TSI Instruments HM685 Manuel utilisateur

HM685 QUICK START GUIDE

Key Pad

Each key and its function are described below.

▲▼

The ▲and ▼keys are used to navigate through menus or to select an item to change.

◄►

The ◄ and ► keys are used to change the selected item.

ESC

The ESC key returns to the previous screen or cancels an operation without saving changes.

Pressing the ENTER key accesses the Main Menu, select a menu item or accept changes.

READ

Pressing the READ key initiates taking a time-averaged reading based on Log Mode and Log

Settings. After taking the reading, the values are stored to memory (current Test ID) and displayed

on screen for a period of four (4) seconds or until the READ key has been pressed again. The

READ key also updates the calculations with current readings in the CALCULATIONS Menu.

Press the BACKLIGHT key to turn the display’s backlighting on or off.

DATA

Press the DATA key from a measurement screen to access the Data Logging Menu.

PRESS

Accesses the Pressure measurement screen from the Flow measurement screen.

Press the key to turn the HM685 Hydronic Manometer on or off.

CALC

Accesses the Calculations menu from the Flow or Pressure measurement screen.

FLOW

Accesses the Flow measurement screen form the Pressure measurement screen.

Instrument Power

The HM685 Hydronic Manometer can be powered by four (4) AA-size batteries (alkaline or rechargeable NiMH)

or the AC adapter.

Battery Installation

Locate the battery cover on the back of the unit and loosen the screw to remove. Take out the battery holder and

replace with fresh batteries (alkaline or rechargeable NiMH). Ensure that the batteries are correctly oriented within

the battery holder and Set the battery-type selection switch to indicate the type of batteries to be used (alkaline or

rechargeable NiMH). Reinstall the battery holder and battery cover.

Using the AC Adapter

The AC adapter allows the HM685 Hydronic Manometer to be powered from a standard AC wall outlet. When

using the AC adapter, alkaline batteries (if installed) will be bypassed. The AC adapter also charges the NiMH

type batteries (if installed) in the unit.

Zeroing the Gauge Pressure Sensor

Upon instrument start-up, the user will be prompted to zero the gauge pressure sensor and includes on-screen

instructions. Gauge pressure sensor zeroing can also be initiated by selecting Zero Gauge Pressure when in the

Main Menu by pressing the ENTER ( ) key. The (+) and (-) pressure ports must be open to atmosphere and

the valve handle on the manometer set to the MEASURE position.

netzerotools.com

TSI Alnor HM685 Hydronic Manometer

-2-

Zeroing the Differential Pressure Sensor

Turn the valve handle on the manometer to the BYPASS position while in the main Measurement Screen to

automatically zero the differential pressure sensor. Zeroing of the differential pressure sensor occurs any time the

valve handle is turned to the BYPASS position. Any pressures applied to the hoses will not affect the dP zeroing

function and allows for zeroing of the differential pressure sensor while maintaining connections to the system

under test.

Attaching the Hoses to the Manometer

Connect the straight female flare fitting on the High pressure (red) hose to the male fitting on the top of the

manometer marked with a plus (+) sign. Connect the straight female flare fitting on the Low pressure (blue) hose

to the male fitting on the top of the manometer marked with a minus (-) sign.

Bleeding Entrained Air from the Hoses

1. Turn the shut-off ball valve on both the High and Low pressure hoses to the closed position.

2. Turn the valve handle on the manometer to the MEASURE position.

3. Using an appropriate fitting, connect the open end of the High pressure (red) hose to the test point with the

higher line pressure.

4. Attach the appropriate fitting to the open end of the Low pressure (blue) hose.

5. To ensure all the air is bled from the hoses, hold the open end of the Low pressure (blue) hose in an upright

position over a suitable receptacle or near a drain.

6. Turn the shut-off ball valve on both the High and Low pressure hoses to the open position.

7. Turn the valve handle on the manometer to the BYPASS position to allow the liquid flow to displace the

entrained air.

8. Once the liquid is flowing steadily from the Low pressure (blue) hose, turn the valve handle on the manometer

to the MEASURE position.

Performing Pressure Measurements

The HM685 Hydronic Manometer allows for simultaneous and continuous measurement and display of the High-

side gauge and Differential pressure. The calculated Low-side gauge pressure is also displayed.

Discrete Pressure Measurements

Taking a discrete pressure measurement allows for measurement and display of a single time-averaged reading

taken over the sampling period as defined by the Log Mode and Log Settings. Discrete measurement values are

stored to the memory (current Test ID) and displayed on-screen for a period of four (4) seconds and then returns

to continuous measurement mode. Press the READ key to initiate.

netzerotools.com

-3-

Performing Flow Measurements

The manometer makes and displays continuous differential pressure measurements, calculates and displays

continuous flow readings, and allows for discrete data storage to the memory when in the Flow measurement

screen.

Flow

A calculated value determined from the differential pressure and user entered values for the

valve flow coefficient (Cv or Kv) and fluid specific gravity.

Cv/Kv

The valve flow coefficient is indicated as Cv (Kv) on the manometer display. The Cv (Kv)

value of the measured valve must be known in order to obtain meaningful flow readings.

Discrete Flow Measurements

Taking a discrete flow measurement allows for measurement and display of a single time-averaged reading taken

over the sampling period as defined by the Log Mode and Log Settings. Discrete pressure or flow measurement

values are stored to the memory (current Test ID) and displayed on-screen for a period of 4 seconds and then

returns to continuous measurement mode. Press the READ key to initiate.

Performing Temperature Measurements

The accessory temperature probes are optional for the HM685 Hydronic Manometer and can be connected to the

3-pin mating connector located on the right-hand side of the manometer. The unit of measurement for

temperature (°F or °C) is driven by the differential pressure measurement:

Differential pressure in psi, inH2O, ftH2O, or inHg → temperature in °F

Differential pressure in kPa, mH2O, mmHg, or bar → temperature in °C

Menu Items

Pressing the key from either the Pressure or Flow Measurement screens accesses

the Main Menu, select a menu item or accept changes. Use the arrow ▲▼ ◄► keys

to navigate through menu items and change selected items.

Flow Setup

Use Flow Setup to set values for key factors that impact measured flow values.

netzerotools.com

Data Logging

Access the Data Logging Menu by pressing the DATA key from either the Pressure or Flow Measurement

screens or from the Main Menu.

Log Mode: HM685 programmable logging formats:

Auto-Save Logging

Samples are automatically logged to memory at the end of the sampling period. To

start logging, press the Read key.

Cont-key Logging

Logging starts by press the Read key. The instrument continues logging until the Esc

key is pressed.

Cont-time Logging

Readings start by pressing the Read key. The instrument continues taking samples

until the time set in “Sample Time” elapses or the Esc key is pressed.

Log Settings: defines the period the manometer will log sample readings. When the Log Mode is set to Cont-

Time, this setting is also used to define the length of the test in hh:mm:ss.

Choose Test: choose the Test where the samples (readings) will be stored.

Name Test: customize the Test ID name of the selected test using 10 characters maximum.

View Data: choose the data to review.

Delete Data: delete discrete samples, an entire Test ID, or all data stored.

Memory: displays the total memory available

Calculations

The Calculations Menu is accessed by pressing the CALC key from either the

Pressure or Flow Measurement screens.

Brake Power: determines pump brake power using flow, delta P and pump efficiency

Heat Flow: determines heat flow using temperature, flow, specific heat and gravity

Calc Cv/Kv: calculates Cv or Kv based on flow and differential pressure

Pump Law Impeller Diameter: allows for determination of required pump

impeller size

Pump Law Delta P: determines required pump pressure drop using flow and delta P inputs

Pump Law Brake Power: determines pump brake power based upon the following affinity law: Pump brake

power varies as the cube of flow

Settings

The Settings menu allows customization of the

instrument display.

netzerotools.com

Autres manuels pour HM685

Table des matières

Autres manuels TSI Instruments Instrument de mesure

TSI Instruments

TSI Instruments 3080 Series Manuel d'utilisation

TSI Instruments

TSI Instruments Alnor RVA801 Manuel d'utilisation

TSI Instruments

TSI Instruments 3082 Manuel utilisateur

TSI Instruments

TSI Instruments Aerotrak 9303 Manuel utilisateur

TSI Instruments

TSI Instruments Alnor AirGard 405 Manuel utilisateur

TSI Instruments

TSI Instruments ALNOR AVM430A Manuel d'utilisation

TSI Instruments

TSI Instruments Dickey-John MINI GAC 2500 Manuel utilisateur

TSI Instruments

TSI Instruments TF Series Manuel utilisateur

TSI Instruments

TSI Instruments 5200 Series Manuel utilisateur

TSI Instruments

TSI Instruments Sizer 3310A Manuel utilisateur

TSI Instruments

TSI Instruments ALNOR AXD 530 Manuel utilisateur

TSI Instruments

TSI Instruments VelociCalc 9545 Manuel d'utilisation

TSI Instruments

TSI Instruments Quest Edge 7 Manuel utilisateur

TSI Instruments

TSI Instruments Q-Trak XP Manuel d'utilisation

TSI Instruments

TSI Instruments ALNOR 9880 Manuel utilisateur

TSI Instruments

TSI Instruments Cheetah CH-5 Manuel utilisateur

TSI Instruments

TSI Instruments EG4 Manuel utilisateur

TSI Instruments

TSI Instruments Flowmaster 250 Mode d’emploi

TSI Instruments

TSI Instruments Quest Edge 7 Manuel utilisateur

TSI Instruments

TSI Instruments 4040 Manuel d'utilisation

TSI Instruments

TSI Instruments 8495 Manuel d'utilisation

TSI Instruments

TSI Instruments 9600 Series Manuel d'utilisation

TSI Instruments

TSI Instruments IAQ50 Manuel utilisateur

TSI Instruments

TSI Instruments 5200 Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur