Texas Instruments MSP432P401R Manuel utilisateur

MSP432P401R Launchpad External Target Mod

This guide walks through the steps of connecting to and programming an external target using

the MSP432P401R LaunchPad Development Kit.

Figure 1: MSP432P401R LaunchPad Development Kit

Step 1:

Remove the board from the packaging.

Figure 2: MSP432P401R LaunchPad out of box (with wires attached)

Step 2:

Remove the jumpers from the isolation header as well as switch S101 to the “XDS-ET”position (not the

“Ext Debug”position).

Figure 3: Headers Removed and Switch Positioned

Step 3:

Attach wires to each of the positions in J103 on the side of the board near the reset button.

Figure 4: Jumper wires soldered into J103 on the LaunchPad

Step 4:

Attach a wire for the “TDI”signal by soldering a wire into pin 6 of the debug select switch (S101) as

shown in the figure below. Ensure that the switch remains in the “XDS-ET”position.

Figure 5: Wire Soldered to "TDI" Signal on S101

Step 5:

Attach a wire for the “SWO”signal by soldering a wire to pin 12 of IC111. Since the traces are small on

that component, it is easiest to attach the wire directly to the trace.

Figure 6: Wire Soldered to "SWO" Signal from Pin 12 on IC111

Carefully scratch off the soldermask from the trace leading to pin 12 on IC111. This will allow for more

space to solder a wire.

Figure 7: Close-up of IC111 and the Soldering Location for the "SWO" Signal

Solder a wire to the exposed copper of the trace and be careful to not strain the wire as it may damage

the board.

Figure 8: Wire Soldered to the "SWO" Signal

Step 6:

Attach the wires from J103 on the LaunchPad to their corresponding positions on whatever target board

you want to program. Not all signals are required from J103.

Step 7:

Attach the “TDI”and “SWO”wires to their corresponding positions on the target board.

Step 8:

Connect the MSP432P401R LaunchPad to the computer via the micro USB cable and check to see if

“LED102”is illuminated green near the reset button. If the LED is not on, try cycling the power on the

target board by quickly removing and replacing the +3.3V wire. Repeat with pauses in between until

LED02 illuminates.

Figure 9: Launch Pad Connected to Target with LED02 Illuminated

Step 9:

Program the external target board using your preferred method. Note that I have only tried this with

Code Composer Studio and Energia and it works fine but I’m assuming it should work with other IDEs.

No guarantees though.

Autres manuels pour MSP432P401R

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments TMDXRM42HDK Manuel utilisateur

Texas Instruments

Texas Instruments LAUNCHXL-CC1310 Manuel

Texas Instruments

Texas Instruments TMS370 Series Guide de l'utilisateur

Texas Instruments

Texas Instruments SimpleLink CC2650 Manuel utilisateur

Texas Instruments

Texas Instruments CC2530 ZigBee Development Kit Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6735A Manuel utilisateur

Texas Instruments

Texas Instruments CC1200 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430x4xx Family Manuel utilisateur

Texas Instruments

Texas Instruments CC3235MODSF SimpleLink Manuel utilisateur

Texas Instruments

Texas Instruments AM5728 Manuel utilisateur

Texas Instruments

Texas Instruments TDP0604 Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-RS232 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6767 Manuel utilisateur

Texas Instruments

Texas Instruments CC2520 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430FG6626 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67681 Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP430FR2311 Manuel utilisateur

Texas Instruments

Texas Instruments Hercules TMS570LS04 Series Manuel utilisateur

Texas Instruments

Texas Instruments PGA460-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67781 Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink Ethernet MSP432E401Y Manuel utilisateur

Texas Instruments

Texas Instruments AM243 Series Manuel utilisateur

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F533x Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur