TSI Instruments 3936 SMPS Manuel utilisateur

Model 3936 SMPS

(Scanning Mobility

Particle Sizer)

Instruction Manual

P/N 1933796, Revision G

August 2002

Particle Instruments

SMPS System

Overview

Model 3936 SMPS

(Scanning Mobility

Unpacking the SMPS

System

Particle Sizer) Setting Up SMPS

Hardware

Instruction Manual Operating SMPS

Hardware

Maintaining and

Troubleshooting the

SMPS System

Service 6

Appendixes and

Index

Manual History

The following is a history of the Model 3936 SMPS Scanning

Mobility Particle Sizer Instruction Manual, P/N 1933796.

Revision Date

First printing March 1999

Final April 1999

A November 1999

B April 2000

C May 2000

D July 2000

E July 18, 2000

F February 2001

G August 2002

In Revision A, Table 2-2 was broken down into two tables. The Inlet

Impactor was removed from Table 2-2 and Table 2-3 was created

for the Inlet Impactor. In Table 2-1 Model 3081 Electrostatic

Classifier was changed to read Model 3080 Electrostatic Classifier.

In Revision B, information about and references to the SMPS

software were removed. The SMPS is now supported by a new

version of the Aerosol Instrument Manager®software. Refer to the

Aerosol Instrument Manager®Software for SMPS Instruction Manual,

part number 1930104

In Revision C, Tables B-1 and B-2 were revised.

In Revision D, “Particle Mobility Theory” section in Appendix B was

revised.

In Revision E, TSI’s Limitation of Warranty and Liability was

updated.

In Revision F, page B-12 of Appendix B was revised.

In Revision G, TSI phone numbers were updated, Appendix B was

revised and Table 2-1 and Table 2-2 in Chapter 2.

Part Number 1933796 / Revision G / August 2002

Address TSI Incorporated / 500 Cardigan Road / Shoreview, MN 55126 / USA

Fax No. (651) 490-3824

E-mail Address [email protected]

Limitation of Warranty

and Liability

(effective July 2000)

Seller warrants the goods sold hereunder, under normal use and service as

described in the operator's manual, shall be free from defects in workmanship and

material for twelve (12) months, or the length of time specified in the operator's

manual, from the date of shipment to the customer. This warranty period is

inclusive of any statutory warranty. This limited warranty is sub

ect to the following

exclusions:

a. Hot-wire or hot-film sensors used with research anemometers, and certain other

components when indicated in specifications, are warranted for 90 days from

the date of shipment.

b. Parts repaired or replaced as a result of repair services are warranted to be free

from defects in workmanship and material, under normal use, for 90 days from

the date of shipment.

c. Seller does not provide any warranty on finished goods manufactured by others

or on any fuses, batteries or other consumable materials. Only the original

manufacturer's warranty applies.

d. Unless specifically authorized in a separate writing by Seller, Seller makes no

warranty with respect to, and shall have no liability in connection with, goods

which are incorporated into other products or equipment, or which are modified

by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS

stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR

PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER

OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES,

INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED

ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL

BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE

PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE

GOODS. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES. SELLER SHALL NOT BE

RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS

OR CHARGES. No Action, regardless of form, may be brought against Seller more

than 12 months after a cause of action has accrued. The goods returned under

warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, if at

all, at Seller's risk of loss.

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY

AND LIABILITY, which contains the complete and exclusive limited warranty of

Seller. This LIMITATION OF WARRANTY AND LIABILITY may not be amended,

modified or its terms waived, except by writing signed by an Officer of Seller.

Service Policy Knowing that inoperative or defective instruments are as detrimental to TSI as they

are to our customers, our service policy is designed to give prompt attention to any

problems. If any malfunction is discovered, please contact your nearest sales office

or representative, or call TSI at 1-800-874-2811 (USA) or (651) 490-2811.

Software License

(effective March 1999)

1. GRANT OF LICENSE. TSI grants to you the right to use one copy of the

enclosed TSI software program (the “SOFTWARE”), on a single computer. You may

not network the SOFTWARE or otherwise use it on more than one computer or

computer terminal at the same time.

2. COPYRIGHT. The SOFTWARE is owned by TSI and is protected by United

States copyright laws and international treaty provisions. Therefore, you must

treat the SOFTWARE like any other copyrighted material (e.g., a book or musical

recording) except that you may either (a) make one copy of the SOFTWARE solely

for backup or archival purposes, or (b) transfer the SOFTWARE to a single hard

disk provided you keep the original solely for backup or archival purposes.

3. OTHER RESTRICTIONS. You may not rent or lease the SOFTWARE, but you

may transfer the SOFTWARE and accompanying written material on a permanent

basis, provided you retain no copies and the recipient agrees to the terms of this

Agreement. You may not reverse-engineer, decompile, or disassemble the

SOFTWARE.

4. DUAL MEDIA SOFTWARE. If the SOFTWARE package contains multiple types

of media, then you may use only the media appropriate for your single-user

computer. You may not use the other media on another computer or loan, rent,

lease, or transfer them to another user except as part of the permanent transfer

(as provided above) of all SOFTWARE and written material.

5. U.S. GOVERNMENT RESTRICTED RIGHTS. The SOFTWARE and

documentation are provided with RESTRICTED RIGHTS. Use, duplication, or

disclosure by the Government is subject to the restrictions set forth in the “Rights

in Technical Data and Computer Software” Clause at 252.227-7013 and the

“Commercial Computer Software - Restricted Rights” clause at 52.227-19.

6. LIMITED WARRANTY. TSI warrants that the SOFTWARE will perform

substantially in accordance with the accompanying written materials for a period

of ninety (90) days from the date of receipt.

7. CUSTOMER REMEDIES. TSI’s entire liability and your exclusive remedy shall

be, at TSI’s option, either (a) return of the price paid or (b) repair or replacement of

the SOFTWARE that does not meet this Limited Warranty and which is returned

to TSI with proof of payment. This Limited Warranty is void if failure of the

SOFTWARE has resulted from accident, abuse, or misapplication. Any

replacement SOFTWARE will be warranted for the remainder of the original

warranty period or thirty (30) days, whichever is longer.

8. NO OTHER WARRANTIES. TSI disclaims all other warranties, either express or

implied, including, but not limited to implied warranties of merchantability and

fitness for a particular purpose, with regard to the SOFTWARE and the

accompanying written materials.

9. NO LIABILTY FOR CONSEQUENTIAL DAMAGES. In no event shall TSI be liable

for any damages whatsoever (including, without limitation, special, incidental,

consequential or indirect damages for personal injury, loss of business profits,

business interruption, loss of information or any other pecuniary loss) arising out

of the use of, or inability to use, this SOFTWARE.

Trademarks Microsoft is a registered trademark of Microsoft Corporation.

Windows is a trademark of Microsoft Corporation.

IBM is a registered trademark of International Business Machines Corporation.

Acknowledgments TSI Incorporated acknowledges the significant contributions of Richard C. Flagan of

the California Institute of Technology and Kevin Horton of AEA Technology for their

research and support in developing SMPS system software.

Safety

vii

This section gives instructions to promote safe and proper

operation of the Model 3936 Scanning Mobility Particle Sizer (SMPS

system), samples of warnings found in this manual, and

information on labels attached to system instruments.

Laser Safety

The Model 3936 Scanning Mobility Particle Sizer and Model 3010,

3022/3022A, and 3025/3025A Condensation Particle Counters

(CPC) are Class I laser-based instrument. During normal operation,

you will not be exposed to laser radiation. However, you must take

certain precautions or you may expose yourself to hazardous,

optical radiation in the form of intense, focused, invisible light.

Exposure to this light can cause blindness.

Take these precautions:

 Do not remove any parts from SMPS system instruments unless

you are specifically told to do so in this manual.

Do not remove any instrument housing when power is applied.

WARNING

The use of controls, adjustments, or procedures other than those

specified in this manual may result in exposure to hazardous optical

radiation.

Electrical Safety

The Model 3080 Classifier; Models 3010, 3022, 3022A, 3025, and

3025A CPCs; and Model 3081, 3083, and 3085 DMAs have high-

voltage points within their cabinets/cases. Only a qualified

technician should perform service or maintenance.

viii Model 3936 SMPS (Scanning Mobility Particle Sizer)

WARNING

High voltage is accessible in several locations within these instruments.

Make sure you unplug the power source before removing the cover or

performing maintenance procedures. Don’t apply power to the

Model 3080 Classifier unless you have a DMA high-voltage cord

connected and the DMA properly grounded through the baseplate.

Chemical Safety

CPCs use n-butyl alcohol (butanol) as a working fluid. Butanol is

flammable. Butanol is also toxic if inhaled. Refer to a material

safety data sheet on butanol and take these precautions:

Use butanol only in a well-ventilated area.

Butanol vapor is identified by its characteristically strong odor

and can easily be detected. If you smell butanol and develop a

headache, or feel faint or nauseous, leave the area at once.

Ventilate the area before returning.

Caution

Butanol is flammable. Butanol is also potentially toxic if inhaled. Use

butanol only in a well-ventilated area. If you smell butanol and

develop a headache, or feel faint or nauseous, leave the area at

once. Ventilate the area before returning.

WARNING

Although the CPC is appropriate for monitoring inert process gases such

as nitrogen or argon, it should not be used with hazardous gases such

as hydrogen or oxygen. Using the CPC with hazardous gases may

cause injury to personnel and damage to equipment.

Safety ix

Radiation Safety

The Model 3080 Electrostatic Classifier contains a Model 3077

Aerosol Neutralizer with a Krypton-85 source. Under normal

circumstances, you will not come into contact with hazardous

radiation. However, take these precautions when using the

Neutralizer in an Electrostatic Classifier or in another instrument:

Do not remove any parts from the Electrostatic Classifier unless

you are specifically told to do so in the Electrostatic Classifier

manual.

Corrosive materials can degrade materials that are a part of the

Neutralizer. Do not operate the Classifier or other instrument

with chemicals that corrode 303, 304, or 316 stainless steel,

copper, silver solder, or epoxy.

Do not operate the Electrostatic Classifier or other instrument

in temperatures above 50°C. Temperatures above 50°C may

cause the Neutralizer to leak, causing radioactive

contamination.

The Neutralizer has a half-life of 10.4 years. Keep all Neutralizer

packing materials. After 10 years, TSI recommends you return

the Neutralizer to the manufacturer and order a new

Neutralizer.

Install and remove the Neutralizer using directions in

Electrostatic Classifier manual (if applicable).

WARNING

The use of controls, adjustments, or procedures other than those

specified in this manual may result in exposure to hazardous radiation.

Labels

External and internal advisory labels and identification labels are

attached to the CPC, the Aerosol Neutralizer, and the Electrostatic

Classifier. Refer to individual product manuals for descriptions and

locations of these labels.

x Model 3936 SMPS (Scanning Mobility Particle Sizer)

Table des matières

Autres manuels TSI Instruments Instrument de mesure

TSI Instruments

TSI Instruments HM685 Manuel utilisateur

TSI Instruments

TSI Instruments DUSTTRAK 854201-M1 Manuel utilisateur

TSI Instruments

TSI Instruments 3321 Manuel d'utilisation

TSI Instruments

TSI Instruments 4000 Series Mode d’emploi

TSI Instruments

TSI Instruments DP-CALC 5825-AC Manuel d'utilisation

TSI Instruments

TSI Instruments Alnor Model AXD620 Manuel d'utilisation

TSI Instruments

TSI Instruments 9535A Manuel d'utilisation

TSI Instruments

TSI Instruments SidePak AM520 Manuel utilisateur

TSI Instruments

TSI Instruments Aerotrak 9303 Manuel utilisateur

TSI Instruments

TSI Instruments Alnor AirGard 405 Manuel utilisateur

TSI Instruments

TSI Instruments VelociCalc 9555 Instructions de montage

TSI Instruments

TSI Instruments VELOCICALC 9565-P-AC Manuel d'utilisation

TSI Instruments

TSI Instruments VELOCICALC 9515 Manuel d'utilisation

TSI Instruments

TSI Instruments VELOCICALC 5725 Manuel d'utilisation

TSI Instruments

TSI Instruments HM675 Instructions d'utilisation et d'entretien

TSI Instruments

TSI Instruments 3080 Series Manuel d'utilisation

TSI Instruments

TSI Instruments HM685 Manuel utilisateur

TSI Instruments

TSI Instruments 9600 Series Manuel d'utilisation

TSI Instruments

TSI Instruments DustTrak DRX Manuel utilisateur

TSI Instruments

TSI Instruments 8495 Manuel d'utilisation

TSI Instruments

TSI Instruments DP-CALC 5825 Manuel d'utilisation

TSI Instruments

TSI Instruments Alnor Airflow AXD610 Manuel d'utilisation

TSI Instruments

TSI Instruments 4040 Manuel d'utilisation

TSI Instruments

TSI Instruments Quest Edge 7 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur