Struers Secotom-10 Manuel utilisateur

Manual No.: 15037001

Date of Release .0.2010

Secotom-10

Instruction Manual

Secotom-10

Instruction Manual

Table of Contents Page

User’s Guide....................................................................................1

Reference Guide..........................................................................31

Quick Reference..........................................................................43

Always state Serial No and Voltage/frequency if you have technical questions or when ordering spare parts.

You will find the Serial No. and Voltage on the type plate of the machine itself. We may also need the Date

and Article No of the manual. This information is found on the front cover.

The following restrictions should be observed, as violation of the restrictions may cause cancellation of

Struers legal obligations:

Instruction Manuals: Struers Instruction Manuals may only be used in connection with Struers equipment

covered by the Instruction Manual.

Service Manuals: Struers Service Manuals may only be used by a trained technician authorised by Struers.

The Service Manual may only be used in connection with Struers equipment covered by the Service Manual.

Struers assumes no responsibility for errors in the manual text/illustrations. The information in this manual is

subject to changes without notice. The manual may mention accessories or parts not included in the present

version of the equipment.

The contents of this manual is the property of Struers. Reproduction of any part of this manual without the

written permission of Struers is not allowed.

Struers A/S

Pederstrupvej 84

DK-2750 Ballerup

Denmark

Telephone +45 44 600 800

Fax +45 44 600 801

Secotom-10

Instruction Manual

Secotom-10

Safety Precaution Sheet

To be read carefully

before use

1. The operator should be fully aware of the use of the machine according

to the Instruction Manual and the instructions of the cut-off wheels.

2. The machine must be placed on a safe and stable support table. All

safety functions and guards of the machine must be in working order.

3. The unit must be installed in compliance with local safety regulations.

4. Use only intact cut-off wheels. The cut-off wheels must be approved for

min. 5,000 rpm.

5. When the manual cutting table is used, the machine is not to be used

with saw-blade type cut-off wheels.

6. Observe the current safety regulations for handling, mixing, filling,

emptying and disposal of the additive for cooling fluid.

7. To achieve maximum safety and lifetime of the machine, use only

original Struers consumables.

8. Struers recommends using cooling fluid when cutting as the materials

being cut may emit harmful dust. Additionally an adequate exhaust

system should be used.

9. The machine emits only moderate noise. However, the cutting process

itself may emit noise, depending on the nature of the workpiece. In

such cases, the use of hearing protection is recommended.

10. Always use Safety Goggles when using the manual cutting table on the

machine.

11. The machine must be disconnected from the mains prior to any service.

Wait until residual potential on the capacitors is discharged.

12. Do not cycle mains power more than once every three minutes.

Damage to the drive will result.

The equipment should only be used for its intended purpose and as detailed in the Instruction Manual.

The equipment is designed for use with consumables supplied by Struers. If subjected to misuse, improper

installation, alteration, neglect, accident or improper repair, Struers will accept no responsibility for

damage(s) to the user or the equipment.

Dismantling of any part of the equipment, during service or repair, should always be performed by a qualified

technician (electromechanical, electronic, mechanical, pneumatic, etc.).

Secotom-10

Instruction Manual

Disposal

Equipment marked with a WEEE symbol contain electrical and

electronic components and must not be disposed of as general

waste.

Please contact your local authorities for information on the correct

method of disposal in accordance with national legislation.

Secotom-10

Instruction Manual

User’s Guide

Table of Contents Page

1. Getting Started

Checking the Contents of the Packing Box........................................2

Removing Secotom-10 from the Pallet...............................................2

Placing Secotom-10...........................................................................2

Cover for Exhaust Hole......................................................................2

Getting Acquainted with Secotom-10.................................................3

Rear of Secotom-10...........................................................................4

Supplying Power ................................................................................5

Single-phase Supply.................................................................5

3-phase Supply.........................................................................5

Connection to the Machine.......................................................5

Mounting the Cut-off Wheel ...............................................................6

Adjusting the Height of the Cut-off Wheel..........................................7

Filling the Cut-off Machine with Cooling Fluid....................................8

Cutting Table......................................................................................9

Positioning the Cutting Table.............................................................9

Attaching Clamping Tools (accessories)..........................................10

Quick-clamping Device...........................................................10

Advanced Clamping Tools......................................................11

Electrical Connections in the Cutting Chamber................................12

Flushing Hose..................................................................................13

2. Basic Operation

Front Panel.......................................................................................14

Front Panel Controls ........................................................................15

Software Settings.............................................................................16

Setting the Language..............................................................17

Reading the Display.........................................................................18

Changing/Editing Values..................................................................19

Numeric Values.......................................................................19

Alphanumeric Values..............................................................20

Setting up the Software....................................................................21

Cutting Setup ...................................................................................22

Setting Wheel Speed..............................................................23

Setting Feed Speed................................................................24

Setting Cut Length..................................................................25

Setting X Position (accessory.................................................26

Chuck Mode (accessory)........................................................28

Starting the Cutting Process ............................................................29

During Cutting.........................................................................29

Stopping the Cutting Process...........................................................30

Secotom-10

Instruction Manual

1. Getting Started

In the packing box you should find the following parts:

1 Secotom-10

2 Mains cables

1 Stop pin

1 Socket spanner 17 mm

1 Socket spanner 13 mm

1 Hose for connection to exhaust, 1.5 m x 32 mm dia.

1 Hose clamp, 25-40 mm dia

1 Cover for exhaust hole

1 Instruction Manual Set

Secotom-10 is secured to the wooden pallet with 3 screws. Remove

these screws with a 13 mm socket spanner.

Secotom-10 should be placed on a safe and stable support table with

an adequate working height. The table must be able to carry at least

55 kg. The machine must be placed close to the power supply.

The exhaust pipe at the back of the cutting chamber can be replaced

with the cover for the exhaust hole if Secotom-10 is not to be

connected to an exhaust system.

Checking the Contents of the

Packing Box

Removing Secotom-10

from the Pallet

Placing Secotom-10

Cover for Exhaust Hole

Secotom-10

Instruction Manual

Take a moment to familiarise yourself with the location and names of

the Secotom-10 components.

Control panel (see 2. Basic Operation)

Movable cutting table

Cut-off wheel mounting

Transparent cover

Cooling fluid nozzles

Ventilation hole

Electrical connection socket

Cover (housing cooling fluid bath and cut-off wheel speed guide)

Cut-off wheel height adjustment control

Main switch (at the back of the machine)

Getting Acquainted with

Secotom-10





















Secotom-10

Instruction Manual

Ventilation Hole

Main switch

Fuses

Mains connection

Type Plate

Rear of Secotom-10











Secotom-10

Instruction Manual

Always remember to switch the power off when installing electrical

equipment!

The Secotom-10 is shipped with 2 types of Mains cables:

The 2-pin (European Schuko) plug is for use on single-phase,

200-240 V connections.

If the plug supplied on this cable is not approved in your country,

then the plug must be replaced with an approved plug. The leads

must be connected as follows:

Yellow/green: earth

Brown: line (live)

Blue: neutral

The 3-pin (North American NEMA) plug is for use on 3-phase,

200-240 V power connections.

If the plug supplied on this cable is not approved in your country,

then the plug must be replaced with an approved plug. The leads

must be connected as follows:

Green: earth

Black: line (live)

White: line (live)

Both cables are on the other end equipped with an IEC 320 cable

connector that has to be connected to the Secotom.

Supplying Power

DANGER!

The machine must be earthed

IMPORTANT

Check that the mains voltage corresponds to the voltage stated

on the type plate on the back of the machine.

Single-phase Supply

3-phase Supply

Connection to the Machine

WARNING!

The output voltage from this cable is 200 – 240V and not 110V.

DO NOT use this cable to connect equipment that use a 110V power

supply. Failure to adhere to this may result in material damage.

Secotom-10

Instruction Manual

Lift the transparent cover to an angle of 450-600.

Lift the cooling fluid nozzles to gain access to the cut-off wheel

mounting.

Insert the stop pin into the hole of the inner flange.

Use the fork spanner (17 mm) to loosen the flange screw.

Remove the outer flange.

Mounting the Cut-off Wheel

IMPORTANT

For manual cutting: only diamond or CBN cut-off wheels with a metal body

are allowed. Abrasive SiC or Al2O3cut-off wheels or saw blades may not be

used when the manual cutting table accessory is fitted to the Secotom-10.

IMPORTANT

The tolerance between the spindle and inner flange is very small which

means that the two surfaces must be absolutely clean.

Never try to squeeze the cut-off wheel on as this may damage the spindle

or the cut-off wheel. If there are any small burrs, remove them with grinding

paper (grit size 1200).

Outer flange

Flange screw

Hole for stop pin

Table des matières

Langues :

Autres manuels Struers Coupeur

Struers

Struers Minitom Manuel utilisateur

Struers

Struers Discotom-60 Manuel utilisateur

Struers

Struers Discotom-100 Manuel utilisateur

Struers

Struers Secotom-60 Manuel utilisateur

Struers

Struers AbraPol-10 Manuel utilisateur

Manuels Coupeur populaires d'autres marques

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuel utilisateur

Makita

Makita DCS552 Manuel utilisateur

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuel utilisateur

Makita

Makita 4112HS Manuel utilisateur

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuel utilisateur

Hitachi

Hitachi CM 4SB2 Guide de dépannage

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuel utilisateur

GCC Technologies

GCC Technologies AFJ-24S Manuel utilisateur

DeWalt

DeWalt XR LI-ION DCS350N Manuel utilisateur

Baudat

Baudat ES1 Manuel utilisateur

Mafell

Mafell ZAF 200 Mode d’emploi

Makita

Makita 4100NH Manuel utilisateur

Formax

Formax FD 574 Manuel utilisateur

EINHELL

EINHELL TE-MA 1500 Manuel utilisateur

Husqvarna

Husqvarna Cut-n-Break K 760 Manuel utilisateur

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuel utilisateur

TRI tool

TRI tool 301A Manuel utilisateur

Roller

Roller King 1 1/4 Manuel utilisateur