Ubiquiti EdgeSwitch 16XP Manuel utilisateur
Rack-Mount
Power over Ethernet
Managed Switches
Model: ES-16XP
Introduction
Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®
16XP. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
Package Contents
EdgeSwitch 16XP
Flathead Screws
(Qty. 2)
Phillips Screws
(Qty. 4)
Cage Nuts
(Qty. 4)
Rack-Mount
Powerover Ethernet
ManagedSwitches
Model:ES-16XP
Power Cords (Qty. 2) Quick Start Guide
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet
cable and earth grounding must be used for outdoor installations as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, and Dynamic Frequency Selection (DFS) requirements.
Hardware Overview
Aand Bdesignate the two 8-Port EdgeSwitch devices housed
in the rack. This may be useful for the Location setting on the
Device tab in the Configuration Interface.
Front Panel Ports
Management Ports 1-8
ResetUSB
Management Ports 1-8
ResetUSB
EdgeSwitch A EdgeSwitch B
Interface Description
Management 10/100 Mbps port used to access the
EdgeSwitch Configuration Interface.
Ports 1-8 10/100/1000 Mbps ports for switching and
PoE (also available for management by
default).
USB Reserved for future use.
Reset
To reset to factory defaults, press and hold
the Reset button for more than 10 seconds
while the unit is already powered on.
Back Panel
Power Power
Ventilation HolesVentilation Holes
Note: There are additional ventilation holes on the top
and sides of the EdgeSwitch.
Front Panel LEDs
Power/Link
PoE
Speed/Link/Act
LED State Status
MGMT
Power/
Link
Off No Power/No Link
Amber
After bootup, the LED indicates
power. After an initial link is
established, the LED indicates a
10/100 Mbps connection. If the link
terminates, the LED turns off until
a link is re-established. If the unit
reboots, the LED will again indicate
power until a link is established.
Ports 1-8
PoE
Off No Power over Ethernet
Green 24V Power over Ethernet
Amber 48V Power over Ethernet
Speed/
Link/
Act
Off No link
Amber Link established at 10/100 Mbps
Amber
Flashing Link activity at 10/100 Mbps
Green Link established at 1000 Mbps
Green
Flashing Link activity at 1000 Mbps
Installation Requirements
• Phillips and flathead screwdrivers
• Standard-sized, 19" wide rack with an available 1U space
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
powersupply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
IMPORTANT: Although the cabling can be located
outdoors, the EdgeSwitch itself should be housed
inside a protective enclosure.
WARNING: To reduce the risk of fire or electric shock,
do not expose this EdgeSwitch to rain or moisture.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Hardware Installation
1. Remove the faceplate from the EdgeSwitch by lifting up
the bottom portion of the faceplate.
2. Connect the Power Cord to the Power port of each
EdgeSwitch.
3. Attach the EdgeSwitch 16XP to the rack using the four
Phillips Screws. (If the rack has square slots, then use the
Cage Nuts with the Phillips Screws.)
4. Attach the top portion of the faceplate at a slight angle,
and then snap on the bottom portion. Secure the faceplate
to the EdgeSwitch 16XP using the two FlatheadScrews.
5. Connect the other end of each Power Cord to a power
outlet.
Daisy-Chain (Optional)
All data ports are available as uplink ports. If you want to
daisy-chain EdgeSwitch A and B, we recommend that you
connect an Ethernet cable from port 8 of EdgeSwitch A to
port1 of EdgeSwitch B.
Note: PoE is disabled by default on all numbered
ports and is not available on the Management port. To
enable PoE on the appropriate ports, use the Ports tab
in the Configuration Interface.
Accessing the Configuration Interface
Connect to the Configuration Interface by performing the
following steps:
1. Ensure that your computer is connected to the
Management port on the EdgeSwitch.
Note: By default, you can configure the EdgeSwitch
via any port; however, we recommend the
Management port. (Access to the Configuration
Interface can be limited to the Management
port only. You can configure this setting on the
Devicetab.)
2. Configure the Ethernet adapter on your computer with a
static IP address on the 192.168.1.x subnet
(e.g., 192.168.1.100).
3. Launch your web browser. Type https://192.168.1.20 in
the address field. Press enter (PC) or return (Mac).
https://192.168.1.20
4. The login screen will appear. Enter ubnt in the Username
and Password fields. Click Login.
The Configuration Interface will appear, allowing you to
customize your settings as needed.
You can also manage your device using the Ubiquiti® Network
Management System. UNMS™lets you configure, monitor,
upgrade, and back up your devices using a singleapplication.
*640-00056-04*
640-00056-04
Configuring PoE Settings
WARNING: Before activating PoE, ensure that the
connected device supports passive PoE and the
supplied voltage. By default, PoE is off on each port.
1. Click the Ports tab.
2. On the Ports tab, select the Ethernet port you want to
configure. Select the appropriate PoE Status setting, and
then click Save Changes.
The PoE LED on the Ethernet port will confirm the PoE setting.
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Ubiquiti Changer
Ubiquiti
Ubiquiti UniFi US-24-250W Manuel utilisateur
Ubiquiti
Ubiquiti UniFi USW-Pro-24-POE Manuel utilisateur
Ubiquiti
Ubiquiti EdgeSwitch 10 XP Manuel utilisateur
Ubiquiti
Ubiquiti UniFi USW-Pro-24-POE Manuel utilisateur
Ubiquiti
Ubiquiti EdgeSwitch ES-10XP Mode d’emploi
Ubiquiti
Ubiquiti FiberPoE Manuel utilisateur
Ubiquiti
Ubiquiti POE-50-60W Manuel utilisateur
Ubiquiti
Ubiquiti ES-48-500W Manuel utilisateur
Ubiquiti
Ubiquiti TouchSwitch Poe TS-5-POE Manuel utilisateur
Ubiquiti
Ubiquiti UniFi USW-16-POE Manuel utilisateur
Ubiquiti
Ubiquiti USW-48-POE Manuel utilisateur
Ubiquiti
Ubiquiti unifi switch 8 Manuel utilisateur
Ubiquiti
Ubiquiti EdgeSwitch 48 LITE Manuel utilisateur
Ubiquiti
Ubiquiti UniFi USW-Industrial Manuel utilisateur
Ubiquiti
Ubiquiti EdgeSwitch 16 XG Manuel utilisateur
Ubiquiti
Ubiquiti UnFi US-48-500W Manuel utilisateur
Ubiquiti
Ubiquiti EdgeSwitch 5XP Manuel utilisateur
Ubiquiti
Ubiquiti ES-24-250W Manuel utilisateur
Ubiquiti
Ubiquiti ES-24-250W Mode d’emploi
Ubiquiti
Ubiquiti USW-Industrial Manuel utilisateur
