Texas Instruments LaunchPad CC1354P10-6 Manuel utilisateur

™

Meet the

CC1354P10-6

LaunchPad

Development Kit

Connect your LaunchPad to a computer

and visit dev.ti.com

Part Number: LP-EM-CC1354P10-6

BoosterPack Ecosystem

SimpleLink ULP Sense

BoosterPack

- Flow meter measurements

- Ultra low power accelerometer

- Two cap touch buttons

- Analog Light Sensor

- Reed switch

- 0-200kΩpotentiometer

See them all @ ti.com/boosterpack

Software Tools SmartRF Studio

A powerful application to

evaluate radio performance.

SimpleLink SDK and

SimpleLink Academy

Advanced software and

tutorials to easy ramp your

development with your new

LaunchPad.

Professional Software tools

LaunchPads are supported by

professional IDEs that

provide industrial-grade

features and full debug-

capability. Set breakpoints,

watch variables, profile code,

inspect memory and more.

Sharp 128x128 Memory

LCD and microSD card

BoosterPack

- 1.28 128 x 128 pixel LCD

(LS013B7DH03)

- microSD card slot

- DCDC 3V to 5V converter

- Ultra-low-power operation

2023 Texas Instruments Incorporated. The platform bar, LaunchPad, EnergyTrace and Code Composer Studio

are trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

The BoosterPack™ connector

The pinout to connect BoosterPack accessories (available separately) are shown below.

www.ti.com/ccs

Code Composer Studio

IDE

3V3

DIO23A0

GND

DIO12

RXD

DIO13

TXD

DIO22

DIO24

DIO10

SPI_CLK

DIO21

DIO4

I2C_SCL

DIO5

DIO19

DIO11

DIO14

LP_RST

DIO9

DIO8

DIO42

DIO41

DIO15

DIO47

DIO46

DIO20

DIO45

DIO18

DIO40

DIO16

DIO17

I2C_SDA

DIO25

DIO26

DIO27

DIO28

DIO29

DIO30

DIO43

DIO44

SPI_CS

BTN_2

DIO40*

SPI_MOSI

SPI_MISO

BTN_1

CTS

RTS SWO

RESET*

TMS

TCK

TDO

TDI

XDS110 EnergyTrace™ Technology

The LP-EM-CC1354P10-6 is compatible with EnergyTrace technology.

EnergyTrace implements a new method for measuring MCU current consumption. It uses

a DC-DC solution to measure the time density of charge pulses, allowing accuracy on

ultra low power measurements. Its high dynamic range (700 nA to 400 mA) and fast

sampling rate (256 kSPS) captures the complete operational profile of the wireless MCU.

Find more information at

ti.com/EnergyTrace

EnergyTrace Profile

EnergyTrace Profile runtime and energy data for low power modes along with each

function run during Active Mode.

Graphical Power Data in Code Composer Studio

These two tabs of the EnergyTrace Technology window show a graph over time of

power and energy.

Available in the LP-XDS110ET Debug Probe and selected LaunchPads

UART (DIO12, DIO13), Reset (LP_RST) and JTAG (TMS, TCK, TDO and TDI) are also present in the

LP-EM Debug Connector. Power (GND, 3V3 and 5V) is also provided.

*These functions are not connected to the LaunchPad connector by default.

SPRUIZ9

A closer look at your new

LaunchPad Development Kit

Featured microcontroller: CC1354P10

This LaunchPad is great for...

- Battery-operated wireless applications operating in the Sub-1 GHz (868 and 915 MHz) and 2.4 GHz ISM

RF bands. It features two 2.4 GHz RF paths up to +14 and +20 dBm and one Sub-1 GHz up to +5 dBm

- Adding RF capabilities to your product using one of the supported protocols: Bluetooth LE, Zigbee,

IEEE 802.15.4g, Wi-SUN®, Wireless M-Bus, MIOTY®and proprietary protocols

What comes in the box?



LP-EM-CC1354P10-6

LaunchPad

CC1354P10 Microcontroller

- 48 MHz CPU

- 1 MB Flash, 256 kB RAM

- Programmable radio supporting

various protocols and up to +20 dBm

at either 868/915 MHz or 2.4 GHz

- Low power consumption

QSG

This Quick

Start Guide

10-pin

Debug Cable

2-wire

Power Cable

CC1354P10

{

- Four 32-bit or eight x 16-bit timers

- ADC with 8 channels, 12 bits and 200 ksamples/s

- DAC with 8 bits

- Serial communications: UART, SPI, I2C

- Two comparators

- Real-time clock

Separate LaunchPad



LP-EM-CC1354P10-6



Hardware setup

What do you need?

To use your new LaunchPad, you need to connect an external Debug Probe to either the 20-pin

LP-EM Debug connector on the edge of the board or to the 10-pin Debug connector and supply

power separately.

Option 1: Using the LP-EM Debug Connector

This is the easiest way to setup the hardware. It requires either an LP-XDS110 or

LP-XDS110ET Debug Probe (sold separately).

Simply connect the edge connector of the Debug Probe to the edge connector of the LaunchPad

and connect the USB port of the Debug Probe to the host computer. A secondary UART

communications channel will also be available and power to the LaunchPad will be provided

directly.

LP-XDS110 or LP-XDS110ET



LP-EM-CC1354P10-6



USB to the host

computer

USB to the host

computer

LP-EM Debug Connector

Together with a LP-XDS110 or

LP-XDS110ET, allows:

- Debugging and programming

- Communicating to the host via UART

- Powering the microcontroller

10-pin Debug Connector

Allows using an external JTAG Debug

Probe to debug/program the device

20-pin BoosterPack

plug-in module connector

(J1, J2, J3 & J4)

Button/Switch

BTN-2 (DIO14)

{

Antenna

CC1354P106T0RSK

Wireless Microcontroller

(under the RF shield)

LP-EM-CC1354P10-6 Overview

Button/Switch

BTN-1 (DIO15)

User LEDs

Red (DIO6)

Green (DIO7)

For additional details, consult dev.ti.com/?id=LP-EM-CC1354P10-6

When using the 10-pin debug connector, the UART communications channel must be wired

separately (this connector does not carry UART signals).

If using a standalone Debug Probe, consult its documentation to see if it supports the ARM

Cortex-M 10-pin standard.

Remove all jumpers,

except GND and 3V3

2-wire Power Cable

Jumper on the position

XDS110 Power

10-pin Debug Cable

Option 2: Using the 10-pin debug connector

Either a standalone debug probe or a separate LaunchPad with a built-in debug probe can

be used.

Connect the two boards as shown in the picture below:

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, regulatory or other requirements.

These resources are subject to change without notice. TI grants you permission to use these resources only for development of an

application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license

is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you

will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these

resources.

TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with

such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for

TI products.

TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Ce manuel convient aux modèles suivants

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Texas Instruments

Texas Instruments CC2531 Manuel utilisateur

Texas Instruments

Texas Instruments TMS570 Manuel utilisateur

Texas Instruments

Texas Instruments OMAP35 Series Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP430FR4133 Manuel utilisateur

Texas Instruments

Texas Instruments CC2431ZDK Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67471 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6775 Manuel utilisateur

Texas Instruments

Texas Instruments CC2543EMs Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2430 Manuel utilisateur

Texas Instruments

Texas Instruments OMAP-L137/C6747 Manuel utilisateur

Texas Instruments

Texas Instruments TAS5805M Manuel utilisateur

Texas Instruments

Texas Instruments CC-Antenna-DK2 Manuel utilisateur

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuel utilisateur

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments C2000 LED BoosterPack Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0G310 Series Manuel utilisateur

Texas Instruments

Texas Instruments TMS570LS12x Manuel utilisateur

Texas Instruments

Texas Instruments MSP430G2955 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6777 Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0L1306 Manuel utilisateur

Texas Instruments

Texas Instruments AFE79 Series Manuel utilisateur

Texas Instruments

Texas Instruments TMS570LS0 32 Series Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67691 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur