Struers Labotom-3 Manuel utilisateur
Manual No.: 15327001
Date of Release 04.04.2011
Labotom-3
Instruction Manual
Labotom-3
Instruction Manual
Table of Contents Page
User’s Guide ............................................................... 1
Reference Guide ....................................................... 15
Quick Reference ....................................................... 27
Always state Serial No and Voltage/frequency if you have technical questions or when ordering spare parts.
You will find the Serial No. and Voltage on the type plate of the machine itself. We may also need the Date
and Article No of the manual. This information is found on the front cover.
The following restrictions should be observed, as violation of the restrictions may cause cancellation of
Struers legal obligations:
Instruction Manuals: Struers Instruction Manual may only be used in connection with Struers equipment
covered by the Instruction Manual.
Service Manuals: Struers Service Manual may only be used by a trained technician authorised by Struers.
The Service Manual may only be used in connection with Struers equipment covered by the Service Manual.
Struers assumes no responsibility for errors in the manual text/illustrations. The information in this manual is
subject to changes without notice. The manual may mention accesso
ries or parts not included in the present
version of the equipment.
Original instructions. The contents of this manual is the property of Struers. Reproduction of any part of this
manual without the written permission of Struers is not allowed.
All rights reserved. © Struers 2011.
Struers A/S
Pederstrupvej 84
DK-2750 Ballerup
Denmark
Telephone +45 44 600 800
Fax +45 44 600 801
Labotom-3
Instruction Manual
Labotom-3
Safety Precaution Sheet
To be read carefully
before use
1. The operator(s) should be fully instructed in the use of the machine and
its cut-off wheels according to the Instruction Manual and the
instructions for the cut-off wheels.
2. The machine must be placed on a safe and stable support table. All the
machines safety functions and guards must be in working order.
3. Use only intact cut-off wheels. The cut-off wheels must be approved for
min. 50 m/s.
4. Observe the current safety regulations for handling, mixing, filling,
emptying and disposal of the additive for cooling fluid.
5. The workpiece must be securely fixed in the quick-clamping device or
the like. Large or sharp workpieces must be handled in a safe way.
6. Protruding workpieces should be shielded or marked.
7. The cutting handle should be lowered slowly and carefully, in order to
avoid breaking the cut-off wheel.
8. Struers recommends the use of an exhaust system as the materials to
be cut may emit harmful gasses or dust.
9. Do not open the protection guard before the cut-off wheel has stopped
completely.
10. Do not put your hands through the rubber curtain during operation of
the machine.
The equipment should only be used for its intended purpose and as detailed in the Instruction Manual.
The equipment is designed for use with consumables supplied by Struers. If subjected to misuse, improper
installation, alteration, neglect, accident or improper repair, Struers will accept no responsibility for
damage(s) to the user or the equipment.
Dismantling of any part of the equipment, during service or repair, should always be performed by a qualified
technician (electromechanical, electronic, mechanical, pneumatic, etc.).
Labotom-3
Instruction Manual
1
User’s Guide
Table of Contents Page
1.Getting Started
Checking the Contents of the Crate ................................................... 2
Unpacking Labotom-3 ........................................................................ 2
Placing Labotom-3 ............................................................................. 2
Getting Acquainted with Labotom-3 ................................................... 3
Cooling Valve ............................................................................ 4
Back view .................................................................................. 5
Noise Level ........................................................................................ 6
Supplying Power ................................................................................ 6
Direction of the Cut-off Wheel ................................................... 6
Connecting a Cooli-1/-3/-5 Cooling Unit ............................................. 7
Mounting the Quick-Clamping Device and Spring Clamp .................. 8
2.Basic Operations
Using the Controls .............................................................................. 9
Front Panel Controls of Labotom-3 .......................................... 9
Controls ............................................................................................ 10
Mounting a Cut-off Wheel ................................................................ 11
Dismounting a Cut-off Wheel ........................................................... 11
Clamping the Workpiece .................................................................. 12
Starting/Stopping the Cutting Process ............................................. 13
3.Regular Maintenance
Recirculation Cooling Unit ....................................................... 14
Daily ................................................................................................. 14
Weekly ............................................................................................. 14
Labotom-3
Instruction Manual
2
1. Getting Started
In the packing crate you should find the following parts:
1 Fork spanner 24mm, for changing the cut-off wheel
1 Inlet hose, 13mm dia., 2m
1 Outlet hose, 50mm dia., 2m
4 Hose clamps
1 Elbow pipe, 90°
1 Elbow pipe, 45°
1 Drain pipe
1 Set of Instruction Manuals
Use a 13 mm socket spanner to remove the screws underneath
the pallet.
Labotom-3 should be placed on an optional Struers table unit, or
other suitable table. Ensure that the table is level.
The table should be able to carry a weight of min. 100 kg. The depth
should be at least 750 mm. Generally, the best working position will
be achieved using a table 800 mm high or lower.
Make sure there is enough room behind the table for the inlet and
outlet hoses and for the protection guard to be opened fully.
Checking the Contents
of the Crate
Unpacking Labotom-3
Placing Labotom-3
Note: Placing Labotom-3 on a table unit
Lead the electric cable, inlet and outlet hose through the opening
in the back of the table.
Labotom-3
Instruction Manual
3
Take a moment to familiarise yourself with the location and names of
the Labotom-3 components.
Front panel controls
Lifting handle for protection guard
Protection guard
Cutting handle
Opening for protruding workpieces
Main power switch
Getting Acquainted
with Labotom-3
Labotom-3
Instruction Manual
4
Spindle lock
Tilting cutting unit
Connection for external fume
extraction system (optional kit required)
Cut-off wheel
Cutting table
Quick-clamping device (optional)
Spring clamp (optional)
The cooling valve lever is mounted behind the guard for the cut-off
wheel.
Cutting the lever is turned clockwise and the water is directed
to cool the cut-off wheel.
Cleaning the lever is turned counter-clockwise to flush the
cutting chamber.
Cooling Valve
Lever
Labotom-3
Instruction Manual
5
Electrical cable for power supply
Back plate
Name plate
Flush hose
Water outlet
Water inlet
Cooli Unit connection
Back view
Labotom-3
Instruction Manual
6
Approx. 64 dB (A) measured at idle running, at a distance of
1.0 m/39.4” from the machine.
Labotom-3 is factory mounted with an electric cable. Mount a
plug on the cable:
Black and brown: phase
Yellow/green: earth
Check that the cut-off wheel rotates in the direction indicated by the
arrow on the guard for the cut-off wheel. If the direction of rotation is
incorrect, switch two of the phases.
Noise Level
Supplying Power
IMPORTANT
Check that the mains voltage corresponds to the voltage stated on the type
plate on the back of the machine.
Direction of the Cut-off Wheel
Table des matières
Langues :
Autres manuels Struers Coupeur
