisateur

Velleman

Velleman VMM006 Manuel utilisateur

Velleman

Velleman Whadda WPI471 Manuel utilisateur

Velleman

Velleman WPM400 Manuel utilisateur

Velleman

Velleman K2664 Manuel utilisateur

Velleman

Velleman HAA80 Manuel utilisateur

Velleman

Velleman VMM005 Manuel utilisateur

Velleman

Velleman VMA402 Manuel utilisateur

Velleman

Velleman Whadda WPSE477 Manuel utilisateur

Velleman

Velleman Whadda WPM457 Manuel utilisateur

Velleman

Velleman VMA338 Manuel utilisateur

Velleman

Velleman K8006 Manuel utilisateur

Velleman

Velleman VMA410 Manuel utilisateur

Velleman

Velleman VMA319 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur