TSI Instruments 4040 Manuel d'utilisation

Model 4040/4043/4045

General Purpose

Thermal Mass Flowmeter

Operation and Service Manual

1980339, Revision E

November 2002

Mass Flowmeters

TSI Model 4040/4043/4045

General Purpose

Thermal Mass Flowmeter

Operation and Service

Manual

November 2002

P/N 1980339

Revision E

MAIL/SHIP TO: E-mail address:

TSI Incorporated Flowmeters@tsi.com

500 Cardigan Road

Shoreview, MN 55126-3996 Web site:

USA http://www.tsi.com

U.S. INTERNATIONAL

Sales and Customer Service: Sales and Customer Service:

800-874-2811 or 651-490-2811 (1) 651-490-2811

Fax: Fax:

651-490-3824 (1) 651-490-3824

Address

TSI Incorporated / 500 Cardigan Road / Shoreview, MN 55126 USA

WARNING

These flowmeters employ a heated platinum sensor.

They should not be used with flammable or explosive

gases or mixtures.

Caution

TSI flowmeters are not medical devices under FDA

510k and in no situation should they be utilized for

human respiration measurements.

LIMITATION OF WARRANTY AND LIABILITY (effective July 2000)

Seller warrants the goods sold hereunder, under normal use and service as described in the operator's

manual, shall be free from defects in workmanship and material for twelve (12) months, or the length

of time specified in the operator's manual, from the date of shipment to the customer. This warranty

period is inclusive of any statutory warranty. This limited warranty is subject to the following

exclusions:

a. Hot-wire or hot-film sensors used with research anemometers, and certain other components

when indicated in specifications, are warranted for 90 days from the date of shipment.

b. Parts repaired or replaced as a result of repair services are warranted to be free from defects in

workmanship and material, under normal use, for 90 days from the date of shipment.

c. Seller does not provide any warranty on finished goods manufactured by others or on any fuses,

batteries or other consumable materials. Only the original manufacturer's warranty applies.

d. Unless specifically authorized in a separate writing by Seller, Seller makes no warranty with

respect to, and shall have no liability in connection with, goods which are incorporated into other

products or equipment, or which are modified by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS stated herein.

NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR

PURPOSE OR MERCHANTABILITY IS MADE.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR

BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES, INJURIES,

OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED ON CONTRACT,

NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL BE THE RETURN OF

GOODS TO SELLER AND THE REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION

OF SELLER, THE REPAIR OR REPLACEMENT OF THE GOODS. IN NO EVENT SHALL

SELLER BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES.

SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR

REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be brought against

Seller more than 12 months after a cause of action has accrued. The goods returned under warranty to

Seller's factory shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss.

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND

LIABILITY, which contains the complete and exclusive limited warranty of Seller. This

LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or its terms

waived, except by writing signed by an Officer of Seller.

Service Policy

Knowing that inoperative or defective instruments are as detrimental to TSI as they are to our

customers, our service policy is designed to give prompt attention to any problems. If any malfunction

is discovered, please call TSI's Customer Service department at +1 651 490-2811.

CONTENTS

Chapters

1. UNPACKING AND PARTS IDENTIFICATION..................... 1

2. SETTING-UP......................................................................... 3

Supplying Power.................................................................... 3

Connecting Filter and Flow Tubes......................................... 4

RS232 Configuration and Operation ..................................... 4

Configuration Software.......................................................... 5

3. OPERATION ......................................................................... 7

Overview................................................................................ 7

ON/OFF Switch ..................................................................... 7

Flowrate Measurement.......................................................... 7

Temperature Measurement................................................... 8

Pressure Measurement ......................................................... 8

Volume Measurement ........................................................... 8

4. MAINTENANCE .................................................................... 9

Flow Sensor........................................................................... 9

Re-certification....................................................................... 9

Cases .................................................................................... 9

Storage .................................................................................. 9

5. TROUBLESHOOTING........................................................ 11

APPENDIXES

A. SPECIFICATIONS .............................................................. 13

B. STANDARD FLOWRATE VS.

VOLUMETRIC FLOWRATE ............................................... 17

Chapter 1

Unpacking and Parts Identification

Carefully unpack the instrument and accessories from the shipping container.

Check the individual parts against the list of components in Table 1. If any

parts are missing or damaged, notify TSI immediately.

Table 1. List of Components

Item Descri

tion Part/Model

1 Mass Flowmeter, 22 mm ISO tapered inlet/outlet

Mass Flowmeter, 0.50 inch inlet/outlet

Mass Flowmeter, 0.75 inch inlet/outlet

4040

4043

4045

1 Com

uter Cable 1303583

1 Analo

Cable 1303584

1 Filter

22 mm ISO-taper (for Model 4040)

3/8” Female NPT (for Model 4043/45)

1602292

1602300

1 AC Adapter

120 V, North America, ungrounded

100-240 V, NEMA 5-15 plug, grounded

100-240 V, Europlug, CEE 7/16, grounded

100-240 V, Great Britain, grounded, fused

100-240 V, Australia/NZ

2613033FLO

8918-NA

8918-EC

8918-GB

8918-AT

1 O

eration and Service Manual 1980339

1 RS232 Serial Command Set manual 1980340

1 Carr

Case

(

tional accessor

1319176

Chapter 1

Parts Identification

Figure 1-1 Model 4040/4043/4045 Mass Flowmeter

1. On/Off Switch 4. DC Power Input

2. Display 5. Flow Inlet

3. Mounting Inserts (2) 6. Computer Serial Interface and

Analog Output and Optional

Power Input Connector

Chapter 2

Setting-Up

Supplying Power

The flowmeter can be powered in one of two ways: through the power jack

using the supplied AC adapter or through the mini-DIN connector. The DC

power input connector is shown below along with the power requirements.

Power Supply: 7.5 VDC ±1.5 V, 300 mA maximum

When supplying power through the TSI-supplied interface cable, line up the

arrow on the connector with the bottom side of the flowmeter. Flowmeter

connector pin-out designations are shown below.

Table 2. List of Connector Pin-outs and Cable Color

Code Designations

Pin Function Cable Color Code

1 Power Input (+) Black

2 Power Ground

(

)

Green

3 Analo

Out

(

)

Red

4 Analo

Ground

(

)

Brown

5 (no connection) Blue

6 RS232 Receive

(

)

White

7 RS232 Transmit

(

out

)

Yellow

8 Lo

ic Groun

Gra

Chapter 2

Connecting Filter and Flow Tubes

The Models 4040/4043/4045 have an exposed thermal flow sensor, which

must be protected from foreign matter and particles in the gas flow. TSI has

supplied a filter, which should be connected to the inlet of the flowmeter,

however, any filter will work as long as it has a minimum efficiency of

99.9%.

Caution

Always use a filter on inlet of flowmeter. Failure to

filter the gas flow may change the calibration and/or

permanently damage the sensor.

Note: Flow direction is identified by the large arrow printed on the

bottom side of the flowmeter.

After attaching the filter, connect the flow tube, to the inlet, of the filter.

Connecting a tube to the outlet of the flowmeter will create back pressure.

See Appendix A for flowmeter accuracy specifications when operating at

various pressures. In general, minimize back pressure on the flowmeter to

maintain higher accuracy.

RS232 Configuration and Operation

Many flowmeter operating parameters can be easily configured through the

RS232 serial port. Likewise, the flowrate, temperature, pressure, and

volume can be read through the serial port. Refer to the Series 4000/4100

RS232 Serial Command Set manual for a detailed description of the

commands and command syntax.

RS232 Settings: Baud Rate........ 38.4 k

Data Bits .......... 8

Parity................ None

Stop Bits .......... 1

Flow Control..... None

Table 3. Changeable Operating Parameters

Function Command

Select Gas Calibration (air, oxygen, mixture) SG

Select Ox

en Concentration in Air

(

21% to 99%

)

SGM

Select Standard or Volumetric Flow Measuremen

LCD Display Update Rate (controls averaging) SUR

Select Data U

date Rate for Analo

Out

SSR

Set Analo

Out

ut Full-Scale Flowrate Value SAS

Set Analo

Out

ut Zero Value SAZ

Autres manuels pour 4040

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TSI Instruments Instrument de mesure

TSI Instruments

TSI Instruments DP-CALC 5815 Manuel d'utilisation

TSI Instruments

TSI Instruments VelociCalc Plus 8384 Manuel d'utilisation

TSI Instruments

TSI Instruments questemp 44 Manuel utilisateur

TSI Instruments

TSI Instruments ALNOR 9880 Manuel utilisateur

TSI Instruments

TSI Instruments HM675 Manuel utilisateur

TSI Instruments

TSI Instruments SidePak AM520 Manuel utilisateur

TSI Instruments

TSI Instruments HM675 Instructions d'utilisation et d'entretien

TSI Instruments

TSI Instruments 4040 Manuel d'utilisation

TSI Instruments

TSI Instruments IAQ-CALC 7545 Manuel d'utilisation

TSI Instruments

TSI Instruments 3321 Manuel d'utilisation

TSI Instruments

TSI Instruments 9555 Series Manuel d'utilisation

TSI Instruments

TSI Instruments dusttrak II 8530 Manuel d'utilisation

TSI Instruments

TSI Instruments VelociCalc 9600 Series Manuel d'utilisation

TSI Instruments

TSI Instruments Dickey-John MINI GAC 2500 Manuel utilisateur

TSI Instruments

TSI Instruments Quest Edge 7 Manuel utilisateur

TSI Instruments

TSI Instruments AirAssure Manuel utilisateur

TSI Instruments

TSI Instruments 3936 SMPS Manuel utilisateur

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Manuel utilisateur

TSI Instruments

TSI Instruments VelociCalc 9515-AC Manuel d'utilisation

TSI Instruments

TSI Instruments 3080 Series Manuel d'utilisation

TSI Instruments

TSI Instruments CA-CALC 6203 Series Manuel d'utilisation

TSI Instruments

TSI Instruments VELOCICALC 9565-P-AC Manuel d'utilisation

TSI Instruments

TSI Instruments VelociCalc 9555 Instructions de montage

TSI Instruments

TSI Instruments 4043 Manuel d'utilisation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur