Ubiquiti AirFiber AF-11FX Manuel utilisateur

airFiber AF-11FX Zip Ties (Qty. 2) airFiber Gigabit PoE (50V,

1.2A)

Power Cord

Package Contents

Antenna Compatibility

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

The airFiber AF-11FX radio is designed for use with the airFiber X antenna model AF-

11G35*.

* Check your local/regional regulations for the antenna gain allowed for your application

Installation Requirements

Clear line of sight between airFiber radios

Vertical mounting orientation

Mounting point:

At least 1 m below the highest point on the structure

For tower installations, at least 3 m below the top of the tower

Ground wires – min. 10 AWG (5 mm ) and max. length: 1 m. As a safety precaution,

ground the airFiber radio to grounded masts, poles, towers, or grounding bars.

WARNING: Failure to properly ground your airFiber radio will void your

warranty.

(Recommended) 2 Outdoor Gigabit PoE surge protectors

Note: For guidelines about grounding and lightning protection, follow your

local electrical regulatory codes.

High-Band Duplexer(s) (model AF-11FX-DUP-H) or Low-Band Duplexer(s) (model

AF-11FX-DUP-L) are required for proper operation:

SISO mode: One Duplexer of either band type

MIMO mode: Two Duplexers of the same band type

Note: Duplexers must be purchased separately. The Duplexer(s) must

match the terms of your license (frequency bands and polarities allowed).

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

(Optional) If not using PoE: DC power source and 12/30 AWG power cable

Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are

required for all wired Ethernet connections.

Hardware Overview

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Chain 0 / Chain 1

Signal LEDs

Low-Band Duplexer High-Band Duplexer

When the Chain 0 or Chain 1 duplexer is installed, its N-type connector is located

here, allowing connection to an RF cable (Chain 1 is covered by the removable

duplexer cap).

Signal 4 LED will light blue when on.

Signal 3 LED will light green when on.

Signal 2 LED will light yellow when on.

Signal 1 LED will light red when on.

Bootup to airOS When powering on, the Power, MIMO, LINK, and Signal 1-4 LEDs

light on. Once the CPU code takes over, the MIMO, LINK, and Signal 1-3 LEDs turn

off. Signal 4 LED remains lit to indicate the boot sequence is underway.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Link LED

Initializing airFiber Software When the airFiber application begins to boot under

airOS®, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until

the AF‑11FX is fully booted.

Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how

close the AF‑11FX is to ideal aiming. This is auto-scaled based on the link range, the

antenna gains, and the configured TX power of the remote AF‑11FX. Each Signal

LED has three possible states: On, Flashing, and Off. All Signal LEDs would be

solidly on in an ideal link. For example, if the link has a 1 dB loss, the Signal 4 LED

will flash; a 2 dB loss and the Signal 4 LED will turn off. The full bar graph LED

states are shown below.

dB loss

0 -1 -2 -3 -4 -5 -6

-7 -8 -9 -10 -11 -12 -13

Off RF Off

Syncing

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

MIMO LED

MGMT LED

Data LED

Power LED

Beaconing

Registering

On Operational

Off Radio Configured in SISO Mode

On Radio Configured in MIMO Mode

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Off No Power

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Management Port

Reset Button

Data Port

VDC IN

TX 0, RX 0

RX 1, TX 1

On Powered On

10/100 Mbps, secured Ethernet port for configuration. In-Band Management is

enabled by default in the airFiber Configuration Interface. When In-Band

Management is disabled, the MGMT port is the only port that can monitor, configure,

and/or update firmware.

To reset to factory defaults, press and hold the Reset button for more than 10

seconds while the device is already powered on.

Gigabit PoE port for handling all user traffic and powering the device.

The terminal block can be used to power the AF-11FX with +50VDC, 1.2A instead of

PoE.

The TX and RX SMA ports for the Chain 0 Low-Band Duplexer or High-Band

Duplexer (SISO and MIMO modes).

The RX and TX SMA ports for the Chain 1 Low-Band Duplexer or High-Band

Duplexer (MIMO mode only). In SISO mode, these unused ports are protected by

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

N Connector

SMA Port

the duplexer cap.

Female N-type connector into which the antenna cable is plugged.

High-band and low-band channel SMA ports.

Note: Duplexers are not included with the AF-11FX. SISO mode requires one

Low-Band Duplexer or one High-Band Duplexer. MIMO mode requires either

two Low-Band Duplexers or two High-Band Duplexers.

Installation Overview

We recommend that you configure your paired AF-11FX radios before site installation.

The overview below summarizes the installation procedure, and the subsequent

sections provide detailed installation information.

Install the Duplexer(s) in the AF-11FX radio.

Connect the airFiber Gigabit PoE adapter to the DATA port, and connect your

computer to the MGMT port.

Configure the AF-11FX.

Install a ground wire and mount the AF-11FX on the airFiber AF-11G35 antenna (or

a compatible antenna).

At the installation site, install the antenna with the mounted AF-11FX radio (see the

antenna’s Quick Start Guide for installation instructions).

Connect the DATA port to your LAN, and connect power (PoE or DC power) to the

AF-11FX.

Establish and optimize the RF link.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Autres manuels pour airFiber AF-11FX

Table des matières

Autres manuels Ubiquiti Point d'accès sans fil

Ubiquiti

Ubiquiti UAP-AC-HD Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Wifi BaseStationXG Manuel utilisateur

Ubiquiti

Ubiquiti Edge Point EP-R8 Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam ac ISO Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UAP-AC-PRO Manuel utilisateur

Ubiquiti

Ubiquiti Power AP N 802.11n Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-IW Manuel utilisateur

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation M2 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP AC Lite Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF-11 Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-M-PRO Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-SHD Manuel utilisateur

Ubiquiti

Ubiquiti UAP Manuel utilisateur

Ubiquiti

Ubiquiti airCube ISP Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Omni Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Stadium XG Manuel utilisateur

Ubiquiti

Ubiquiti LTU-Pro Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF 60 Manuel utilisateur

Ubiquiti

Ubiquiti AmpliFi MeshPoint HD Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP AC Lite Manuel utilisateur

Ubiquiti

Ubiquiti NanoBridge M5 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur

Ubiquiti airFiber AF-11FX Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques