Tripp Lite OMNIVSX850 Manuel utilisateur

UPS Systems

Models:

OMNIVSX850, OMNIVSX850D, OMNIVSX1000,

OMNIVSX1000D, OMNIVSX1500, OMNIVSX1500D

(Series Numbers: AG-02FC, AG-02F5, AG-87E4, AG-02FD, AG-87E6, AG-02FE)

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Español 12 • Français 23 • Русский 34 • Deutsch 45

18-07-252-93388F.indb 1 10/3/2018 10:10:23 AM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of this product. Failure to heed these warnings may

affect the warranty.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or

direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• Only set the UPS upright on a sturdy ﬂat surface. Do not block fans or ventilation holes, as this will

seriously inhibit the unit's internal cooling and cause product damage not covered under warranty.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the UPS into itself;

this will damage the UPS.

• Do not modify the UPS plug, and do not use an adapter that would eliminate the UPS ground

connection.

• Do not use extension cords to connect the UPS to an AC outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide clean,

ﬁltered, computer-grade output.

• The mains socket outlet that supplies the UPS should be easily accessible and located near the

UPS.

Equipment Connection Warnings

Short Circuit backup protection and overcurrent protection is provided by the

building installation.

To reduce the risk of ﬁre, connect only to a circuit provided branch circuit

overcurrent protection. The plug on the power supply cord is intended to serve

as the disconnect device. Be sure the socket-outlet is installed near the

equipment and is made easily accessible.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to signiﬁcantly affect its safety or

effectiveness is not recommended.

• Do not connect surge protectors or extension cords to the output of your UPS. This might damage

the UPS and may affect the surge protector and UPS warranties.

• Connect the UPS to an outlet that is adequately protected against excess currents, short circuits

and earth faults as part of the building installation.

Important Safety Instructions

18-07-252-93388F.indb 2 10/3/2018 10:10:23 AM

Important Safety Instructions

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (Sealed Lead-Acid).

The batteries are recyclable. Refer to your local codes for disposal requirements or visit

http://www.tripplite.com/support/recycling-program for recycling information. Tripp Lite offers a

complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the

Web at http://www.tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc replacement

battery for your UPS.

CAUTION: A battery can present a risk of electrical shock and high short-circuit

current. Contact with any part of a grounded battery can result in electrical shock.

The following precautions should be observed when working on batteries:

• Remove watches, rings or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

• Disconnect the charging source and load prior to installing or maintaining the battery.

• Remove battery grounds during installation and maintenance to reduce likelihood of

shock.

• Remove the connection from ground if any part of the battery is determined to be

grounded.

• Unplug the UPS from the AC mains receptacle. Disconnect all cables, including the

equipment plugged into the UPS.

• Servicing of batteries should be performed or supervised by personnel knowledgeable

about batteries and required precautions.

• When replacing batteries, replace with the same type and number of batteries or battery

packs.

• CAUTION: Do not dispose of batteries in a ﬁre. The batteries may explode.

• CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin

and eyes. It may be toxic.

UPS and Battery Recycling

Tripp Lite products use sealed lead-acid batteries, which are highly recyclable.

Call Tripp Lite at 1.773.869.1234 or visit www.tripplite.com/support/recycling-program for

more information on recycling the batteries or any other Tripp Lite product. Please refer to

local codes for disposal requirements.

18-07-252-93388F.indb 3 10/3/2018 10:10:23 AM

STEP 1: Plug the UPS into a properly grounded outlet.

After plugging the UPS into a wall outlet, press and hold the power button until a beep is heard, then

release to turn on the UPS.

Note: The UPS will not turn on automatically in the presence of live utility power.

Quick Installation

OMNIVSX850/1000/1500 OMNIVS850D/1000D/1500D

STEP 2: Plug your equipment into the UPS.

Outlets marked BATTERY & SURGE offer UPS battery backup support during power failures. Connect

your vital computer equipment into these outlets.

Your UPS is designed to support electronic equipment only. You will overload the UPS if the total

volt-amp (VA) ratings for all the equipment connected to the BATTERY/SURGE PROTECTED outlets

exceed the UPS output capacity. To ﬁnd your equipment’s VA ratings, look on their nameplates. If the

equipment is listed in amps (A), multiply the number of amps by 230 to determine VA. For example:

1A × 230 = 230VA. If you suspect you have overloaded the outlets, check Load Meter screens (see

Display UPS/Power Conditions in Basic Operation).

Use the two included C14

to C13 cables to connect

equipment to the UPS.

For illustrative purposes only.

User must supply power cord and plug

that is compatible with power outlets used in that region.

Connected

Equipment

Local

Utility

Power

OMNIVSX1500 model shown. Number of outlets

and outlet layout may differ by model.

OMNIVSX1500D model shown.

18-07-252-93388F.indb 4 10/3/2018 10:10:23 AM

Quick Installation

STEP 3: Turn on the UPS.

After connecting your equipment to the UPS, press and hold the power button until a beep is heard,

then release to turn on your UPS.

If the on-line AC power icon does not illuminate when the UPS is turned ON, try the following:

1. Make sure the UPS is plugged into a live AC outlet.

2. Press the power button to turn on the UPS. A beep should sound when the UPS starts.

3. If the UPS still does not start, contact Tripp Lite Tech Support for assistance.

Basic Operation

UPS ON/OFF

• Plug the UPS into a live, grounded outlet: The entire LCD screen will illuminate for 4 seconds,

then the display will report the output voltage of “0V”. BATTERY/SURGE PROTECTED outlets will be

OFF. The battery charger will engage as necessary.

• Plug equipment into the UPS: You will overload the UPS if the total volt-amp (VA) ratings for

all the equipment connected to the BATTERY/SURGE PROTECTED outlets exceed the UPS output

capacity. To ﬁnd your equipment’s VA ratings, look on their nameplates. If the equipment is listed

in amps (A), multiply the number of amps by 230 to determine VA. For example: 1A × 230 =

230VA.

• Turn the UPS on: Press and hold the power button until the alarm sounds, then release. The

UPS alarm will beep for 2 seconds. The BATTERY/SURGE PROTECTED outlets will begin passing

AC line power. The UPS will automatically recharge internal batteries as needed. Once turned on,

your UPS is ready to protect connected equipment from blackouts, brownouts, overvoltages and

transient surges.

• Turn the UPS off: Press the power button.

Note: UPS system will function properly upon initial startup. However, maximum runtime for the unit’s

battery will only be accessible after it has been charged for 24 hours.

18-07-252-93388F.indb 5 10/3/2018 10:10:23 AM

Basic Operation

Display UPS/Power Conditions

On-Line AC Power Mode LCD Data

The LCD touchscreen offers ﬁve screens of UPS and site power information when the UPS is

operating in line-power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %, Battery Charge

Level) are available for viewing in line-power mode. Press the front panel LCD to advance to the next

screen. Screen 5 (Overload) is displayed automatically only when the UPS is loaded to levels greater

than 110%.

The LCD screen reports that AVR (Auto Voltage Regulation) buck/boost circuits are active any time

the line power icon is ﬂashing.

1Output Voltage 2Input Voltage 3Load %

Note: The LCD touchscreen automatically turns off in line-power mode 20 seconds after it was last touched. To

re-activate the LCD for an additional 20 seconds, touch the screen.

Operating Mode Alarm Description

Battery Mode Normal No Alarm

Battery Low Sounds Every Second

Over Load Sounds Every 0.5 Second

Line Mode Normal No Alarm

Over Load Sounds Every 0.5 Second

Battery Replace Sounds Every Minute

Fault Mode Sounds Continuously

4Battery Charge Level 5Overload

18-07-252-93388F.indb 6 10/3/2018 10:10:24 AM

Basic Operation

Battery Power Mode LCD Data

The LCD touchscreen offers ﬁve screens of UPS and site power information when the UPS is

operating in line-power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %, Battery Charge

Level) are available for viewing in line-power mode. Press the front panel LCD to advance to the next

screen. Screen 5 (Overload) is displayed automatically only when the UPS is loaded to levels greater

than 110%.

Critical Fault Screens

Error Code Critical Fault Solution

F01 OUTPUT SHORT Disconnect load(s) from UPS outlets. Power off UPS and

contact Tripp Lite Technical Support for assistance.

F02 OVER LOAD Remove excess load, check load meter on LCD for load status.

F03 OVER CHARGE Turn unit off, unplug UPS and contact Tripp Lite Technical

Support for assistance.

F04 BATTERY LOW

VOLTAGE

Charge UPS for 24 hours. If problem persists, replace battery

and contact Tripp Lite Technical Support if problem persists.

F05 BATTERY MODE

HIGH OUTPUT

Turn off power to the UPS and contact Tripp Lite Technical

Support for assistance.

1Output Voltage 2Input Voltage 3Load %

4Battery Charge Level 5Overload

Note: The touchscreen LCD will remain ON continuously during battery mode operation.

18-07-252-93388F.indb 7 10/3/2018 10:10:25 AM

IN OUT

Features

Front Panel

Rear Panel

OMNIVSX1500 model shown. Number of outlets

and outlet layout may differ by model.

OMNIVSX1500D model shown.

1ON/OFF Button: When the UPS is OFF, press and hold the ON/OFF button until a beep is heard

to turn the UPS ON. When the UPS is ON, press and hold the ON/OFF button to turn the UPS

OFF.

2LCD Touchscreen Panel: Provide current status of the UPS. For a detailed description, refer to

“Display UPS/Power Conditions” in the Basic Operation section.

3Battery Backup/Surge Protected Outlets: These outlets offer battery backup support and

premium surge suppression for critical devices requiring battery backup support.

4USB Communication Port: This port can connect your UPS to any computer for automatic

saves and unattended shutdown in the event of a power failure. Use with Tripp Lite’s

PowerAlert®Software (available as a FREE download at www.tripplite.com) and the USB cable

included with your UPS. This connection is optional; your UPS will work properly without this

connection.

Note: This UPS System provides basic communication compatibility with most integrated Windows®,

Macintosh®and Linux®power management applications.

18-07-252-93388F.indb 8 10/3/2018 10:10:26 AM

Features

Battery Replacement

Under normal conditions, the original battery in your UPS will last several years. Battery replacement

should only be performed by qualiﬁed personnel. Refer to “Battery Warnings” in the Important

Safety Instructions section for more information.

Models OMNIVSX850 and OMNIVSX850D require one 12V DC, 9Ah replacement battery.

Models OMNIVSX1000 and OMNIVSX1000D require one 12V DC, 9Ah replacement battery.

Models OMNIVSX1500 and OMNIVSX1500D require two 12V DC, 9Ah replacement batteries.

For further information about replacement compatibility and ordering, visit

www.tripplite.com/products/battery-ﬁnder.

Battery replacement must be done using the same battery type and

quantity: 12V DC sealed lead-acid, 6-cell and in compliance with UL 1989.

CAUTION: Risk of energy hazard. Before replacing batteries, remove conductive

jewelry such as chains, wristwatches and rings. High energy passing through

conductive materials may cause severe burns.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries according to instructions.

5AC Power Input: Plug in a C14 power cord (OMNIVSX850/1000/1500 models) or use the

included 1.5 m power cord with Schuko plug (OMNIVS850D/1000D/1500D models) to connect

the UPS to the mains power source.

6Resettable Input Circuit Breaker: Protects your electrical circuit from overcurrent draw

from the UPS load. If this breaker trips, remove some of the load, then reset by pressing it in.

Breaker is rated for 5A, 7A or 10A, 250V AC.

7Variable-Speed Cooling Fan (OMNIVSX1500 and OMNIVSX1500D models only): This fan

regulates the internal temperature of the UPS.

18-07-252-93388F.indb 9 10/3/2018 10:10:26 AM

Storage and Service

Storage

To avoid battery drain, all connected equipment should be turned off and disconnected from the

UPS. Press the power button and disconnect the unit from AC power. Your UPS will be completely

turned off (deactivated), and will be ready for storage. If you plan on storing your UPS for an

extended period, fully recharge the UPS batteries every three months. Plug the UPS into a live AC

outlet, turn it on by pressing the power button and allow the batteries to recharge for 4 to 6 hours. If

you leave your UPS batteries discharged for a long period of time, they will suffer a permanent loss

of capacity.

Service

A variety of Extended Warranty and On-Site Service Programs are available from Tripp Lite. For more

information on service, visit www.tripplite.com/support.

Before returning your product for service, follow these steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit www.

tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link.

From here you can request a Returned Material Authorization (RMA) number, which is required

for service. This simple on-line form will ask for your unit’s model and serial numbers, along

with other general purchaser information. The RMA number, along with shipping instructions,

will be emailed to you. Any damages (direct, indirect, special or consequential) to the product

incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered

under warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must

have transportation charges prepaid. Mark the RMA number on the outside of the package. If the

product is within its warranty period, enclose a copy of your sales receipt. Return the product for

service using an insured carrier to the address given to you when you request the RMA.

18-07-252-93388F.indb 10 10/3/2018 10:10:26 AM

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite SmartPro SLT SMX750SLT Guide de configuration

Tripp Lite

Tripp Lite AVRX750UA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Series Manuel utilisateur

Tripp Lite

Tripp Lite HT850UPS Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro VS Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMX1200XLHG Manuel utilisateur

Tripp Lite

Tripp Lite HT1000UPS Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Rackmount Manuel utilisateur

Tripp Lite

Tripp Lite ECO UPS System Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU10000RT3U2TF Manuel utilisateur

Tripp Lite

Tripp Lite BC800U Manuel utilisateur

Tripp Lite

Tripp Lite AVRX550U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU8000RT3UHW Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART750RMXL2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline 200703028 Manuel utilisateur

Tripp Lite

Tripp Lite AGSM8268 Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SUINT3000RTXL2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU3000RTXL3U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU1500RTXLCD2U Guide de configuration

Tripp Lite

Tripp Lite SMART750SLT Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Rackmount SMX1500XLRT2U Guide de configuration

Tripp Lite

Tripp Lite Line-Interactive UPS System SMART750USB Manuel utilisateur

Tripp Lite

Tripp Lite INTERNET350U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART5000RT3U Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur