Tripp Lite OMNISMART350HG Manuel utilisateur

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Quick Installation 3

Basic Operation 5

Storage & Service 10

Specifications 12

SmartPro®is a registered trademark of Tripp Lite. OmniSmart™is a trademark of Tripp Lite.

Español 13

Français 25

SmartPro®&

OmniSmart™

Medical Grade UPS Systems

• Full Isolation (Less than 300µA Leakage)

• Hospital-Grade Plug & Receptacles

• Line-Interactive Operation

• 120V Input

• 330 - 1000VA Output Capacities

OmniSmart™

UPS Systems with

Hospital-Grade Plugs &

Receptacles

• Hospital-Grade Plug & Receptacles

• Line-Interactive Operation

• 120V Input

• 450 - 1400VA Output Capacities

UL1778 UL1778

2601-1

www.tripplite.com/warranty

UPS Location Warnings

• Your UPS incorporates fusing only in the ungrounded phase conductor. UL2601-1 certified

UPS systems (see Specifications) must not be used in countries other than the United States

and Canada and must be used only in health care facilities on grounded systems where

conditions of maintenance and supervision ensure that only qualified

persons will service the electrical distribution system.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight and

conductive contaminants.

• Your UPS is not suitable for use in the presence of a flammable anaesthetic mixture with air,

oxygen or nitrous oxide.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the UPS into

itself; this will damage the UPS.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the UPS’s

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be voided

if anything other than Tripp Lite surge suppressors are used to connect your UPS to an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide

clean, filtered, computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support devices in which a malfunction or failure

of a Tripp Lite UPS System could cause failure or significantly alter the performance of a

life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This may

damage the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any reason. There

are no user-serviceable parts inside.

• Because the batteries present a risk of electrical shock and burn from high short-circuit current,

observe proper precautions. Unplug and turn off the UPS before performing battery replacement.

Use tools with insulated handles, and replace the existing batteries with the same number and

type of new batteries (Sealed Lead-Acid). Do not open the batteries. Do not short or bridge the

battery terminals with any object.

• Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.).

Visit Tripp Lite on the Web at www.tripplite.com/support/battery/index.cfm to locate the

specific replacement battery for your UPS.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements, or in the

USA only call 1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit

www.rbrc.com for recycling information. Do not dispose of the batteries in a fire.

• If your UPS is equipped with an external battery connector, only connect Tripp Lite external

battery packs of the appropriate voltage.

• If your UPS is not equipped with an external battery connector, do not attempt to add external

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings will void your warranty.

Quick Installation

Note! Although some installation procedures are common to all models, some procedures vary depending

on whether you are installing a SmartPro model or an OmniSmart model.

For All Models—Plug your UPS

into a 3-wire grounded, 120V AC,

60 Hz utility outlet.

Note: UL2601-1 listed UPS systems only meet UL standard 2601-1

for medical equipment when plugged into a hospital-grade outlet.

For SmartPro Models Only:

After you plug the UPS into a live AC outlet, the

UPS will automatically charge its batteries, but

will not supply power to its outlets until it is

turned ON (see Step 3 below). The BATTERY

CHARGE LED will be the only LED illuminated.

For OmniSmart Models Only:

Your UPS will run a self-test after it is plugged

in. See Basic Operation to understand the results of

its self-test.

For All Models—Plug your

equipment into the UPS.*

* Your UPS is designed to only support computer equipment. You

will overload the UPS if the total VA ratings for all the equipment

you connect exceeds the UPS’s Output Capacity (see

Specifications). To find your equipment’s VA ratings, look on their

nameplates. If the equipment is listed in amps, multiply the number

of amps by 120 to determine VA. (Example: 1 amp × 120 = 120 VA).

If you are unsure if you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

For SmartPro Models Only—Turn

the UPS ON.

Press and hold the “POWER” button for one

second. The alarm will beep once briefly after

one second has passed. Release the button.

For OmniSmart Models Only—

Select UPS Operating Mode.*

Press the UPS/STANDBY button to toggle your

UPS between the UPS (“POWER” LED lit) and

the STANDBY (“POWER” LED flashing)

modes. Choose the operating mode based on

your location:

USA, Canada & Western Europe:

• Leave the UPS in the UPS mode at all times.

All Other Countries:

• Put the UPS in the STANDBY mode when

you are not using connected equipment.

(WARNING! When set to “CHARGE ONLY,” the UPS will not

provide battery backup during a blackout or brownout.)

• Put the UPS in the UPS mode when you are

using connected equipment.

*See Basic Operation section for a complete explanation of

each mode.

These connections are optional. Your UPS will function properly without these connections.

Serial Communications

(Select models only)

Using the cable provided, connect the DB9 port

of your computer to the DB9 port of your UPS.

Download the PowerAlert UPS monitoring

software program appropriate for your operating

system from www.tripplite.com and install it on

your computer.

USB Communications

(Select Models Only)

Using the cable provided, connect the USB port

of your computer to the USB port of your UPS.

Download the PowerAlert UPS monitoring

software program appropriate for your operating

system from www.tripplite.com and install it on

your computer.

Tel/DSL Protection

(Select Models Only)

Using telephone cords, connect your wall jack

to the UPS jack marked “LINE” (or “IN”) and

your equipment to the UPS jack marked

“EQUIP” (or “OUT”). This will protect your

equipment from surges over the phone line, but

you should make sure that your equipment is

also protected against surges on the AC line.

UPS models with tel/DSL protection can protect

two lines on one cable simultaneously. If you

want to protect two lines that travel through

separate cables, you must use “Y” splitters

appropriate to your application to adapt them to

your UPS's phone jacks.

External Batteries

(Select Models Only)

External batteries are only needed to extend run-

time. Adding external batteries will increase

recharge time as well as runtime.

The illustration shows the location of your UPS’s

External Battery Connector, where you will

insert the battery pack cable. Complete installation

and mounting instructions for your battery pack

appear in the battery pack’s owner’s manual.

Make sure that cables are fully inserted into their

connectors. Small sparks may result during battery

connection; this is normal.

Quick Installation

optional

IN OUT SEE MANUAL FOR

PROPER CONNECTION

NORM

Note! Although some operational features and functions are common to all models, some

operational features vary depending on whether you are operating a SmartPro model or an

OmniSmart model.

For SmartPro Models Only—“POWER” Button:

• To turn the UPS ON: with the UPS plugged into a live AC wall outlet,*

press and hold the POWER button for about two seconds.** Release the

button. If utility power is absent, you can “cold-start” the UPS (i.e.: turn

it ON and supply power for a limited time from its batteries***) by pressing

and holding the POWER button for about two seconds.**

• To turn the UPS OFF: with the UPS ON and receiving utility power,

press and hold the POWER button for one second.** Then unplug the

UPS from the wall outlet. The UPS will be completely OFF.

*After you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries,

but will not supply power to its outlets until it is turned ON. ** The alarm will beep once briefly

after the indicated interval has passed. *** If fully charged.

For OmniSmart Models Only—“UPS/STANDBY” Button:

Use the UPS/STANDBY button to do three things:

Switch your UPS’s Operating Mode: While your UPS is plugged into a

live AC outlet, press the UPS/STANDBY button and hold it until you hear

a beep (about 2 seconds) to toggle between the following operating modes.

Choose your UPS’s operating mode based on the regional guidelines in

Step 3 of the Quick Installation section.

• UPS Mode: ENABLES battery backup. UPS Conditions: While receiv-

ing adequate utility line power, the UPS supplies power to its AC recep-

tacles and charges its batteries; its “POWER” indicator light will be lit.

If the utility line power fails or becomes inadequate, the UPS will supply

inverted AC power to its receptacles if its batteries are sufficiently

charged. Setting Advantages: Provides battery backup during blackouts

or brownouts.

• STANDBY Mode: DISABLES battery backup. UPS Conditions: While

receiving adequate utility line power, the UPS supplies power to its AC

receptacles and charges its batteries; the “POWER” indicator light will

be flashing. Setting Advantages: Continues to charge the battery when

power is present while turning OFF the inverter to prevent battery deple-

tion during power outages when equipment is not in use.

Cold-Start Your UPS: You may “cold start” your UPS and use it as a

stand-alone power source when utility power is not present, providing that

the UPS battery is charged. To “cold start” your UPS, press and hold the

UPS/STANDBY button until you hear a beep (about 2 seconds), then

release it. The “BATTERY CHARGE/BATTERY POWER” indicator light

will illuminate and AC power inverted from stored battery power will be

provided at the UPS receptacles.

Shut Down Your UPS: Press and hold the UPS/STANDBY button when

AC line power is absent (i.e. during a blackout, or when the UPS is

unplugged) to deactivate your UPS.

Buttons

Basic Operation

For All Models—“MUTE/TEST” Button:

To Silence (or “Mute”) UPS Alarms: briefly press and release the

MUTE/TEST button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and

hold the MUTE/TEST button for two seconds.* Continue holding the button

until the alarm beeps several times and the UPS performs a self test. See

“Results of a Self-Test” below. Note: you can leave connected equipment

on during a self-test. Your UPS, however, will not perform a self-test if it

is not turned ON (see "POWER" Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will

remove safe electrical grounding and may introduce a damaging surge

into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.**

If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm

continues to sound after the test, the UPS’s outlets are overloaded. To

clear the overload, unplug some of your equipment and run the self-test

repeatedly until the “OUTPUT LOAD LEVEL” LED is no longer lit

red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user imme-

diately following a self-test may cause the UPS to shutdown and

cease supplying output power in the event of a blackout or severe

brownout.

If the “BATTERY WARNING” LED remains lit and the alarm continues

to sound after the test, the UPS batteries need to be recharged or

replaced. Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED remains lit, contact Tripp Lite for service.

If your UPS requires battery replacement, visit www.tripplite.com/sup-

port/battery/index.cfm to locate the specific Tripp Lite replacement

battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed. ** SmartPro models’

operation during the self-test: the “POWER” LED will be flashing and the “OUTPUT LOAD

LEVEL” and “BATTERY CHARGE” LEDs will be lit and the UPS alarm will sound. OmniSmart

models’ operation during the self-test: all LEDs will be lit and the UPS alarm will sound.

Basic Operation

continued

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

“POWER” LED

For SmartPro Models Only: this green LED lights continuously

when the UPS is ON and supplying connected equipment with AC

power from a utility source. The LED flashes and an alarm sounds (4

short beeps followed by a pause) to indicate the UPS is operating

from its internal batteries during a blackout or severe brownout. If the

blackout or severe brownout is prolonged, you should save files and

shut down your equipment since internal battery power will eventually

be depleted. See “BATTERY CHARGE” LED description below.

For OmniSmart Models Only: this green light will turn ON whenev-

er your UPS is receiving normal AC line power. It will flash while the

UPS is in CHARGE ONLY mode to indicate that the UPS will not

provide battery backup during a blackout or brownout.

“VOLTAGE CORRECTION” LED (For Select SmartPro and

OmniSmart Models): this green LED lights continuously whenever

the UPS is automatically correcting high or low AC voltage on the

utility line without the assistance of battery power. The UPS will also

emit a slight clicking noise. These are normal, automatic operations

of the UPS. No action is required on your part.

“OUTPUT LOAD LEVEL” LED (For Select SmartPro and

OmniSmart Models):

For SmartPro Models Only: this multicolored LED indicates the

approximate electrical load of equipment connected to the UPS's AC

outlets. It will turn from green (light load) to yellow (medium load)

to red (overload). If the LED is red (either illuminated continuously

or flashing), clear the overload immediately by unplugging some of

your equipment from the outlets until the LED changes from red to

yellow (or green) and the alarm is no longer sounding. CAUTION! Any

overload that is not corrected by the user immediately may cause the

UPS to shut down and cease supplying output power in the event of a

blackout or severe brownout.

For OmniSmart Models Only: this red light will turn ON continuously

when the UPS is providing power from battery or after the UPS runs

a self-test to indicate that the UPS's inverter is overloaded. If it lights

up, immediately remove some of the equipment connected to the UPS

and run a self-test. Large overloads may cause your UPS to shut down.

Indicator Lights

Basic Operation

continued

“BATTERY CHARGE / BATTERY POWER” LED:

For SmartPro Models Only: when the UPS is operating from utility

power, this LED indicates the approximate charge state of the UPS’s

internal batteries: red indicates the batteries are beginning to charge;

yellow indicates the batteries are roughly midway through charging;

and green indicates the batteries are fully charged. When the UPS is

operating from battery power during a blackout or severe brownout,

this LED indicates the approximate amount of energy (ultimately

affecting runtime) that the UPS’s batteries will provide: red indicates

a low level of energy; yellow indicates a medium level of energy; and

green indicates a high level of energy. Since the runtime performance of

all UPS batteries will gradually deplete over time, it is recommended

that you periodically perform a self-test (see “MUTE/TEST” Button

description) to determine the energy level of your UPS batteries

BEFORE a blackout or severe brownout occurs. During a prolonged

blackout or severe brownout, you should save files and shut down

your equipment since battery power will eventually be depleted.

When the LED turns red and an alarm sounds continuously, it indicates

the UPS’s batteries are nearly out of power and UPS shut down is imminent.

For OmniSmart Models Only: this LED will illuminate when your

UPS is providing your equipment with battery backup power.

“BATTERY WARNING” LED: this LED lights red and an alarm

sounds intermittently after you initiate a self test (See “MUTE/TEST”

Button description) to indicate the UPS batteries need to be recharged

or replaced. Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED continues to light, contact Tripp Lite

for service. If your UPS requires battery replacement, visit www.trip-

plite.com/support/battery/index.cfm to locate the specific Tripp Lite

replacement battery for your UPS.

Basic Operation

continued

Hospital Grade AC Receptacles: The receptacles provide your con-

nected equipment with AC line power during normal operation and

battery power during blackouts and brownouts. They also protect your

equipment against damaging surges and line noise.

Tel/DSL Protection Jacks (Select Models Only): These jacks protect

connected equipment against surges travelling over the modem/fax or

telephone line. Connecting your equipment to these jacks is optional.

Your UPS will still work properly without this connection.

DB9 Port (Select Models Only): The DB9 port connects your UPS to

any workstation or server. Use with Tripp Lite’s PowerAlert UPS

monitoring software and a DB9 cable to enable your computer to

automatically save open files and shut down equipment during a

blackout. The UPS can also report power availability and UPS status,

and select UPS models have other capabilities. Consult your

PowerAlert manual for more information.

USB Port (Select Models Only): The USB port connects your UPS

to any workstation or server. Use with Tripp Lite’s PowerAlert UPS

monitoring software and an USB cable to enable your computer to

automatically save open files and shut down equipment during a

blackout. The UPS can also report power availability and UPS status,

and select UPS models have other capabilities. Consult your

PowerAlert manual for more information.

Battery Replacement Door: Under normal conditions, the original

battery in your UPS will last several years. Refer to “Battery

Warnings” in the Safety section on page 2.

External Battery Connector (Select Models Only): Use to connect

one or more Tripp Lite battery packs for additional runtime. Refer to

Specifications and/or the label next to the connector to determine the

appropriate variety of battery pack to use. Refer to the battery pack

instruction manual for complete installation information and important

safety warnings.

Input Breaker (Select Models Only): Protects your electrical circuit

from overcurrent draw from the UPS load. If this breaker trips,

remove some of the load, then reset it by pressing the breaker in.

Equipotential Connection (Select Models Only): Use this to connect

any equipment that requires a chassis ground.

Other UPS Features

Basic Operation

continued

Storage

For SmartPro Models Only: CAUTION! Your UPS has an internal power source. Its outlets

may still deliver current, even after the UPS is unplugged, until the UPS is completely turned

OFF (deactivated). Before storing your UPS, turn it completely OFF: with the UPS ON and

receiving utility power, press and hold the POWER button for one second (an alarm will beep

once briefly after the interval has passed); then, unplug the UPS from the wall outlet. If you

store your UPS for an extended period of time, recharge the UPS batteries once every three

months: plug the UPS into a wall outlet; allow it to charge for 12 hours; and then unplug it and

place it back in storage. Note: after you plug the UPS in, it will automatically begin charging its

batteries; however, it will not supply power to its outlets (see Quick Installation section). If you

leave your UPS batteries discharged for an extended period of time, they will suffer a permanent

loss of capacity.

For OmniSmart Models Only: All connected equipment should be turned off, then disconnected

from the UPS to avoid battery drain. Unplug your UPS from its AC receptacle. CAUTION:

Your UPS has an internal power source. Its outlets may still deliver current after it is

unplugged, until the UPS is deactivated. To deactivate the UPS, press and hold its

UPS/STANDBY button. Your UPS is now ready for storage. If you plan on storing your UPS

for an extended period of time, fully recharge the UPS batteries once every three months by

plugging the UPS into a live AC outlet and letting the UPS charge for 12 hours. If you leave

your UPS batteries discharged for an extended period of time, they will suffer a permanent loss

of capacity.

Storage & Service

Power Sensitivity Adjustment (Select Models Only): This dial is

normally set fully counterclockwise, which enables the UPS to pro-

tect against waveform distortions in its AC input. When such distor-

tion occurs, the UPS will normally switch to providing PWM sine

wave power from its battery reserves for as long as the

distortion is present. In areas with poor utility power or where the

UPS’s input power comes from a backup generator, chronic waveform

distortion could cause the UPS to switch to battery too frequently,

draining its battery reserves. You may be able to reduce how often your

UPS switches to battery due to waveform distortion by experiment-

ing with different settings for this dial. As the dial is turned clock-

wise, the UPS becomes more tolerant of variations in its input

power’s AC waveform. NOTE: The further the dial is adjusted clock-

wise, the greater the degree of waveform distortion the UPS will

allow to pass to connected equipment. When experimenting with dif-

ferent settings for this dial, operate connected equipment in a safe test

mode so that the effect on the equipment of any waveform distortions

in the UPS’s output can be evaluated without disrupting critical oper-

NORM DELAY

Basic Operation

continued

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite ECO UPS System Manuel utilisateur

Tripp Lite

Tripp Lite AVRX550U Manuel utilisateur

Tripp Lite

Tripp Lite AVRX550UA Manuel utilisateur

Tripp Lite

Tripp Lite 1250-3000 VA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SLT SMX750SLT Guide de configuration

Tripp Lite

Tripp Lite AG-02F0 Series Manuel utilisateur

Tripp Lite

Tripp Lite OMNIVSX850 Manuel utilisateur

Tripp Lite

Tripp Lite OmniSmart Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU1500LCD1U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU5000RT3U Manuel utilisateur

Tripp Lite

Tripp Lite SMART1000LCDTAA Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU10000RT3U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro Series Manuel utilisateur

Tripp Lite

Tripp Lite RBC11A Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU3000RTXL2U Manuel utilisateur

Tripp Lite

Tripp Lite Internet Office 700 Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU10KRT1X Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU750RTXLCD2U Manuel utilisateur

Tripp Lite

Tripp Lite ECO Series Manuel utilisateur

Tripp Lite

Tripp Lite INTERNET OFFICE 350 Manuel utilisateur

Tripp Lite

Tripp Lite OmniSmart OMNIVSINT500 Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU2200RTXL2UA Manuel utilisateur

Tripp Lite

Tripp Lite BC Personal Datashield BCPERS300 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur