Ubiquiti UAP Manuel utilisateur

802.11n Wi-Fi Access Point

Models:

UAP, UAP-LR (Long-Range)

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®AP.

This Quick Start Guide is designed to guide you through

installation and also includes warranty terms.

Package Contents

UniFi AP Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(M3x50, Qty. 3)

Keps Nuts

(M3, Qty. 3)

Screws

(M2.9x20, Qty. 3)

Screw Anchors

(M3x20, Qty. 3)

802.11n Wi-Fi Access Point

Models:

UAP,UAP-LR (Long-Range)

PoE Adapter (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start Guide

Installation Requirements

• CAT5/6 cable

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 25 mm hole for

Ethernet cable feed)

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, and Dynamic Frequency Selection (DFS) requirements.

System Requirements

• Microsoft Windows 7/8, MacOSX, or Linux

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

• UniFi Controller software (available at:

downloads.ubnt.com/unifi)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A management station computer running the UniFi

Controller software, located either on-site and connected to

the same Layer-2 network, or off-site in a cloud or NOC

NetworkHealth

www WAN LAN

WLAN

VOIP

www WAN LAN WLAN VOIP

DNS

GATEWAY

ACTIVECLIENTS

DOWN

SWITCHES

USERS

GUESTS

DOWN

APS

USERS

GUESTS

DOWN

PHONES

EXTENSION

CALLSIN

CALLSOUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX 192

162

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENTSITE

Default

REFRESHRATE

2minutes

NetworkHealth

www WAN LAN

WLAN

VOIP

www WAN LAN WLAN VOIP

DNS

GATEWAY

ACTIVECLIENTS

DOWN

SWITCHES

USERS

GUESTS

DOWN

APS

USERS

GUESTS

DOWN

PHONES

EXTENSION

CALLSIN

CALLSOUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX 192

162

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENTSITE

Default

REFRESHRATE

2minutes

O-Site

Cloud/NOC

On-Site

Management

Station

UniFi Switch

UniFi

Security

Gateway

Internet

LAN

WAN

Wired UAP/UAP-LR

Wireless

Uplinked1

UAP/UAP-LR

Sample Network Diagram

1. To set up wireless-uplinked APs, refer to the User Guide on the website:

documentation.ubnt.com/unifi

2. All UniFi devices support off-site management controllers. See the User

Guide for setup details.

Hardware Overview

LEDs

LED Color Status

Flashing Amber Initializing.

Steady Amber Factory default, waiting to be integrated.

Alternating

Amber/Green

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Quickly

Flashing Green

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Green

Indicates the device has been successfully

integrated into a network and is working

properly.

Steady Green

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Ethernet Port Reset Button

Locking

Notch

Ethernet The 10/100 Ethernet port is used to connect the

power and should be connected to the LAN and DHCP server.

Power can be provided by any of the following:

• Included PoE Adapter

• Ubiquiti Networks UniFi Switch

• Ubiquiti Networks TOUGHSwitch™ PRO

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds until the LED

turnsoff.

Locking

Clip

Mounting

Bracket

Locking Clip During installation, the Locking Clip on the

Mounting Bracket locks into the Locking Notch on the UniFi AP

to help prevent theft.

Hardware Installation

The UniFi AP can be mounted to the wall or ceiling. Perform

the steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the cable feed slot pointed towards the floor.

2. Use a pencil to mark the three holes on the wall. Use a

6mm drill bit to drill the holes.

Optional 25 mm Hole

for Ethernet Cable

Feed through Wall

3. If your Ethernet cable feeds through the wall, cut or drill

a circle approximately 25 mm in diameter, just below the

bottom center of the Mounting Bracket (as shown above).

Then feed the CAT5/6 cable through the hole.

*640-00203-01*

640-00203-01

4. Insert the Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

5. Connect the Ethernet cable to the Ethernet port.

6. Align the notch on the UniFi AP with the notch on the

Mounting Bracket.

7. Turn the UniFi AP clockwise until it locks into place.

Ceiling Mount

1. Remove the ceiling tile.

2. Place the Mounting Bracket in the center of the ceiling tile.

Mark the three mounting screw holes and 25 mm hole for

the Ethernet cable.

25 mm Hole for

Ethernet Cable Feed

3. Use a 3 mm drill bit to drill the screw holes, and cut or drill

the 25 mm hole for the Ethernet cable feed.

4. Secure the Mounting Bracket to the ceiling tile using the

Ceiling Backing Plate, Flathead Screws, and Keps Nuts. Then

feed the Ethernet cable through the 25mmhole.

Autres manuels pour UAP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ubiquiti Point d'accès sans fil

Ubiquiti

Ubiquiti Rocket 5ac PtMP Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP AC Lite Manuel utilisateur

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Manuel utilisateur

Ubiquiti

Ubiquiti UAP-AC-LITE-5 Manuel utilisateur

Ubiquiti

Ubiquiti BulletM2-HP Manuel utilisateur

Ubiquiti

Ubiquiti Edge Point EP-R8 Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation 5AC Loco Manuel utilisateur

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti NanoBeam 5AC Gen 2 NBE-5AC-Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP BeaconHD Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF-11 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Manuel utilisateur

Ubiquiti

Ubiquiti R5AC-PTP Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UBB Manuel utilisateur

Ubiquiti

Ubiquiti UniFi AP XG Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Manuel utilisateur

Ubiquiti

Ubiquiti UniFi nanoHD AP Manuel utilisateur

Ubiquiti

Ubiquiti airFiber AF-11 Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Ubiquiti

Ubiquiti Rocket2AC Prism Manuel utilisateur

Ubiquiti

Ubiquiti UAP-PRO Manuel utilisateur

Ubiquiti

Ubiquiti Rocket5AC R5AC-PTP Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation M Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Enterprise AP Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur