Ubiquiti PowerBeam M Manuel utilisateur

High-Performance

Integrated InnerFeed™

airMAX®Bridge

Model: PBE-M5-400

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam™.This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

If you want to add a radome to enclose the Dish Reflector,

UbiquitiNetworks offers the PowerBeam Radome, 400 mm,

modelPBE-RAD-400 as an optional accessory. Product details are

available on our website at www.ubnt.com/airmax

Package Contents

Dish Reflector PBE-M5-400

Antenna Feed*

Rear Housing

Dish Bracket Pole Clamp U-Bolt Flange Nuts

(M8, Qty. 2)

High-Performance

IntegratedInnerFeed™

airMAX®Bridge

Model:PBE-M5-400

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start Guide

* The PBE-M5-400 Antenna Feed has a thin gray ring around the center of

the cap to differentiate it from the PBE-M5-300 Antenna Feed.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is already poweredon. Alternatively, the PowerBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light green when the wireless signal

strength is above -65 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light red when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light green when the

device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The PowerBeam mounted outdoors without the Dish Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter-clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

push until they lock intoplace.

*640-00073-05*

640-00073-05

3. Push in the sides of the Cable Door and detach it from the

Rear Housing.

4. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Slide the Pole Clamp onto the Dish Bracket.

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket.Secure

each end of the U-Bolt with a Flange Nut.

25 N-m

Note: The mounting assembly can accommodate a

Ø 32 - 56 mm pole.

8. Optional: If you have the PowerBeam Radome (optional

accessory), then align the arrows on the bottoms of the

Radome and Dish Reflector so the Drain Holes on the Radome

point downward. Snap the Radome onto the Dish Reflector.

9. Connect the Ethernet cable from the PowerBeam’s Ethernet

port to the POE port of the Gigabit PoE adapter.

10. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

11. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ubiquiti Point d'accès sans fil

Ubiquiti

Ubiquiti BulletAC-IP67 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP-AC PRO Manuel utilisateur

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-Omni Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UAP--AC--HD Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Manuel utilisateur

Ubiquiti

Ubiquiti AirCube ACB-AC Manuel utilisateur

Ubiquiti

Ubiquiti Loco5AC Manuel utilisateur

Ubiquiti

Ubiquiti UAP-PRO UNIFI Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF-11FX Manuel utilisateur

Ubiquiti

Ubiquiti Power AP N 802.11n Manuel utilisateur

Ubiquiti

Ubiquiti IsoStation AC IS-5AC Manuel utilisateur

Ubiquiti

Ubiquiti UAP Manuel utilisateur

Ubiquiti

Ubiquiti AirFiber X AF-5G34-S45 Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam AC GENZ Manuel utilisateur

Ubiquiti

Ubiquiti RocketM Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti PBE-5AC-400-ISO-EU Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam m5 iso PBE-M5-300-ISO Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AC MESH PRO Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-PRO Manuel utilisateur

Ubiquiti

Ubiquiti BULLETM2-HP-US Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Wifi BaseStationXG Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP AC SHD Manuel utilisateur

Ubiquiti

Ubiquiti UAP Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur