Tripp Lite SmartOnline SUINT1000XLCD Manuel utilisateur

Owner’s Manual

SmartOnline®

True On-Line Single-Phase UPS Systems

with Pure Sine Wave Output

Models: SUINT1000XLCD, SUINT2000XLCD, SUINT3000XLCD

Input: 220/230/240V

Español 25 • Français 49 • Русский 73 • Deutsch 97

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-09-252-93358B.indb 1 1/9/2019 2:19:26 PM

Table of Contents

1. Important Safety Warnings.................. 3

1.1 UPS Location Warnings................... 3

1.2 UPS Connection Warnings............... 3

1.3 Equipment Connections Warnings.... 3

1.4 Battery Warnings............................ 3

1.5 Standard Compliance ..................... 4

1.6 Storage......................................... 4

2. Introduction........................................5

2.1 General Overview ........................... 5

2.2 Exterior & Dimensions..................... 5

2.3 Package Contents .......................... 6

3. Operation Panel..................................7

3.1 LED Indicators ............................... 7

3.2 Multi-function Buttons .................... 7

3.3 LCD Display................................... 8

3.4 7-Segment Display....................... 10

3.5 Flow Chart of the

7-Segment Display....................... 11

4. Rear Panel........................................13

5. Operation Modes ..............................14

5.1 Standby Mode ............................. 14

5.2 On-line Mode............................... 14

5.3 Bypass Mode............................... 14

5.4 Economy Mode............................ 14

5.5 Battery Mode............................... 14

5.6 Setup Mode ................................ 15

5.7 External Battery Type

Selection Mode............................ 17

6. Turn-on, Cold Start &

Turn-off Procedures ..........................18

6.1 Turn-on Procedures ...................... 18

6.2 Cold Start Procedures................... 18

6.3 Turn-off Procedures ...................... 18

7. Alarm................................................ 18

8. Optional Accessories ........................19

8.1 Additional Power Management

Features ...................................... 19

9. Troubleshooting ................................20

10. Maintenance.....................................21

10.1 Maintenance Safety Warnings ...... 21

10.2 UPS........................................... 22

10.3 Batteries .................................... 22

10.4 Recycling the Used Battery........... 22

11. Technical Speciﬁcations.................... 23

12. Regulatory Compliance .....................24

18-09-252-93358B.indb 2 1/9/2019 2:19:26 PM

1. Important Safety Warnings

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed

these warnings may affect your warranty.

1.1 UPS Location Warnings

Install the UPS system indoors, away from excess moisture or heat, conductive contaminants, dust

or direct sunlight.

• Maintain the indoor temperature between 0° C and 40° C.

• Leave adequate space around all sides of the UPS for proper ventilation.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, causing product damage not covered under

warranty.

1.2 UPS Connection Warnings

• Connect the UPS directly to a properly grounded AC power outlet. Do not plug the UPS into itself;

this will damage the UPS.

• Do not modify the UPS system’s plug and do not use an adapter that would eliminate the UPS

system’s ground connection.

• Do not use extension cords to connect the UPS to an AC outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide clean,

ﬁltered, computer-grade output.

• Power cables should not exceed 10 m.

1.3 Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to signiﬁcantly affect its safety

or effectiveness is not recommended. Do not use this equipment in the presence of a ﬂammable

anesthetic mixture with air, oxygen or nitrous oxide.

• The UPS system contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

1.4 Battery Warnings

UPS Rating Built-in Batteries Battery Qty. Battery Type Battery Voltage

1kVA

Yes

29 Ah Sealed

Lead-Acid Battery

24Vdc

2kVA 4 48Vdc

3kVA 6 72Vdc

• The UPS does not require routine maintenance. Do not open the UPS for any reason. There are

no user-serviceable parts inside.

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Disconnect and turn off the UPS

before performing battery replacement. Use tools with insulated handles. Battery replacement

should be performed only by authorized service personnel using the same number and type of

batteries (Sealed Lead-Acid). The batteries are recyclable. Refer to your local codes for disposal

requirements or visit http://www.tripplite.com/support/recycling-program for recycling information.

Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit

Tripp Lite on the Web at http://www.tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc

replacement battery for your UPS.

18-09-252-93358B.indb 3 1/9/2019 2:19:26 PM

1. Important Safety Warnings

• Connect only Tripp Lite battery modules to the UPS system’s external battery hardware terminals.

• Do not operate the UPS without batteries.

• Fuses should be replaced only by factory authorized personnel. Blown fuses should be replaced

only with fuses of the same number and type.

• Potentially lethal voltages exist within this unit as long as the battery supply is connected. Service

and repair should be done only by trained personnel. During any service work, the UPS should be

turned off or put into manual bypass and fuses removed from all connected battery modules.

• Do not connect or disconnect the battery modules while the UPS is operating from the battery

supply or when the unit is not in bypass mode.

1.5 Standard Compliance

• CE

• EN 62040-1

• EN 62040-2 Category C2

1.6 Storage

Prior to installation

If the UPS needs to be stored prior to installation, it should be placed in a dry area. The allowable

storage temperature is between -15°C and 50°C.

After usage

Press the OFF button, make sure the UPS is shutdown, disconnect the UPS from the utility power,

remove all equipment from the UPS, and store the UPS in a dry and well-ventilated area at a

temperature between -15°C and 50°C. Idle batteries must be recharged fully approximately every

three months if the UPS needs to be stored for an extended period of time. The charging time must

not be less than 24 hours each time.

Note: After storage and before start-up of the UPS, allow the UPS to adjust to room temperature (20° to 25°C) for

at least one hour to avoid moisture condensation inside the UPS.

18-09-252-93358B.indb 4 1/9/2019 2:19:26 PM

2. Introduction

2.1 General Overview

Tripp Lite’s SUINT-Series UPS is a VFI (voltage and frequency independent) true online double

conversion UPS, providing reliable and consistent sine-wave quality power to your electronic

equipment. Designed to the highest quality with modern IGBT technology, the Tripp Lite SUINT-

Series of UPS systems delivers a secure, reliable and uninterrupted supply of clean power to your

critical loads.

Developed with a variety of ratings and a compact footprint, the SUINT-Series delivers a high output

power factor and high operating efﬁciency, providing more actual power to the attached load.

2.2 Exterior & Dimensions

225mm

320mm

145mm

325mm

390mm

190mm

Figure 2-1: SUINT1000XLCD Exterior and Dimensions Figure 2-2: SUINT2000XLCD / SUINT3000XLCD

Exterior and Dimensions

18-09-252-93358B.indb 5 1/9/2019 2:19:26 PM

2. Introduction

2.3 Package Contents

SUINT1000XLCD SUINT2000XLCD /

SUINT3000XLCD

Item SUINT1000XLCD SUINT2000XLCD / SUINT3000XLCD

UPS System 1 Pc. 1 Pc.

Owner's Manual 1 Pc. 1 Pc.

IEC to IEC Jumpers 2 Pc. 3 Pc.

USB Cable 1 Pc. 1 Pc.

RS232 Cable 1 Pc. 1 Pc.

Note:

1. Inspect the UPS system for damage after unpacking it. If there is any damage or anything is missing,

immediately contact Tripp Lite Tech Support.

2. If the UPS needs to be returned, carefully repack the UPS and all of the accessories using the original packing

material that came with the unit. It is recommended to retain all original packing materials.

Model-Speciﬁc Accessories (Optional)*

Model SUINT1000XLCD SUINT2000XLCD SUINT3000XLCD

External Battery Pack (LIMIT 1) BP24V15RT2U or

BP24V28-2U

BP48V24-2U or

BP24V27-2US

BP72V15-2U or

BP72V18-2US

External Battery Pack (NO LIMIT) BP24V70RT3U BP48V60RT3U BP72V28RT3U

* Visit the speciﬁcation page for your UPS system at www.tripplite.com for detailed extended runtime data and

additional accessory options.

EXTERNAL BATTERY CONFIGURATION NOTE

If external battery packs are to be used with this UPS, install them following the mounting/installation

documentation included with each battery pack. External battery pack installation requires the UPS be conﬁgured

via Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software, downloadable from

http://www.tripplite.com/bpconﬁg (for all external runtime conﬁgurations)

This UPS is factory programmed with discharge curves and charging proﬁles for two basic external battery pack

conﬁgurations accessible using the UPS front panel LCD interface. Additional battery pack options using larger or

multiple external battery packs are also supported, but require conﬁguration using Tripp Lite’s EXTERNAL BATTERY

CONFIGURATION software and a serial port connection to the UPS. See 5.7 External Battery Type Selection

Mode to determine which method applies to your external battery pack conﬁguration.

18-09-252-93358B.indb 6 1/9/2019 2:19:26 PM

3. Operation Panel

3.1 LED Indicators

GREEN LED: Indicates the output status.

1. ON (green): Output available

2. OFF: Output unavailable

RED LED:

1. ON: The UPS detects an internal fault or an environmental fault. Refer to 3.3 LCD

Readout for more information.

2. Flashing: The UPS has the following warning message(s):

a. : There is no battery or battery replacement is needed.

b. : The UPS is overloaded.

3.2 Multi-Function Buttons

ON: The button has four functions. Refer to the following for detailed information:

1. Turn-on:

• In standby mode, press and hold the button for 3 seconds. Release it after one

beep. The UPS will run in on-line mode.

• Cold start: When there is no AC input, press and hold the button for 3 seconds.

Release it after one beep. The UPS will start up in battery mode.

2. Battery Test: A battery test may only be executed in on-line mode.

• From manual battery test, press and hold the button for 3 seconds. Release it after

one beep. The UPS will transfer to battery mode and perform a 10-second battery

test.

If the test result is normal, the LCD will show ‘PAS’ and the UPS will return to on-

line mode.

If the test result is abnormal, the LCD will show ‘bAd’, the LED will ﬂash, the

warning icon and no-battery/ battery replacement icon will illuminate. The

UPS will return to on-line mode.

3.1 LED Indicators

3.3 LCD Readout

(including 3.4 7-Segment Display)

3.2 Multi-function Buttons

18-09-252-93358B.indb 7 1/9/2019 2:19:27 PM

3. Alarm Off: When the alarm is on, press the button for 0.1 second to turn the alarm

off. Note that the alarm will turn on automatically when a new alarm occurs.

Note: The alarm cannot be turned on manually after it has been muted in setup.

4. Conﬁrmation: In setup mode, press the button for 0.1 second to conﬁrm parameter

setup.

OFF: The button has two functions. Refer to the following for detailed information:

1. Turn-off:

• In on-line mode, press and hold the button for 3 seconds. Release it after one

beep. The inverter will be off and the UPS will transfer to standby mode.

The UPS will keep charging the batteries in standby mode even though the button

has been pressed. To fully turn off the UPS, it is advised to unplug the input power

cord.

• In battery mode, press and hold the button for 3 seconds. Release it after one

beep. The UPS will turn off its output.

2. Fault Clear:

When the UPS has a fault condition, press and hold the button for 3 seconds.

Release it after one beep. The UPS will clear the fault condition and return to standby

mode. The LCD will show the relevant error code. For error code information, refer to

3.3 LCD Readout.

SETUP: The button has two functions. Refer to the following for detailed information:

1. Scrolling down:

Press the button for 0.1 second to go to the next display.

2. Entering into the setup mode:

Press the button for 3 seconds and the UPS will enter setup mode. For more

information, refer to 5.6 Setup Mode. Please note that only qualiﬁed service

personnel can perform setup actions.

Note: When the backlight of the LCD is off, press any button to wake up the display and enable

each button function.

3.3 LCD

AC Icon: Indicates the input source status.

1. ON: The AC input is within the acceptable input voltage range.

2. Flashing: The AC input is out of the acceptable input voltage range but is still

sufﬁcient to let the unit operate in on-line mode.

3. OFF: The AC input is out of the acceptable input voltage range and is not sufﬁcient to

let the unit operate in on-line mode.

Output Icon: Indicates the output status.

1. ON: Output available.

2. OFF: Output unavailable.

Note: In setup Mode, the LED will be off, but output will still be available.

Battery Power Icon: Indicates the battery power status.

1. ON: On battery.

2. OFF: Output is not supplied by the battery power.

3. Operation Panel

18-09-252-93358B.indb 8 1/9/2019 2:19:27 PM

3. Operation Panel

Standby Mode Graph: Illuminates when the UPS is operating in standby mode.

On-line Mode Graph: Illuminates when the UPS is operating in on-line mode.

Battery Mode Graph: Illuminates when the UPS is operating in battery mode.

Bypass Mode Graph: Illuminates when the UPS is operating in bypass mode.

Alarm Icon: Illuminates when the alarm is disabled.

Warning Icon:

1. ON: The unit is shut down due to an internal or environmental fault. The error code

will appear on the 7-segment display. Refer to the following table for each error code

and refer to 3.4 7-Segment Display for relevant 7-segment display information.

Error Code Meaning

E11 Charger Fault

E13 Temperature Out of Range

E14 +/- DC BUS High/Low

E16 Inverter Fault

E18 DC-DC Fault

E19 Abnormal Output/Inverter Voltage

E21 Output Short Circuit

Sd1 RPO Shutdown

Sd4 Battery Low Shutdown

2. Flashing: When the icon is ﬂashing, it will be accompanied by other icon(s) to show

the corresponding warning message(s).

a. : There is no battery or battery replacement is needed.

b. : The UPS is overloaded.

Load Level Bar Graph: Indicates the load level status.

1. ON: The bar graph illuminates according to the load level *1.

2. Flashing: The bar graph ﬂashes when there is an overload situation.

Battery Level Bar Graph: Indicates the status of battery level.

1. ON: The bar graph illuminates according to the remaining battery capacity *1.

2. Flashing: The bar graph ﬂashes when a low-battery situation occurs.

Note: *1 means that:

<10%: no segment will illuminate.

10-29%: the ﬁrst segment will illuminate.

30-49%: the ﬁrst two segments will illuminate.

50-69%: the ﬁrst three segments will illuminate.

70-89%: the ﬁrst four segments will illuminate.

90-100%: all segments will illuminate.

18-09-252-93358B.indb 9 1/9/2019 2:19:28 PM

3. Operation Panel

3.4 7-Segment Display

7-Segment Display

Row A

Column B

Note: Read the text shown in Row A together with that in Column B to understand the display meaning.

1. IN & V: When the two illuminate together, it indicates input voltage.

2. IN & Hz: When the two illuminate together, it indicates input frequency.

OUT

1. OUT & V: When the two illuminate together, it indicates output voltage.

2. OUT & Hz: When the two illuminate together, it indicates output frequency.

RUN TIME

RUNTIME & MIN: When the two illuminate together, it indicates the estimated remaining battery

backup time.

SET

When the word ‘SET’ illuminates, it indicates the UPS is in setup mode.

You can adjust the following through the LCD. For setup instructions, refer to the Setup Mode Flow

Chart in Section 5.6.

1. Inverter voltage

2. Inverter frequency

3. Bypass range

4. Economy mode

5. Alarm disable

6. Overload alarm

TEST

1. When the word ‘TEST’ ﬂashes, it means that the UPS is under self test.

2. When the words ‘TEST’ and ‘BATT’ ﬂash together, it indicates the UPS is under battery self test.

BATT

1. BATT & %: When the two illuminate together, it indicates the remaining battery capacity.

2. BATT & V: When the two illuminate together, it indicates battery voltage.

18-09-252-93358B.indb 10 1/9/2019 2:19:28 PM

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite G1000UB Guide de configuration

Tripp Lite

Tripp Lite SmartPro Rackmount SMX1000RT2U Guide de configuration

Tripp Lite

Tripp Lite SM550UNAFTA Manuel utilisateur

Tripp Lite

Tripp Lite SU10000RT3UPM Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Series Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU3000RTXLCD3U Guide de configuration

Tripp Lite

Tripp Lite BCINTERNET500 Manuel utilisateur

Tripp Lite

Tripp Lite SMART3000RM2UL Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU80K Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro ST700HGL Manuel utilisateur

Tripp Lite

Tripp Lite SMART1000LCDU Manuel utilisateur

Tripp Lite

Tripp Lite HT850UPS Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMX3000XLRT2UA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SmartPro Rackmount Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART3000RM2UP Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART700USB Guide de configuration

Tripp Lite

Tripp Lite ECO750UPSTAA Manuel du propriétaire

Tripp Lite

Tripp Lite SmartPro SMART1500RM2U Manuel utilisateur

Tripp Lite

Tripp Lite LCDT Series Manuel utilisateur

Tripp Lite

Tripp Lite BC800U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Rackmount SMX1000RT2U Manuel utilisateur

Tripp Lite

Tripp Lite INTERNET550U Manuel utilisateur

Tripp Lite

Tripp Lite OmniSmart OMNI650LCD Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro 450 RTI Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur