Texas Instruments Chipcon Products CC1110DK Manuel de programmation
SWRU078A
CC1110DK Quick Start Instructions Revision 2.0, 2007-08-23
RF/Packet Error Rate Test
1. Kit Contents
•2 SmartRF04EB
•2 CC1110EM
•2 antennas
•2 USB cables
2. EB overview 3. Plug EM into EB
Insert a CC1110EM into both SmartRF04EBs.
The connectors will only fit in one position, so
that the EM cannot be inserted the wrong way.
Do not force the EM.
4a. Battery power
There are three different ways of applying
power to the EB:
The first method involves using a battery, either
a 9V or a 4xAA battery pack connected to the
battery connector on the bottom side of the
board
4b. DC power
The second method applies DC power using the DC
input jack (right in picture, centre is +, sleeve is
ground), or by connecting a 4-10V voltage source
between the 4-10V and 0V terminals of the power
connector (left in picture). It is also possible to
connect a 3.3V voltage source between the 3.3V and
0V terminals. The on-board voltage regulators will be
bypassed in this case.
4c. USB power
The EB can also be powered from the USB bus.
Make sure that the SmartRF
®
Studio software is
installed before connecting the EB to the PC,
otherwise you may experience problems in
installing it later due to driver issues.
Note that if multiple power sources are
connected, the source with the highest voltage
will power the EB. This means that you should
disconnect any attached battery when using a
lab supply or USB power, otherwise the battery
will be drained.
5. Set power switch
If a 3.3V source is used as described in 4b
above, the switch should be set to the leftmost
position. For all other cases, the switch should
be set to the rightmost position. This switch can
be used to turn off the EB by switching it to the
opposite position of that used to turn it on.
6. Packet error rate test
When power is applied to the board, the test
program will start. You should see the Chipcon logo
shown above on the LCD display on both EBs.
Pushing button S1 in the lower right corner of the
board will show the first menu item.
7. Select Frequency
Select frequency according to the type of EM
module in use (315 MHz, 433 MHz, 868 or 915
MHz). Move the joystick up or down to display
the choices and push button S1 in the lower
right corner of the board to select the displayed
frequency.
EM
connectors
LCD screen
Joystick Button S1
Web sites: http://www.ti.com/lpw
TI Worldwide Support: http://www-k.ext.ti.com/sc/technical-
support/product-information-centers.htm
Make sure to subscribe to the Low-Power
RF Newsletter to receive information about
updates to documentation, new product
releases and more. Sign up on our web site!
Address information
SWRU078A
8. EB 1: Select Receiver
Select Receiver on the first EB by moving the
joystick. Confirm by pressing button S1. The
Receiving node will display “Ready to receive”.
9. EB 2: Select Transmitter
Select Transmitter on the other EB by moving the
joystick. Confirm by pressing button S1.
10. EB 2: Number of packets
On the transmitter EB, select the number of
packets to send. More packets takes longer but
gives a better statistical result. Confirm by
pressing button S1.
11. PER Test (Transmitter)
The transmitter will show “Transmitting!” and a
running counter that shows the number of
packets.
12. PER Test (Receiver)
The receiver will show the total accumulated
packet error rate together with the average signal
strength (RSSI) of the previous 50 received
packets.
13. Per Test results
When the PER test is completed, the result will be
displayed on the receiver until a new test is
started. A new test can be started from the
transmitter.
14. Documentation
Please visit www.ti.com to download the
CC1110DK User Manual, the SmartRF
®
Studio
software, examples, as well as relevant
datasheets and application notes.
If you for some reason cannot access the TI
web site and download the files, please contact
your local TI representative for assistance.
15. Troubleshooting/Notice
It you are experiencing problems with this test,
please check the following:
•Please visit
www.ti.com and enter
CC1110DK in the part number search box.
Check for updated SW and documentation.
Updated SW can be downloaded to the
device using IAR or the Flash Programmer
application.
•If results are strange at short distances, try
to move the transmitter and receiver further
apart. The CC1110 may experience
saturation when transmitting at full output
power if the units are to close.
•See “DN300 -- SmartRF04EB
Troubleshooting” for general
troubleshooting of your EB board.
SmartRF
®
Studio
1. Download
Before connecting the EB to your PC, download
SmartRF
®
Studio from www.ti.com. To find it,
type “SmartRF Studio” in the keyword search
field and click Go. Install the program.
2. Plug in EB
After the install program finishes, connect the EB
to the PC using the USB cable. Run SmartRF
®
Studio. Select the SmartRF
®
04 tab. Select the
CC1110 board, and click the Run button.
3. Configure
You can now configure the radio chip, run tests
or communicate with another EB.
Web sites: http://www.ti.com/lpw
TI Worldwide Support: http://www-k.ext.ti.com/sc/technical-
support/product-information-centers.htm
Make sure to subscribe to the Low-Power
RF Newsletter to receive information about
updates to documentation, new product
releases and more. Sign up on our web site!
Address information
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’sstandard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support thiswarranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarilyperformed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers shouldprovide adequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, maskwork right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-party products or services does not constitute a license from TI to use suchproducts or services or a warranty or endorsement thereof. Use of such information may require a license from a third party underthe patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third partiesmay be subject to additional restrictions.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or servicevoids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive businesspractice. TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product wouldreasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreementspecifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramificationsof their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-relatedrequirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding anyapplications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and itsrepresentatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade issolely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements inconnection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI productsare designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use anynon-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandInterface interface.ti.com Digital Control www.ti.com/digitalcontrolLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyLow Power www.ti.com/lpw Video & Imaging www.ti.com/videoWireless
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2007, Texas Instruments Incorporated
Autres manuels pour Chipcon Products CC1110DK
1
Autres manuels Texas Instruments Microcontrôleur
Texas Instruments
Texas Instruments MSP430F563x Manuel utilisateur
Texas Instruments
Texas Instruments CC2531 Manuel utilisateur
Texas Instruments
Texas Instruments CC3220-LAUNCHXL Manuel utilisateur
Texas Instruments
Texas Instruments MSP430F5529 LaunchPad Manuel utilisateur
Texas Instruments
Texas Instruments LaunchPad C2000 F280015 Series Manuel utilisateur
Texas Instruments
Texas Instruments Hercules RM48 Manuel utilisateur
Texas Instruments
Texas Instruments TMS570LC43x Manuel utilisateur
Texas Instruments
Texas Instruments Silicon Errata TMS320F28379S Manuel utilisateur
Texas Instruments
Texas Instruments CC-6LOWPAN-DK-868 Manuel utilisateur
Texas Instruments
Texas Instruments MSP430F6766 Manuel utilisateur
Texas Instruments
Texas Instruments MSP430 series Manuel utilisateur
Texas Instruments
Texas Instruments SN65LVPE512 Manuel utilisateur
Texas Instruments
Texas Instruments MSP430F4152IPM Manuel utilisateur
Texas Instruments
Texas Instruments MSP430 series Manuel utilisateur
Texas Instruments
Texas Instruments OMAP35 Series Manuel utilisateur
Texas Instruments
Texas Instruments TPS6594-Q1 Series Manuel utilisateur
Texas Instruments
Texas Instruments AFE722 Series Manuel utilisateur
Texas Instruments
Texas Instruments MSP430FG6626 Manuel utilisateur
Texas Instruments
Texas Instruments CC2530-CC2592EM Manuel utilisateur
Texas Instruments
Texas Instruments CC3235MODSF SimpleLink Manuel utilisateur
Manuels Microcontrôleur populaires d'autres marques
AMS
AMS AS7261 Demo Kit Manuel utilisateur
Novatek
Novatek NT6861 Manuel utilisateur
Espressif Systems
Espressif Systems ESP8266 SDK Guide de configuration
Nuvoton
Nuvoton ISD61S00 ChipCorder Mode d’emploi
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Manuel utilisateur
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur
NEC
NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation
Mikroe
Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation
Intel
Intel Agilex Manuel utilisateur
Cypress
Cypress CY4607 HX2VL Manuel utilisateur
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Manuel utilisateur
CYPRES
CYPRES CY14NVSRAMKIT-001 Manuel utilisateur
Espressif Systems
Espressif Systems ESP8266EX Mode d'emploi
Abov
Abov AC33M8128L Manuel utilisateur
Laird
Laird BL654PA Manuel utilisateur
Silicon Laboratories
Silicon Laboratories C8051F800 Manuel utilisateur
Energy micro
Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur
Mikroe
Mikroe click Proximity 2 Manuel utilisateur