TSI Instruments VelociCalc 9555 Instructions de montage

135 Bernice Drive, Bensenville IL 60106-3366

Toll Free (866)736-8347 Phone (815)464-6200

Fax (815)464-8720

www.raecorents.com

Nationwide rental of industrial hygiene and safety instrumentation, from a service that treats you right.

©2014 RAECO Rents LLC, Bensenville IL. All rights reserved.

TSI VelociCalc 9555/9565 Quick Tips for Pressure Testing

For complete documentation, see http://mobibrix.com/0DKVGG

1. Probe Sampling

a. Connect probe to bottom of instrument, and turn

the instrument on

b. To change the readings displayed on screen...

1. Select [Menu] softkey

2. Select Display Setup

3. Use the softkeys to select display values

(Primary sets value to a larger font to make it

more visible to the user)

a. 964 probe – Flow, Temperature, and %rH set to ON

b. 982 Probe – CO, CO2, Temperature and %rh set to ON

c. 985 Probe – VOC and Temperature set to ON

d. 995 Probe – Flow and Temperature set to ON

4. Press [Enter] to save changes.

c. Set up data logging values

1. Select [Menu] softkey

2. Select Data Logging

3. Select Measurements

4. Select values to be logged by instrument

a. ON = Measurement is logged to memory

b. Display = Measurement will be logged if it is displayed on the main screen

c. OFF = Unit will not save data for that value

d. Hold probe to take samples

e. [NEXT TEST] key saves data up to the point it is pressed and begins a new session

135 Bernice Drive, Bensenville IL 60106-3366

Toll Free (866)736-8347 Phone (815)464-6200

Fax (815)464-8720

www.raecorents.com

Nationwide rental of industrial hygiene and safety instrumentation, from a service that treats you right.

©2014 RAECO Rents LLC, Bensenville IL. All rights reserved.

2. Differential Pressure Testing

a. Connect the two lengths of neoprene tubing to the positive and

negative ports at the top of the instrument

b. Place the free end of the positive port tubing in the area being

tested

c. Place the free end of the negative port tubing in the control/ambient zone

1. A positive reading means the variable/sample (+)zone is higher pressure than the

control/ambient (-)

2. A negative reading means the control/ambient zone (-) is higher pressure than the

variable/sample (+)zone

3. Static Pressure Testing

a. Connect one length of neoprene tubing to the positive port at the top of the instrument

b. Keep the negative (-) port open to measure ambient conditions

c. Attach the static pressure tip to the tubing on the positive (+)port

d. Point the static pressure tip directly into airflow to get an accurate reading

1. Positive reading means the pressure in the duct is higher than the measured ambient

conditions

2. Negative reading means the pressure in the duct is lower than the measured ambient

conditions

For complete documentation, see http://mobibrix.com/0DKVGG

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels TSI Instruments Instrument de mesure

TSI Instruments

TSI Instruments CA-CALC 6203 Series Manuel d'utilisation

TSI Instruments

TSI Instruments 4040 Manuel d'utilisation

TSI Instruments

TSI Instruments Alnor Airflow AXD610 Manuel d'utilisation

TSI Instruments

TSI Instruments Q-TRAK XP 7585 Manuel utilisateur

TSI Instruments

TSI Instruments 9565-P Manuel d'utilisation

TSI Instruments

TSI Instruments 4000 Series Mode d’emploi

TSI Instruments

TSI Instruments SIZER 3321 Manuel utilisateur

TSI Instruments

TSI Instruments Airflow TA500 Series Manuel d'utilisation

TSI Instruments

TSI Instruments 3936 SMPS Manuel utilisateur

TSI Instruments

TSI Instruments DustTrak 8540 Manuel d'utilisation

TSI Instruments

TSI Instruments 4040 Manuel d'utilisation

TSI Instruments

TSI Instruments 5300 Series Guide de configuration

TSI Instruments

TSI Instruments Q-Trak XP Manuel d'utilisation

TSI Instruments

TSI Instruments DustTrak DRX Manuel utilisateur

TSI Instruments

TSI Instruments VELOCICALC 9565 Series Manuel d'utilisation

TSI Instruments

TSI Instruments dusttrak II 8530 Manuel d'utilisation

TSI Instruments

TSI Instruments IAQ-CALC 7545 Manuel d'utilisation

TSI Instruments

TSI Instruments 5300 Series Manuel utilisateur

TSI Instruments

TSI Instruments IAQ50 Manuel utilisateur

TSI Instruments

TSI Instruments DP-CALC 5825 Manuel d'utilisation

TSI Instruments

TSI Instruments 5200 Series Manuel utilisateur

TSI Instruments

TSI Instruments AIRASSURE 8144 Manuel utilisateur

TSI Instruments

TSI Instruments DP-CALC 5815 Manuel d'utilisation

TSI Instruments

TSI Instruments 8495 Manuel d'utilisation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur